Menu ▾ ▴

bootscreen only

General Discussion
chris dillon
2017-03-21
2018-01-21

  • chris dillon

    chris dillon - 2017-03-21

    Goodmorning.
    I have built a 8825 drv based focuser with temp,push buttons and LCD screen 20 position 4 line. I have run all the test and have had success, the build runs the motor one rotation, then the opposite direction.
    however, when I have uploaded the arduino code, 8825_F.ino, 8825_HW203.ino, or the BT variation I only get the boot screen and it seems to hang. I don't have any error message from the arduino sketch. i have all the libraries installed.
    I have run it without the temp sensor and have the same issue. I have checked the FAQ but cant find anything related to this issue. Can anyone assist?

    Cheers

    Chris

     

  • brownrb

    brownrb - 2017-03-22

    Hi Chris
    What sort of Arduino are you running? Its not the Nano 128 version is it? What does the IDE say for the compiled memory size and available memory left?

    I would also check to make sure the libraries are the recommended ones which you can download and install from here.

    It does not seem to be a hardware issue if the basic tests work fine. It points to a possible memory or library issue.

    I would try the _M.INO code as that is the smallest size. Be sure not to make any changes to it.

    Are there any compile error messages? You need to turn on the Show verbose output settings in the Arduino IDE under file preferences. This can show possible problems during compile and upload, which you might miss. It pays to scroll the entire window to see any messages in red.

    Regards
    Robert

     

  • chris dillon

    chris dillon - 2017-03-22

    Hi Robert
    Please see below the verbose output from the upload. I am using a nano, ATmega328. I will check th libraries files.

    Sketch uses 21,288 bytes (69%) of program storage space. Maximum is 30,720 bytes.
    Global variables use 895 bytes (43%) of dynamic memory, leaving 1,153 bytes for local variables. Maximum is 2,048 bytes.
    C:\Program Files\Arduino\hardware\tools\avr/bin/avrdude -CC:\Program Files\Arduino\hardware\tools\avr/etc/avrdude.conf -v -patmega328p -carduino -PCOM4 -b57600 -D -Uflash:w:C:\Users\Astro\AppData\Local\Temp\arduino_build_728440/Focuserv250_DRV8825_HW203_F.ino.hex:i

    avrdude: Version 6.3, compiled on Sep 12 2016 at 17:24:16
    Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
    Copyright (c) 2007-2014 Joerg Wunsch

         System wide configuration file is "C:\Program Files\Arduino\hardware\tools\avr/etc/avrdude.conf"

     Using Port                    : COM4
     Using Programmer              : arduino
     Overriding Baud Rate          : 57600
     AVR Part                      : ATmega328P
     Chip Erase delay              : 9000 us
     PAGEL                         : PD7
     BS2                           : PC2
     RESET disposition             : dedicated
     RETRY pulse                   : SCK
     serial program mode           : yes
     parallel program mode         : yes
     Timeout                       : 200
     StabDelay                     : 100
     CmdexeDelay                   : 25
     SyncLoops                     : 32
     ByteDelay                     : 0
     PollIndex                     : 3
     PollValue                     : 0x53
     Memory Detail                 :

                              Block Poll               Page                       Polled
       Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
       ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
       eeprom        65    20     4    0 no       1024    4      0  3600  3600 0xff 0xff
       flash         65     6   128    0 yes     32768  128    256  4500  4500 0xff 0xff
       lfuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
       hfuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
       efuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
       lock           0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
       calibration    0     0     0    0 no          1    0      0     0     0 0x00 0x00
       signature      0     0     0    0 no          3    0      0     0     0 0x00 0x00

     Programmer Type : Arduino
     Description     : Arduino
     Hardware Version: 2
     Firmware Version: 1.16
     Vtarget         : 0.0 V
     Varef           : 0.0 V
     Oscillator      : Off
     SCK period      : 0.1 us

    avrdude: AVR device initialized and ready to accept instructions

    Reading | ################################################## | 100% 0.01s

    avrdude: Device signature = 0x1e950f (probably m328p)
    avrdude: reading input file "C:\Users\Astro\AppData\Local\Temp\arduino_build_728440/Focuserv250_DRV8825_HW203_F.ino.hex"
    avrdude: writing flash (21288 bytes):

    Writing | ################################################## | 100% 10.65s

    avrdude: 21288 bytes of flash written
    avrdude: verifying flash memory against C:\Users\Astro\AppData\Local\Temp\arduino_build_728440/Focuserv250_DRV8825_HW203_F.ino.hex:
    avrdude: load data flash data from input file C:\Users\Astro\AppData\Local\Temp\arduino_build_728440/Focuserv250_DRV8825_HW203_F.ino.hex:
    avrdude: input file C:\Users\Astro\AppData\Local\Temp\arduino_build_728440/Focuserv250_DRV8825_HW203_F.ino.hex contains 21288 bytes
    avrdude: reading on-chip flash data:

    Reading | ################################################## | 100% 8.98s

    avrdude: verifying ...
    avrdude: 21288 bytes of flash verified

    avrdude done. Thank you.

     

  • chris dillon

    chris dillon - 2017-03-24

    I have updated the libraires and tried again but I have the same result. Any one come across this issue?

     

  • brownrb

    brownrb - 2017-03-24

    That output is nothing like I have seen before from the Arduino IDE.

    In the Arduino IDE, before clicking the compile button
    You have selected Arduino Nano under Tools, Board
    You have selected Tools, Programmer AVRISP mkII

    Please do not use the latest IDE's, 1.6.8 is preferred.

    The following is what I would expect to see, under file preferences show verbose output during compilation

