I was trying to fash the ardiuno nano with The St-6128 Firmware v175 ,and a very thin connector Successfully in SGP PRO with ascom driverr But can not get the stopper to move ,so I try to flash out with arduion focuserpro2Firmware v279 to the stepper motor working popaly in SGP PRO
I think that is something with code for ardruion Firware t6128 v175
So can pleaes check out the arduionFirmware code for st6128 v175 , I would like to to use the model with ekos kstars indi moonlit
Wating for you respond
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
Hi Sami
Please let me know if you can connect with the Windows application first.
If you cannot send me the logfile
I also need to know HOW YOU HAVE CONNECTED the ST6128 driver to the nano - if the connections are wrong then it will not step
Please write down ALL the connections, including power and ground, from the ST6128 driber board to the nano and post here - physcially trace each wire and write down the connection for each wire
It is highly unlikely to be the firmware - more likely to be the connections between the st6128 and the nano
Regards
Robert
Last edit: brownrb 2019-02-22
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
The question is is synthetic difference between the diagram and version 1 and version 2 Hi Robert
I do not use Windows application (not installed ),i always use ascom driver with SGP Pro and diy St6128 work perfect with ardrionfocuserpro2 with Sgp pro (without any issues
The the story that I would like to use the diy st6128 in ekos kstars with moonlit indi driver so I flash the arduino with st6128 v175. Afterward I note that the stepper isn't moving will when I move it with ascom driver (v175) in sgp pro, so i reflash the arduion nano with firmware v279 and try it and work perfect with v279
The issue only with firmware v175 I chack all soild connections between the st-6128 and arduion nano is good
The question is the different between the schematic diagram version pro1 and version pro2
Dear Robert
thank you , yes the file in the attachment work perfact in ascom driver with SGP PRO the stepper motor can i move it now , i think the main upload file v175 st-6128 have error, you need to check it out
waiting for you info
best regards
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
Dear Robert
I was trying to fash the ardiuno nano with The St-6128 Firmware v175 ,and a very thin connector Successfully in SGP PRO with ascom driverr But can not get the stopper to move ,so I try to flash out with arduion focuserpro2Firmware v279 to the stepper motor working popaly in SGP PRO
I think that is something with code for ardruion Firware t6128 v175
So can pleaes check out the arduionFirmware code for st6128 v175 , I would like to to use the model with ekos kstars indi moonlit
Wating for you respond
Hi Sami
Please let me know if you can connect with the Windows application first.
If you cannot send me the logfile
I also need to know HOW YOU HAVE CONNECTED the ST6128 driver to the nano - if the connections are wrong then it will not step
Please write down ALL the connections, including power and ground, from the ST6128 driber board to the nano and post here - physcially trace each wire and write down the connection for each wire
It is highly unlikely to be the firmware - more likely to be the connections between the st6128 and the nano
Regards
Robert
Last edit: brownrb 2019-02-22
The question is is synthetic difference between the diagram and version 1 and version 2 Hi Robert
I do not use Windows application (not installed ),i always use ascom driver with SGP Pro and diy St6128 work perfect with ardrionfocuserpro2 with Sgp pro (without any issues
The the story that I would like to use the diy st6128 in ekos kstars with moonlit indi driver so I flash the arduino with st6128 v175. Afterward I note that the stepper isn't moving will when I move it with ascom driver (v175) in sgp pro, so i reflash the arduion nano with firmware v279 and try it and work perfect with v279
The issue only with firmware v175 I chack all soild connections between the st-6128 and arduion nano is good
The question is the different between the schematic diagram version pro1 and version pro2
the connections are the same for both
// ST6128 CONNECTIONS
// DC+ 12V
// DC- GND
// B- STEPPER MOTOR COIL 2 BLACK
// B+ STEPPER MOTOR COIL 2 GREEN
// A- STEPPER MOTOR COIL 1 BLUE
// A+ STEPPER MOTOR COIL 1 RED
// PUL+ D4
// PUL- GND
// DIR+ D3
// DIR- GND
// ENA+ D8
// ENA- GND
try attached code - there may have been an error in the v175 code
Last edit: brownrb 2019-02-23