blob-cvs-commit

Serial I/O hangification

[Christopher H. <ch...@mu...>]

Is it just me?  If I type characters to blob when blob isn't reading
them (e.g. in the midst of flashing or erasing), the serial i/o hangs.
When the command prompt comes back, blob won't accept any input.

This is on BadgePAD 4 which is SA-1110/SA-1111.

I'm running at 115k2,8N1 with no flow control.

-ch

Re: Serial I/O hangification

[Tim R. <Ti...@Ri...>]

I see the same on IDR.

Christopher Hoover wrote:
> 
> Is it just me?  If I type characters to blob when blob isn't reading
> them (e.g. in the midst of flashing or erasing), the serial i/o hangs.
> When the command prompt comes back, blob won't accept any input.
> 
> This is on BadgePAD 4 which is SA-1110/SA-1111.
> 
> I'm running at 115k2,8N1 with no flow control.
> 
> -ch
> 
> _______________________________________________
> blob-cvs-commit mailing list
> blo...@li...
> https://lists.sourceforge.net/lists/listinfo/blob-cvs-commit

-- 
Tim Riker - http://rikers.org/ - short SIGs! <g>
All I need to know I could have learned in Kindergarten
... if I'd just been paying attention.

Re: Serial I/O hangification

[Abraham vd M. <ab...@2d...>]

Hi Christopher!

> Is it just me?  If I type characters to blob when blob isn't reading
> them (e.g. in the midst of flashing or erasing), the serial i/o hangs.
> When the command prompt comes back, blob won't accept any input.
>=20
> This is on BadgePAD 4 which is SA-1110/SA-1111.
>=20
> I'm running at 115k2,8N1 with no flow control.

Yes, happens to me too.

--=20

Regards
 Abraham

Do you think the "Monkees" should get gas on odd or even days?

__________________________________________________________
 Abraham vd Merwe - 2d3D, Inc.

 Device Driver Development, Outsourcing, Embedded Systems

  Cell: +27 82 565 4451         Snailmail:
   Tel: +27 21 761 7549            Block C, Antree Park
   Fax: +27 21 761 7648            Doncaster Road
 Email: ab...@2d...         Kenilworth, 7700
  Http: http://www.2d3d.com        South Africa

Re: Serial I/O hangification

[Erik M. <J.A...@it...>]

On Wed, Feb 06, 2002 at 05:56:21PM -0800, Christopher Hoover wrote:
> Is it just me?  If I type characters to blob when blob isn't reading
> them (e.g. in the midst of flashing or erasing), the serial i/o hangs.
> When the command prompt comes back, blob won't accept any input.
> 
> This is on BadgePAD 4 which is SA-1110/SA-1111.
> 
> I'm running at 115k2,8N1 with no flow control.

Yes, I've seen it as well. I guess it's something with the new serial
driver, but I still haven't a clue why it happens. I think it's timer
related, I need to go over that code as well.


Erik

-- 
J.A.K. (Erik) Mouw, Information and Communication Theory Group, Faculty
of Information Technology and Systems, Delft University of Technology,
PO BOX 5031, 2600 GA Delft, The Netherlands  Phone: +31-15-2783635
Fax: +31-15-2781843  Email: J.A...@it...
WWW: http://www-ict.its.tudelft.nl/~erik/