    C:\Program Files (x86)\Arduino\arduino-builder -dump-prefs -logger=machine -hardware "C:\Program Files (x86)\Arduino\hardware" -hardware "C:\Users\robert\AppData\Local\Arduino15\packages" -tools "C:\Program Files (x86)\Arduino\tools-builder" -tools "C:\Program Files (x86)\Arduino\hardware\tools\avr" -tools "C:\Users\robert\AppData\Local\Arduino15\packages" -built-in-libraries "C:\Program Files (x86)\Arduino\libraries" -libraries "D:\Documents\Arduino\libraries" -fqbn=arduino:avr:uno -ide-version=10608 -build-path "D:\TempLocalUser" -warnings=default -prefs=build.warn_data_percentage=75 -verbose "D:\myfiles\myArduino\Arduino Project myFocuserPro2\Arduino Firmware\Focuserv250_DRV8825_HW203_F\Focuserv250_DRV8825_HW203_F.ino"
    C:\Program Files (x86)\Arduino\arduino-builder -compile -logger=machine -hardware "C:\Program Files (x86)\Arduino\hardware" -hardware "C:\Users\robert\AppData\Local\Arduino15\packages" -tools "C:\Program Files (x86)\Arduino\tools-builder" -tools "C:\Program Files (x86)\Arduino\hardware\tools\avr" -tools "C:\Users\robert\AppData\Local\Arduino15\packages" -built-in-libraries "C:\Program Files (x86)\Arduino\libraries" -libraries "D:\Documents\Arduino\libraries" -fqbn=arduino:avr:uno -ide-version=10608 -build-path "D:\TempLocalUser" -warnings=default -prefs=build.warn_data_percentage=75 -verbose "D:\myfiles\myArduino\Arduino Project myFocuserPro2\Arduino Firmware\Focuserv250_DRV8825_HW203_F\Focuserv250_DRV8825_HW203_F.ino"
    Build options changed, rebuilding all
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "D:\TempLocalUser\sketch\Focuserv250_DRV8825_HW203_F.ino.cpp" -o "nul"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-ID:\Documents\Arduino\libraries\OneWire233" "D:\TempLocalUser\sketch\Focuserv250_DRV8825_HW203_F.ino.cpp" -o "nul"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "D:\TempLocalUser\sketch\Focuserv250_DRV8825_HW203_F.ino.cpp" -o "nul"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "D:\TempLocalUser\sketch\Focuserv250_DRV8825_HW203_F.ino.cpp" -o "nul"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "D:\TempLocalUser\sketch\Focuserv250_DRV8825_HW203_F.ino.cpp" -o "nul"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "D:\TempLocalUser\sketch\Focuserv250_DRV8825_HW203_F.ino.cpp" -o "nul"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-ID:\Documents\Arduino\libraries\Bounce2" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "D:\TempLocalUser\sketch\Focuserv250_DRV8825_HW203_F.ino.cpp" -o "nul"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-ID:\Documents\Arduino\libraries\Bounce2" "D:\Documents\Arduino\libraries\OneWire233\OneWire.cpp" -o "nul"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-ID:\Documents\Arduino\libraries\Bounce2" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "D:\Documents\Arduino\libraries\DallasTemperature\DallasTemperature.cpp" -o "nul"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-ID:\Documents\Arduino\libraries\Bounce2" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "C:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src\Wire.cpp" -o "nul"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-ID:\Documents\Arduino\libraries\Bounce2" "C:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src\utility\twi.c" -o "nul"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-ID:\Documents\Arduino\libraries\Bounce2" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "D:\Documents\Arduino\libraries\NewliquidCrystal\FastIO.cpp" -o "nul"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-ID:\Documents\Arduino\libraries\Bounce2" "D:\Documents\Arduino\libraries\NewliquidCrystal\I2CIO.cpp" -o "nul"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-ID:\Documents\Arduino\libraries\Bounce2" "D:\Documents\Arduino\libraries\NewliquidCrystal\LCD.cpp" -o "nul"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-ID:\Documents\Arduino\libraries\Bounce2" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "D:\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal.cpp" -o "nul"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-ID:\Documents\Arduino\libraries\Bounce2" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "D:\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_I2C.cpp" -o "nul"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-ID:\Documents\Arduino\libraries\Bounce2" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "D:\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_I2C_ByVac.cpp" -o "nul"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-ID:\Documents\Arduino\libraries\Bounce2" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "D:\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SI2C.cpp" -o "nul"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-ID:\Documents\Arduino\libraries\Bounce2" "-ID:\Documents\Arduino\libraries\OneWire233" "D:\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR.cpp" -o "nul"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-ID:\Documents\Arduino\libraries\Bounce2" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "D:\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR1W.cpp" -o "nul"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-ID:\Documents\Arduino\libraries\Bounce2" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "D:\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR2W.cpp" -o "nul"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-ID:\Documents\Arduino\libraries\Bounce2" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "D:\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR3W.cpp" -o "nul"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-ID:\Documents\Arduino\libraries\Bounce2" "D:\Documents\Arduino\libraries\NewliquidCrystal\SI2CIO.cpp" -o "nul"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-ID:\Documents\Arduino\libraries\Bounce2" "D:\Documents\Arduino\libraries\Bounce2\Bounce2.cpp" -o "nul"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-ID:\Documents\Arduino\libraries\Bounce2" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "D:\TempLocalUser\sketch\Focuserv250_DRV8825_HW203_F.ino.cpp" -o "nul"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-ID:\Documents\Arduino\libraries\Bounce2" "D:\TempLocalUser\sketch\Focuserv250_DRV8825_HW203_F.ino.cpp" -o "D:\TempLocalUser\preproc\ctags_target_for_gcc_minus_e.cpp"
    "C:\Program Files (x86)\Arduino\tools-builder\ctags\5.8-arduino10/ctags" -u --language-force=c++ -f - --c++-kinds=svpf --fields=KSTtzns --line-directives "D:\TempLocalUser\preproc\ctags_target_for_gcc_minus_e.cpp"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-ID:\Documents\Arduino\libraries\Bounce2" "D:\TempLocalUser\sketch\Focuserv250_DRV8825_HW203_F.ino.cpp" -o "D:\TempLocalUser\sketch\Focuserv250_DRV8825_HW203_F.ino.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-ID:\Documents\Arduino\libraries\Bounce2" "D:\Documents\Arduino\libraries\OneWire233\OneWire.cpp" -o "D:\TempLocalUser\libraries\OneWire233\OneWire.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-ID:\Documents\Arduino\libraries\Bounce2" "D:\Documents\Arduino\libraries\DallasTemperature\DallasTemperature.cpp" -o "D:\TempLocalUser\libraries\DallasTemperature\DallasTemperature.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-ID:\Documents\Arduino\libraries\Bounce2" "C:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src\Wire.cpp" -o "D:\TempLocalUser\libraries\Wire\Wire.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-gcc" -c -g -Os -std=gnu11 -ffunction-sections -fdata-sections -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-ID:\Documents\Arduino\libraries\Bounce2" "C:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src\utility\twi.c" -o "D:\TempLocalUser\libraries\Wire\utility\twi.c.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-ID:\Documents\Arduino\libraries\Bounce2" "D:\Documents\Arduino\libraries\NewliquidCrystal\FastIO.cpp" -o "D:\TempLocalUser\libraries\NewliquidCrystal\FastIO.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-ID:\Documents\Arduino\libraries\Bounce2" "D:\Documents\Arduino\libraries\NewliquidCrystal\I2CIO.cpp" -o "D:\TempLocalUser\libraries\NewliquidCrystal\I2CIO.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-ID:\Documents\Arduino\libraries\Bounce2" "D:\Documents\Arduino\libraries\NewliquidCrystal\LCD.cpp" -o "D:\TempLocalUser\libraries\NewliquidCrystal\LCD.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-ID:\Documents\Arduino\libraries\Bounce2" "D:\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal.cpp" -o "D:\TempLocalUser\libraries\NewliquidCrystal\LiquidCrystal.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-ID:\Documents\Arduino\libraries\Bounce2" "D:\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_I2C.cpp" -o "D:\TempLocalUser\libraries\NewliquidCrystal\LiquidCrystal_I2C.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-ID:\Documents\Arduino\libraries\Bounce2" "D:\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_I2C_ByVac.cpp" -o "D:\TempLocalUser\libraries\NewliquidCrystal\LiquidCrystal_I2C_ByVac.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-ID:\Documents\Arduino\libraries\Bounce2" "D:\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SI2C.cpp" -o "D:\TempLocalUser\libraries\NewliquidCrystal\LiquidCrystal_SI2C.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-ID:\Documents\Arduino\libraries\Bounce2" "D:\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR.cpp" -o "D:\TempLocalUser\libraries\NewliquidCrystal\LiquidCrystal_SR.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-ID:\Documents\Arduino\libraries\Bounce2" "D:\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR1W.cpp" -o "D:\TempLocalUser\libraries\NewliquidCrystal\LiquidCrystal_SR1W.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-ID:\Documents\Arduino\libraries\Bounce2" "D:\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR2W.cpp" -o "D:\TempLocalUser\libraries\NewliquidCrystal\LiquidCrystal_SR2W.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-ID:\Documents\Arduino\libraries\Bounce2" "D:\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR3W.cpp" -o "D:\TempLocalUser\libraries\NewliquidCrystal\LiquidCrystal_SR3W.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-ID:\Documents\Arduino\libraries\Bounce2" "D:\Documents\Arduino\libraries\NewliquidCrystal\SI2CIO.cpp" -o "D:\TempLocalUser\libraries\NewliquidCrystal\SI2CIO.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "-ID:\Documents\Arduino\libraries\OneWire233" "-ID:\Documents\Arduino\libraries\DallasTemperature" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-ID:\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-ID:\Documents\Arduino\libraries\Bounce2" "D:\Documents\Arduino\libraries\Bounce2\Bounce2.cpp" -o "D:\TempLocalUser\libraries\Bounce2\Bounce2.