Be sure to do the reset circuit (it is a capacitor and switch that connects the RST to 5V. For mal operation as a moonlite focuser it is connected (switch ON) but if you want to upload new firmware to the controller the switch must be OFF. Once finished uploading new firmware, turn switch back to ON for normal operation Information is page13 of pdf.
do you mean : your arduion foucser pro will work with moonlite indi driver and mast add reset circuit for it ??? vrey good
anther issue with easydrive adjusting , when i connecting and the current or voltage is low ( 1.6v to 2.5v) ( current 190mA TO 290mA ) the stepper motor have sounde, Hight than this the steeper came little hot ??? i think i have my muilmeter have issue or the circuit ??!!!!!!!
an idea how to solve it
best regards
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
do you mean : your arduion foucser pro will work with moonlite indi driver and mast add reset circuit for it ???
Yes, it will work with moonlite driver
anther issue with easydrive adjusting
Yes, with the easydriver sometimes it makes a sound. When adjusted right it still makes sound.
If easydriver is ok at 1.6-2.5v and work fine and stepper move ok, then it is ok. Even if it make sound. I also have one easydriver. I adjust that fine, it make sound.
Other easydriver I have - that has no sound. I adjust it same, but this one have sound. I dont know why. But it work fine. So maybe this issue with some easydriver board?
This is why I like DRV8825. Every one I adjust same. But no sound with DRV8825 so I only use that now.
Hope this helps
If it working ok but make sound I think that is ok for easydriver.
Cheers
Robert
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
hi robdert
is there any indi driver for you arduion foucser pro?????
please see
https://www.youtube.com/watch?v=ZwHTn6jpqvQ
by Julian Mullins who uses it on a Mac
and also
https://sourceforge.net/p/arduinofocuscontrollerpro/discussion/general/thread/68a3d8ac/
on the discussion board here where Milen Velinov has it working under INDI
Note that to use it under INI, you use the ASCOM driver - it is moonlite compatible so select it as the moonlite driver
Be sure to do the reset circuit (it is a capacitor and switch that connects the RST to 5V. For mal operation as a moonlite focuser it is connected (switch ON) but if you want to upload new firmware to the controller the switch must be OFF. Once finished uploading new firmware, turn switch back to ON for normal operation Information is page13 of pdf.
Cheers
Robert
Last edit: brownrb 2016-01-15
Dear Robert
Thank for you reply
do you mean : your arduion foucser pro will work with moonlite indi driver and mast add reset circuit for it ??? vrey good
anther issue with easydrive adjusting , when i connecting and the current or voltage is low ( 1.6v to 2.5v) ( current 190mA TO 290mA ) the stepper motor have sounde, Hight than this the steeper came little hot ??? i think i have my muilmeter have issue or the circuit ??!!!!!!!
an idea how to solve it
best regards
Yes, it will work with moonlite driver
Yes, with the easydriver sometimes it makes a sound. When adjusted right it still makes sound.
If easydriver is ok at 1.6-2.5v and work fine and stepper move ok, then it is ok. Even if it make sound. I also have one easydriver. I adjust that fine, it make sound.
Other easydriver I have - that has no sound. I adjust it same, but this one have sound. I dont know why. But it work fine. So maybe this issue with some easydriver board?
This is why I like DRV8825. Every one I adjust same. But no sound with DRV8825 so I only use that now.
Hope this helps
If it working ok but make sound I think that is ok for easydriver.
Cheers
Robert