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-gcc" -c -g -x assembler-with-cpp -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "C:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino\wiring_pulse.S" -o "D:\TempLocalUser\core\wiring_pulse.S.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-gcc" -c -g -Os -std=gnu11 -ffunction-sections -fdata-sections -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "C:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino\WInterrupts.c" -o "D:\TempLocalUser\core\WInterrupts.c.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-gcc" -c -g -Os -std=gnu11 -ffunction-sections -fdata-sections -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "C:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino\hooks.c" -o "D:\TempLocalUser\core\hooks.c.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-gcc" -c -g -Os -std=gnu11 -ffunction-sections -fdata-sections -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "C:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino\wiring.c" -o "D:\TempLocalUser\core\wiring.c.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-gcc" -c -g -Os -std=gnu11 -ffunction-sections -fdata-sections -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "C:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino\wiring_analog.c" -o "D:\TempLocalUser\core\wiring_analog.c.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-gcc" -c -g -Os -std=gnu11 -ffunction-sections -fdata-sections -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "C:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino\wiring_digital.c" -o "D:\TempLocalUser\core\wiring_digital.c.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-gcc" -c -g -Os -std=gnu11 -ffunction-sections -fdata-sections -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "C:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino\wiring_pulse.c" -o "D:\TempLocalUser\core\wiring_pulse.c.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-gcc" -c -g -Os -std=gnu11 -ffunction-sections -fdata-sections -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "C:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino\wiring_shift.c" -o "D:\TempLocalUser\core\wiring_shift.c.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "C:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino\CDC.cpp" -o "D:\TempLocalUser\core\CDC.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "C:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino\HardwareSerial.cpp" -o "D:\TempLocalUser\core\HardwareSerial.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "C:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino\HardwareSerial0.cpp" -o "D:\TempLocalUser\core\HardwareSerial0.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "C:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino\HardwareSerial1.cpp" -o "D:\TempLocalUser\core\HardwareSerial1.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "C:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino\HardwareSerial2.cpp" -o "D:\TempLocalUser\core\HardwareSerial2.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "C:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino\HardwareSerial3.cpp" -o "D:\TempLocalUser\core\HardwareSerial3.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "C:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino\IPAddress.cpp" -o "D:\TempLocalUser\core\IPAddress.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "C:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino\PluggableUSB.cpp" -o "D:\TempLocalUser\core\PluggableUSB.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "C:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino\Print.cpp" -o "D:\TempLocalUser\core\Print.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "C:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino\Stream.cpp" -o "D:\TempLocalUser\core\Stream.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "C:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino\Tone.cpp" -o "D:\TempLocalUser\core\Tone.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "C:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino\USBCore.cpp" -o "D:\TempLocalUser\core\USBCore.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "C:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino\WMath.cpp" -o "D:\TempLocalUser\core\WMath.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "C:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino\WString.cpp" -o "D:\TempLocalUser\core\WString.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "C:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino\abi.cpp" -o "D:\TempLocalUser\core\abi.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "C:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino\main.cpp" -o "D:\TempLocalUser\core\main.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_UNO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\standard" "C:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino\new.cpp" -o "D:\TempLocalUser\core\new.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-ar" rcs "D:\TempLocalUser\core\core.a" "D:\TempLocalUser\core\wiring_pulse.S.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-ar" rcs "D:\TempLocalUser\core\core.a" "D:\TempLocalUser\core\WInterrupts.c.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-ar" rcs "D:\TempLocalUser\core\core.a" "D:\TempLocalUser\core\hooks.c.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-ar" rcs "D:\TempLocalUser\core\core.a" "D:\TempLocalUser\core\wiring.c.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-ar" rcs "D:\TempLocalUser\core\core.a" "D:\TempLocalUser\core\wiring_analog.c.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-ar" rcs "D:\TempLocalUser\core\core.a" "D:\TempLocalUser\core\wiring_digital.c.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-ar" rcs "D:\TempLocalUser\core\core.a" "D:\TempLocalUser\core\wiring_pulse.c.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-ar" rcs "D:\TempLocalUser\core\core.a" "D:\TempLocalUser\core\wiring_shift.c.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-ar" rcs "D:\TempLocalUser\core\core.a" "D:\TempLocalUser\core\CDC.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-ar" rcs "D:\TempLocalUser\core\core.a" "D:\TempLocalUser\core\HardwareSerial.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-ar" rcs "D:\TempLocalUser\core\core.a" "D:\TempLocalUser\core\HardwareSerial0.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-ar" rcs "D:\TempLocalUser\core\core.a" "D:\TempLocalUser\core\HardwareSerial1.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-ar" rcs "D:\TempLocalUser\core\core.a" "D:\TempLocalUser\core\HardwareSerial2.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-ar" rcs "D:\TempLocalUser\core\core.a" "D:\TempLocalUser\core\HardwareSerial3.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-ar" rcs "D:\TempLocalUser\core\core.a" "D:\TempLocalUser\core\IPAddress.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-ar" rcs "D:\TempLocalUser\core\core.a" "D:\TempLocalUser\core\PluggableUSB.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-ar" rcs "D:\TempLocalUser\core\core.a" "D:\TempLocalUser\core\Print.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-ar" rcs "D:\TempLocalUser\core\core.a" "D:\TempLocalUser\core\Stream.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-ar" rcs "D:\TempLocalUser\core\core.a" "D:\TempLocalUser\core\Tone.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-ar" rcs "D:\TempLocalUser\core\core.a" "D:\TempLocalUser\core\USBCore.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-ar" rcs "D:\TempLocalUser\core\core.a" "D:\TempLocalUser\core\WMath.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-ar" rcs "D:\TempLocalUser\core\core.a" "D:\TempLocalUser\core\WString.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-ar" rcs "D:\TempLocalUser\core\core.a" "D:\TempLocalUser\core\abi.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-ar" rcs "D:\TempLocalUser\core\core.a" "D:\TempLocalUser\core\main.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-ar" rcs "D:\TempLocalUser\core\core.a" "D:\TempLocalUser\core\new.cpp.o"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-gcc" -Os -Wl,--gc-sections -mmcu=atmega328p -o "D:\TempLocalUser/Focuserv250_DRV8825_HW203_F.ino.elf" "D:\TempLocalUser\sketch\Focuserv250_DRV8825_HW203_F.ino.cpp.o" "D:\TempLocalUser\libraries\OneWire233\OneWire.cpp.o" "D:\TempLocalUser\libraries\DallasTemperature\DallasTemperature.cpp.o" "D:\TempLocalUser\libraries\Wire\Wire.cpp.o" "D:\TempLocalUser\libraries\Wire\utility\twi.c.o" "D:\TempLocalUser\libraries\NewliquidCrystal\FastIO.cpp.o" "D:\TempLocalUser\libraries\NewliquidCrystal\I2CIO.cpp.o" "D:\TempLocalUser\libraries\NewliquidCrystal\LCD.cpp.o" "D:\TempLocalUser\libraries\NewliquidCrystal\LiquidCrystal.cpp.o" "D:\TempLocalUser\libraries\NewliquidCrystal\LiquidCrystal_I2C.cpp.o" "D:\TempLocalUser\libraries\NewliquidCrystal\LiquidCrystal_I2C_ByVac.cpp.o" "D:\TempLocalUser\libraries\NewliquidCrystal\LiquidCrystal_SI2C.cpp.o" "D:\TempLocalUser\libraries\NewliquidCrystal\LiquidCrystal_SR.cpp.o" "D:\TempLocalUser\libraries\NewliquidCrystal\LiquidCrystal_SR1W.cpp.o" "D:\TempLocalUser\libraries\NewliquidCrystal\LiquidCrystal_SR2W.cpp.o" "D:\TempLocalUser\libraries\NewliquidCrystal\LiquidCrystal_SR3W.cpp.o" "D:\TempLocalUser\libraries\NewliquidCrystal\SI2CIO.cpp.o" "D:\TempLocalUser\libraries\Bounce2\Bounce2.cpp.o" "D:\TempLocalUser/core\core.a" "-LD:\TempLocalUser" -lm
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-objcopy" -O ihex -j .eeprom --set-section-flags=.eeprom=alloc,load --no-change-warnings --change-section-lma .eeprom=0 "D:\TempLocalUser/Focuserv250_DRV8825_HW203_F.ino.elf" "D:\TempLocalUser/Focuserv250_DRV8825_HW203_F.ino.eep"
    "C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-objcopy" -O ihex -R .eeprom "D:\TempLocalUser/Focuserv250_DRV8825_HW203_F.ino.elf" "D:\TempLocalUser/Focuserv250_DRV8825_HW203_F.ino.hex"
    Using library OneWire233 at version 2.3.3 in folder: D:\Documents\Arduino\libraries\OneWire233
    Using library DallasTemperature at version 3.7.6 in folder: D:\Documents\Arduino\libraries\DallasTemperature
    Using library Wire at version 1.0 in folder: C:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire
    Using library NewliquidCrystal in folder: D:\Documents\Arduino\libraries\NewliquidCrystal (legacy)
    Using library EEPROM at version 2.0 in folder: C:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\EEPROM
    Using library Bounce2 at version 2.2 in folder: D:\Documents\Arduino\libraries\Bounce2

    Sketch uses 23,706 bytes (73%) of program storage space. Maximum is 32,256 bytes.
    Global variables use 973 bytes (47%) of dynamic memory, leaving 1,075 bytes for local variables. Maximum is 2,048 bytes.

     

  • chris dillon

    chris dillon - 2017-03-25

    Robert,
    I have compile it in ide v 1.6.8. the board and the baord name and processor are correct from the above post. the out put from the erroe log does show a few warning. please see the attached txt file. mainly the -Wunsed command for usec, value etc. What would be the best way forward from here?

     
    compile_verbose.txt

  • brownrb

    brownrb - 2017-03-25

    Hi Chris
    Ok, from the file, this much is clear
    There are issues with the liquid crystal library for the lcd.
    in C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal

    There are issues with EEPROM.h
    C:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src

    I would recommend the following
    Uninstall the Arduino IDE
    If after uninstall, navigate to C:\Program Files\
    and if there is an Arduino sub folder delete it.

    Navigate to C:\Users\Astro\Documents\Arduino\ and rename the libraries folder as oldlibraries and make a new libraries folder which has nothing in it

    REBOOT

    Download this library attached - it has the zip files for libraries you need

    Download the 1.6.8 Arduino IDE, and then install it as administrator mode
    https://www.arduino.cc/download_handler.php?f=/arduino-1.6.8-windows.exe

    Once IDE is installed, then install the newliquidcrystallibrary above (using Skerch, Include library, add ZIP library and selecting NewliquidCrystal_1.3.4.zip

    install the Arduino Temperature Library (same process and for newliquidcrystallibrary)

    install the OneWire library (as per process)

    install the Bounce2 library (as per process)

    Ensure that the Focuserv250_DRV8825_HW203_F.ino and eepromanything.h files are in the same folder.

    Double click on the .ino file to start the Arduino IDE and it should compile without any warnings. This is what we need to get to - no warnings during compilation (as you can see in my case above).

    Let me know how it goes

     
    Libraries.zip

  • chris dillon

    chris dillon - 2017-03-25

    Thanks Robert I attempted the instructions in the above post and still got warnings, will atempt to track the individaul warnins down in arduino posts. all the test programs work but when bundled to gether it hangs. i will run the lcd test program and see the compile output

    C:\Program Files\Arduino\arduino-builder -dump-prefs -logger=machine -hardware "C:\Program Files\Arduino\hardware" -tools "C:\Program Files\Arduino\tools-builder" -tools "C:\Program Files\Arduino\hardware\tools\avr" -built-in-libraries "C:\Program Files\Arduino\libraries" -libraries "C:\Users\Astro\Documents\Arduino\libraries" -fqbn=arduino:avr:nano:cpu=atmega328 -ide-version=10608 -build-path "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp" -warnings=all -prefs=build.warn_data_percentage=75 -verbose "C:\Users\Astro\Documents\focuser\Focuserv250_DRV8825_HW203_F\Focuserv250_DRV8825_HW203_F.ino"
    C:\Program Files\Arduino\arduino-builder -compile -logger=machine -hardware "C:\Program Files\Arduino\hardware" -tools "C:\Program Files\Arduino\tools-builder" -tools "C:\Program Files\Arduino\hardware\tools\avr" -built-in-libraries "C:\Program Files\Arduino\libraries" -libraries "C:\Users\Astro\Documents\Arduino\libraries" -fqbn=arduino:avr:nano:cpu=atmega328 -ide-version=10608 -build-path "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp" -warnings=all -prefs=build.warn_data_percentage=75 -verbose "C:\Users\Astro\Documents\focuser\Focuserv250_DRV8825_HW203_F\Focuserv250_DRV8825_HW203_F.ino"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\sketch\Focuserv250_DRV8825_HW203_F.ino.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\sketch\Focuserv250_DRV8825_HW203_F.ino.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\sketch\Focuserv250_DRV8825_HW203_F.ino.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\sketch\Focuserv250_DRV8825_HW203_F.ino.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\sketch\Focuserv250_DRV8825_HW203_F.ino.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\sketch\Focuserv250_DRV8825_HW203_F.ino.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\sketch\Focuserv250_DRV8825_HW203_F.ino.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "C:\Users\Astro\Documents\Arduino\libraries\OneWire-master\OneWire.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "C:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master\DallasTemperature.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "C:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src\Wire.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "C:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src\utility\twi.c" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\FastIO.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\I2CIO.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_I2C.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_I2C_ByVac.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SI2C.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR1W.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR2W.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR3W.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\SI2CIO.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "C:\Users\Astro\Documents\Arduino\libraries\Bounce2-master\Bounce2.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\sketch\Focuserv250_DRV8825_HW203_F.ino.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\sketch\Focuserv250_DRV8825_HW203_F.ino.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\preproc\ctags_target_for_gcc_minus_e.cpp"
    "C:\Program Files\Arduino\tools-builder\ctags\5.8-arduino10/ctags" -u --language-force=c++ -f - --c++-kinds=svpf --fields=KSTtzns --line-directives "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\preproc\ctags_target_for_gcc_minus_e.cpp"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\sketch\Focuserv250_DRV8825_HW203_F.ino.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\sketch\Focuserv250_DRV8825_HW203_F.ino.cpp.o"
    In file included from C:\Users\Astro\Documents\focuser\Focuserv250_DRV8825_HW203_F\Focuserv250_DRV8825_HW203_F.ino:106:0:

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal/LCD.h:89:20: warning: unused parameter 'uSec' [-Wunused-parameter]

    inline static void waitUsec ( uint16_t uSec )

                    ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal/LCD.h:486:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklightPin ( uint8_t value, t_backlighPol pol ) { };

             ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal/LCD.h:486:17: warning: unused parameter 'pol' [-Wunused-parameter]

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal/LCD.h:505:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklight ( uint8_t value ) { };

             ^

    In file included from C:\Users\Astro\Documents\focuser\Focuserv250_DRV8825_HW203_F\Focuserv250_DRV8825_HW203_F.ino:108:0:

    C:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src/EEPROM.h:43:30: warning: type qualifiers ignored on function return type [-Wignored-qualifiers]

     operator const uint8_t() const       { return **this; }

                          ^

    C:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src/EEPROM.h:92:26: warning: type qualifiers ignored on function return type [-Wignored-qualifiers]

     operator const int() const          { return index; }

                      ^

    C:\Users\Astro\Documents\focuser\Focuserv250_DRV8825_HW203_F\Focuserv250_DRV8825_HW203_F.ino:476:6: warning: unused parameter 'command' [-Wunused-parameter]

    void processCommand(String command)

      ^

    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "C:\Users\Astro\Documents\Arduino\libraries\OneWire-master\OneWire.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\OneWire-master\OneWire.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "C:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master\DallasTemperature.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\Arduino-Temperature-Control-Library-master\DallasTemperature.cpp.o"
    C:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master\DallasTemperature.cpp:808:6: warning: unused parameter 'deviceAddress' [-Wunused-parameter]

    void DallasTemperature::defaultAlarmHandler(const uint8_t* deviceAddress){}

      ^

    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "C:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src\Wire.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\Wire\Wire.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-gcc" -c -g -Os -Wall -Wextra -std=gnu11 -ffunction-sections -fdata-sections -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "C:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src\utility\twi.c" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\Wire\utility\twi.c.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\utility" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\FastIO.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\FastIO.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\utility" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\I2CIO.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\I2CIO.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\utility" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\LCD.cpp.o"
    In file included from C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.cpp:46:0:

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:89:20: warning: unused parameter 'uSec' [-Wunused-parameter]

    inline static void waitUsec ( uint16_t uSec )

                    ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:486:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklightPin ( uint8_t value, t_backlighPol pol ) { };

             ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:486:17: warning: unused parameter 'pol' [-Wunused-parameter]

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:505:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklight ( uint8_t value ) { };

             ^

    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\utility" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\LiquidCrystal.cpp.o"
    In file included from C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal.h:32:0,

                 from C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal.cpp:38:

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:89:20: warning: unused parameter 'uSec' [-Wunused-parameter]

    inline static void waitUsec ( uint16_t uSec )

                    ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:486:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklightPin ( uint8_t value, t_backlighPol pol ) { };

             ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:486:17: warning: unused parameter 'pol' [-Wunused-parameter]

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:505:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklight ( uint8_t value ) { };

             ^

    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\utility" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_I2C.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\LiquidCrystal_I2C.cpp.o"
    In file included from C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_I2C.h:35:0,

                 from C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_I2C.cpp:37:

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:89:20: warning: unused parameter 'uSec' [-Wunused-parameter]

    inline static void waitUsec ( uint16_t uSec )

                    ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:486:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklightPin ( uint8_t value, t_backlighPol pol ) { };

             ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:486:17: warning: unused parameter 'pol' [-Wunused-parameter]

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:505:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklight ( uint8_t value ) { };

             ^

    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\utility" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_I2C_ByVac.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\LiquidCrystal_I2C_ByVac.cpp.o"
    In file included from C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_I2C_ByVac.h:38:0,

                 from C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_I2C_ByVac.cpp:34:

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:89:20: warning: unused parameter 'uSec' [-Wunused-parameter]

    inline static void waitUsec ( uint16_t uSec )

                    ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:486:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklightPin ( uint8_t value, t_backlighPol pol ) { };

             ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:486:17: warning: unused parameter 'pol' [-Wunused-parameter]

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:505:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklight ( uint8_t value ) { };

             ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_I2C_ByVac.cpp: In constructor 'LiquidCrystal_I2C_ByVac::LiquidCrystal_I2C_ByVac(uint8_t)':

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_I2C_ByVac.cpp:41:14: warning: statement has no effect [-Wunused-value]

    _polarity == NEGATIVE;

          ^

    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\utility" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SI2C.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\LiquidCrystal_SI2C.cpp.o"
    In file included from C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SI2C.h:38:0,

                 from C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SI2C.cpp:40:

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:89:20: warning: unused parameter 'uSec' [-Wunused-parameter]

    inline static void waitUsec ( uint16_t uSec )

                    ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:486:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklightPin ( uint8_t value, t_backlighPol pol ) { };

             ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:486:17: warning: unused parameter 'pol' [-Wunused-parameter]

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:505:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklight ( uint8_t value ) { };

             ^

    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\utility" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\LiquidCrystal_SR.cpp.o"
    In file included from C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR.h:84:0,

                 from C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR.cpp:90:

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:89:20: warning: unused parameter 'uSec' [-Wunused-parameter]

    inline static void waitUsec ( uint16_t uSec )

                    ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:486:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklightPin ( uint8_t value, t_backlighPol pol ) { };

             ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:486:17: warning: unused parameter 'pol' [-Wunused-parameter]

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:505:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklight ( uint8_t value ) { };

             ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR.cpp:110:6: warning: unused parameter 'lines' [-Wunused-parameter]

    void LiquidCrystal_SR::init(uint8_t srdata, uint8_t srclock, uint8_t enable, 

      ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR.cpp:110:6: warning: unused parameter 'font' [-Wunused-parameter]

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR.cpp:202:6: warning: unused parameter 'pin' [-Wunused-parameter]

    void LiquidCrystal_SR::setBacklightPin ( uint8_t pin, t_backlighPol pol )

      ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR.cpp:202:6: warning: unused parameter 'pol' [-Wunused-parameter]

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR.cpp:207:6: warning: unused parameter 'mode' [-Wunused-parameter]

    void LiquidCrystal_SR::setBacklight ( uint8_t mode ) 

      ^

    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\utility" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR1W.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\LiquidCrystal_SR1W.cpp.o"
    In file included from C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR1W.cpp:35:0:

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR1W.h:157:1: warning: multi-line comment [-Wcomment]

    // | | 0.1uF | \

    ^

    In file included from C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR1W.h:266:0,

                 from C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR1W.cpp:35:

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:89:20: warning: unused parameter 'uSec' [-Wunused-parameter]

    inline static void waitUsec ( uint16_t uSec )

                    ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:486:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklightPin ( uint8_t value, t_backlighPol pol ) { };

             ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:486:17: warning: unused parameter 'pol' [-Wunused-parameter]

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:505:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklight ( uint8_t value ) { };

             ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR1W.cpp:50:6: warning: unused parameter 'lines' [-Wunused-parameter]

    void LiquidCrystal_SR1W::init(uint8_t srdata, t_sr1w_circuitType circuitType, t_backlighPol blpol, uint8_t lines, uint8_t font)

      ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR1W.cpp:50:6: warning: unused parameter 'font' [-Wunused-parameter]

    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\utility" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR2W.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\LiquidCrystal_SR2W.cpp.o"
    In file included from C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR2W.h:125:0,

                 from C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR2W.cpp:32:

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:89:20: warning: unused parameter 'uSec' [-Wunused-parameter]

    inline static void waitUsec ( uint16_t uSec )

                    ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:486:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklightPin ( uint8_t value, t_backlighPol pol ) { };

             ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:486:17: warning: unused parameter 'pol' [-Wunused-parameter]

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:505:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklight ( uint8_t value ) { };

             ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR2W.cpp:48:6: warning: unused parameter 'lines' [-Wunused-parameter]

    void LiquidCrystal_SR2W::init(uint8_t srdata, uint8_t srclock, t_backlighPol blpol, uint8_t lines, uint8_t font)

      ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR2W.cpp:48:6: warning: unused parameter 'font' [-Wunused-parameter]

    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\utility" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR3W.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\LiquidCrystal_SR3W.cpp.o"
    In file included from C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR3W.h:62:0,

                 from C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR3W.cpp:77:

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:89:20: warning: unused parameter 'uSec' [-Wunused-parameter]

    inline static void waitUsec ( uint16_t uSec )

                    ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:486:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklightPin ( uint8_t value, t_backlighPol pol ) { };

             ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:486:17: warning: unused parameter 'pol' [-Wunused-parameter]

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:505:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklight ( uint8_t value ) { };

             ^

    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\utility" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\SI2CIO.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\SI2CIO.cpp.o"
    In file included from C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\SI2CIO.cpp:51:0:

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\SoftI2CMaster.h:271:7: warning: unused parameter 'addr' [-Wunused-parameter]

    bool i2c_start(uint8_t addr)

       ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\SoftI2CMaster.h:289:7: warning: unused parameter 'addr' [-Wunused-parameter]

    bool i2c_rep_start(uint8_t addr)

       ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\SoftI2CMaster.h:314:7: warning: unused parameter 'addr' [-Wunused-parameter]

    void i2c_start_wait(uint8_t addr)

       ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\SoftI2CMaster.h:361:6: warning: unused parameter 'value' [-Wunused-parameter]

    bool i2c_write(uint8_t value)

      ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\SoftI2CMaster.h:438:9: warning: unused parameter 'last' [-Wunused-parameter]

    uint8_t i2c_read(bool last)

         ^

    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "C:\Users\Astro\Documents\Arduino\libraries\Bounce2-master\Bounce2.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\Bounce2-master\Bounce2.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-gcc" -c -g -x assembler-with-cpp -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\wiring_pulse.S" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\wiring_pulse.S.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-gcc" -c -g -Os -Wall -Wextra -std=gnu11 -ffunction-sections -fdata-sections -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\WInterrupts.c" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\WInterrupts.c.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-gcc" -c -g -Os -Wall -Wextra -std=gnu11 -ffunction-sections -fdata-sections -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\hooks.c" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\hooks.c.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-gcc" -c -g -Os -Wall -Wextra -std=gnu11 -ffunction-sections -fdata-sections -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\wiring.c" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\wiring.c.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-gcc" -c -g -Os -Wall -Wextra -std=gnu11 -ffunction-sections -fdata-sections -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\wiring_analog.c" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\wiring_analog.c.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-gcc" -c -g -Os -Wall -Wextra -std=gnu11 -ffunction-sections -fdata-sections -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\wiring_digital.c" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\wiring_digital.c.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-gcc" -c -g -Os -Wall -Wextra -std=gnu11 -ffunction-sections -fdata-sections -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\wiring_pulse.c" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\wiring_pulse.c.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-gcc" -c -g -Os -Wall -Wextra -std=gnu11 -ffunction-sections -fdata-sections -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\wiring_shift.c" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\wiring_shift.c.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\CDC.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\CDC.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\HardwareSerial.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\HardwareSerial.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\HardwareSerial0.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\HardwareSerial0.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\HardwareSerial1.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\HardwareSerial1.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\HardwareSerial2.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\HardwareSerial2.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\HardwareSerial3.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\HardwareSerial3.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\IPAddress.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\IPAddress.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\PluggableUSB.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\PluggableUSB.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\Print.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\Print.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\Stream.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\Stream.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\Tone.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\Tone.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\USBCore.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\USBCore.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\WMath.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\WMath.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\WString.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\WString.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\abi.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\abi.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\main.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\main.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\new.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\new.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\wiring_pulse.S.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\WInterrupts.c.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\hooks.c.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\wiring.c.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\wiring_analog.c.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\wiring_digital.c.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\wiring_pulse.c.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\wiring_shift.c.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\CDC.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\HardwareSerial.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\HardwareSerial0.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\HardwareSerial1.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\HardwareSerial2.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\HardwareSerial3.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\IPAddress.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\PluggableUSB.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\Print.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\Stream.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\Tone.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\USBCore.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\WMath.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\WString.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\abi.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\main.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\new.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-gcc" -Wall -Wextra -Os -Wl,--gc-sections -mmcu=atmega328p -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp/Focuserv250_DRV8825_HW203_F.ino.elf" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\sketch\Focuserv250_DRV8825_HW203_F.ino.cpp.o" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\OneWire-master\OneWire.cpp.o" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\Arduino-Temperature-Control-Library-master\DallasTemperature.cpp.o" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\Wire\Wire.cpp.o" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\Wire\utility\twi.c.o" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\FastIO.cpp.o" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\I2CIO.cpp.o" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\LCD.cpp.o" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\LiquidCrystal.cpp.o" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\LiquidCrystal_I2C.cpp.o" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\LiquidCrystal_I2C_ByVac.cpp.o" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\LiquidCrystal_SI2C.cpp.o" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\LiquidCrystal_SR.cpp.o" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\LiquidCrystal_SR1W.cpp.o" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\LiquidCrystal_SR2W.cpp.o" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\LiquidCrystal_SR3W.cpp.o" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\SI2CIO.cpp.o" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\Bounce2-master\Bounce2.cpp.o" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp/core\core.a" "-LC:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp" -lm
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-objcopy" -O ihex -j .eeprom --set-section-flags=.eeprom=alloc,load --no-change-warnings --change-section-lma .eeprom=0 "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp/Focuserv250_DRV8825_HW203_F.ino.elf" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp/Focuserv250_DRV8825_HW203_F.ino.eep"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-objcopy" -O ihex -R .eeprom "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp/Focuserv250_DRV8825_HW203_F.ino.elf" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp/Focuserv250_DRV8825_HW203_F.ino.hex"
    Using library OneWire-master at version 2.3.2 in folder: C:\Users\Astro\Documents\Arduino\libraries\OneWire-master
    Using library Arduino-Temperature-Control-Library-master at version 3.7.7 in folder: C:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master
    Using library Wire at version 1.0 in folder: C:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire
    Using library NewliquidCrystal in folder: C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal (legacy)
    Using library EEPROM at version 2.0 in folder: C:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM
    Using library Bounce2-master at version 2.21 in folder: C:\Users\Astro\Documents\Arduino\libraries\Bounce2-master

    Sketch uses 23,830 bytes (77%) of program storage space. Maximum is 30,720 bytes.
    Global variables use 973 bytes (47%) of dynamic memory, leaving 1,075 bytes for local variables. Maximum is 2,048 bytes.

     

  • chris dillon

    chris dillon - 2017-03-25

    Thanks Robert I attempted the instructions in the above post and still got warnings, will atempt to track the individaul warnins down in arduino posts. all the test programs work but when bundled to gether it hangs. i will run the lcd test program and see the compile output

    C:\Program Files\Arduino\arduino-builder -dump-prefs -logger=machine -hardware "C:\Program Files\Arduino\hardware" -tools "C:\Program Files\Arduino\tools-builder" -tools "C:\Program Files\Arduino\hardware\tools\avr" -built-in-libraries "C:\Program Files\Arduino\libraries" -libraries "C:\Users\Astro\Documents\Arduino\libraries" -fqbn=arduino:avr:nano:cpu=atmega328 -ide-version=10608 -build-path "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp" -warnings=all -prefs=build.warn_data_percentage=75 -verbose "C:\Users\Astro\Documents\focuser\Focuserv250_DRV8825_HW203_F\Focuserv250_DRV8825_HW203_F.ino"
    C:\Program Files\Arduino\arduino-builder -compile -logger=machine -hardware "C:\Program Files\Arduino\hardware" -tools "C:\Program Files\Arduino\tools-builder" -tools "C:\Program Files\Arduino\hardware\tools\avr" -built-in-libraries "C:\Program Files\Arduino\libraries" -libraries "C:\Users\Astro\Documents\Arduino\libraries" -fqbn=arduino:avr:nano:cpu=atmega328 -ide-version=10608 -build-path "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp" -warnings=all -prefs=build.warn_data_percentage=75 -verbose "C:\Users\Astro\Documents\focuser\Focuserv250_DRV8825_HW203_F\Focuserv250_DRV8825_HW203_F.ino"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\sketch\Focuserv250_DRV8825_HW203_F.ino.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\sketch\Focuserv250_DRV8825_HW203_F.ino.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\sketch\Focuserv250_DRV8825_HW203_F.ino.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\sketch\Focuserv250_DRV8825_HW203_F.ino.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\sketch\Focuserv250_DRV8825_HW203_F.ino.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\sketch\Focuserv250_DRV8825_HW203_F.ino.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\sketch\Focuserv250_DRV8825_HW203_F.ino.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "C:\Users\Astro\Documents\Arduino\libraries\OneWire-master\OneWire.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "C:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master\DallasTemperature.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "C:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src\Wire.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "C:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src\utility\twi.c" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\FastIO.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\I2CIO.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_I2C.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_I2C_ByVac.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SI2C.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR1W.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR2W.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR3W.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\SI2CIO.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "C:\Users\Astro\Documents\Arduino\libraries\Bounce2-master\Bounce2.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\sketch\Focuserv250_DRV8825_HW203_F.ino.cpp" -o "nul"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\sketch\Focuserv250_DRV8825_HW203_F.ino.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\preproc\ctags_target_for_gcc_minus_e.cpp"
    "C:\Program Files\Arduino\tools-builder\ctags\5.8-arduino10/ctags" -u --language-force=c++ -f - --c++-kinds=svpf --fields=KSTtzns --line-directives "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\preproc\ctags_target_for_gcc_minus_e.cpp"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\sketch\Focuserv250_DRV8825_HW203_F.ino.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\sketch\Focuserv250_DRV8825_HW203_F.ino.cpp.o"
    In file included from C:\Users\Astro\Documents\focuser\Focuserv250_DRV8825_HW203_F\Focuserv250_DRV8825_HW203_F.ino:106:0:

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal/LCD.h:89:20: warning: unused parameter 'uSec' [-Wunused-parameter]

    inline static void waitUsec ( uint16_t uSec )

                    ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal/LCD.h:486:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklightPin ( uint8_t value, t_backlighPol pol ) { };

             ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal/LCD.h:486:17: warning: unused parameter 'pol' [-Wunused-parameter]

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal/LCD.h:505:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklight ( uint8_t value ) { };

             ^

    In file included from C:\Users\Astro\Documents\focuser\Focuserv250_DRV8825_HW203_F\Focuserv250_DRV8825_HW203_F.ino:108:0:

    C:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src/EEPROM.h:43:30: warning: type qualifiers ignored on function return type [-Wignored-qualifiers]

     operator const uint8_t() const       { return **this; }

                          ^

    C:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src/EEPROM.h:92:26: warning: type qualifiers ignored on function return type [-Wignored-qualifiers]

     operator const int() const          { return index; }

                      ^

    C:\Users\Astro\Documents\focuser\Focuserv250_DRV8825_HW203_F\Focuserv250_DRV8825_HW203_F.ino:476:6: warning: unused parameter 'command' [-Wunused-parameter]

    void processCommand(String command)

      ^

    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "C:\Users\Astro\Documents\Arduino\libraries\OneWire-master\OneWire.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\OneWire-master\OneWire.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "C:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master\DallasTemperature.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\Arduino-Temperature-Control-Library-master\DallasTemperature.cpp.o"
    C:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master\DallasTemperature.cpp:808:6: warning: unused parameter 'deviceAddress' [-Wunused-parameter]

    void DallasTemperature::defaultAlarmHandler(const uint8_t* deviceAddress){}

      ^

    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "C:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src\Wire.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\Wire\Wire.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-gcc" -c -g -Os -Wall -Wextra -std=gnu11 -ffunction-sections -fdata-sections -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "C:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src\utility\twi.c" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\Wire\utility\twi.c.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\utility" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\FastIO.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\FastIO.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\utility" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\I2CIO.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\I2CIO.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\utility" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\LCD.cpp.o"
    In file included from C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.cpp:46:0:

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:89:20: warning: unused parameter 'uSec' [-Wunused-parameter]

    inline static void waitUsec ( uint16_t uSec )

                    ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:486:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklightPin ( uint8_t value, t_backlighPol pol ) { };

             ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:486:17: warning: unused parameter 'pol' [-Wunused-parameter]

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:505:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklight ( uint8_t value ) { };

             ^

    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\utility" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\LiquidCrystal.cpp.o"
    In file included from C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal.h:32:0,

                 from C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal.cpp:38:

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:89:20: warning: unused parameter 'uSec' [-Wunused-parameter]

    inline static void waitUsec ( uint16_t uSec )

                    ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:486:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklightPin ( uint8_t value, t_backlighPol pol ) { };

             ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:486:17: warning: unused parameter 'pol' [-Wunused-parameter]

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:505:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklight ( uint8_t value ) { };

             ^

    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\utility" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_I2C.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\LiquidCrystal_I2C.cpp.o"
    In file included from C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_I2C.h:35:0,

                 from C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_I2C.cpp:37:

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:89:20: warning: unused parameter 'uSec' [-Wunused-parameter]

    inline static void waitUsec ( uint16_t uSec )

                    ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:486:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklightPin ( uint8_t value, t_backlighPol pol ) { };

             ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:486:17: warning: unused parameter 'pol' [-Wunused-parameter]

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:505:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklight ( uint8_t value ) { };

             ^

    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\utility" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_I2C_ByVac.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\LiquidCrystal_I2C_ByVac.cpp.o"
    In file included from C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_I2C_ByVac.h:38:0,

                 from C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_I2C_ByVac.cpp:34:

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:89:20: warning: unused parameter 'uSec' [-Wunused-parameter]

    inline static void waitUsec ( uint16_t uSec )

                    ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:486:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklightPin ( uint8_t value, t_backlighPol pol ) { };

             ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:486:17: warning: unused parameter 'pol' [-Wunused-parameter]

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:505:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklight ( uint8_t value ) { };

             ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_I2C_ByVac.cpp: In constructor 'LiquidCrystal_I2C_ByVac::LiquidCrystal_I2C_ByVac(uint8_t)':

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_I2C_ByVac.cpp:41:14: warning: statement has no effect [-Wunused-value]

    _polarity == NEGATIVE;

          ^

    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\utility" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SI2C.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\LiquidCrystal_SI2C.cpp.o"
    In file included from C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SI2C.h:38:0,

                 from C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SI2C.cpp:40:

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:89:20: warning: unused parameter 'uSec' [-Wunused-parameter]

    inline static void waitUsec ( uint16_t uSec )

                    ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:486:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklightPin ( uint8_t value, t_backlighPol pol ) { };

             ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:486:17: warning: unused parameter 'pol' [-Wunused-parameter]

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:505:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklight ( uint8_t value ) { };

             ^

    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\utility" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\LiquidCrystal_SR.cpp.o"
    In file included from C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR.h:84:0,

                 from C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR.cpp:90:

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:89:20: warning: unused parameter 'uSec' [-Wunused-parameter]

    inline static void waitUsec ( uint16_t uSec )

                    ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:486:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklightPin ( uint8_t value, t_backlighPol pol ) { };

             ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:486:17: warning: unused parameter 'pol' [-Wunused-parameter]

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:505:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklight ( uint8_t value ) { };

             ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR.cpp:110:6: warning: unused parameter 'lines' [-Wunused-parameter]

    void LiquidCrystal_SR::init(uint8_t srdata, uint8_t srclock, uint8_t enable, 

      ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR.cpp:110:6: warning: unused parameter 'font' [-Wunused-parameter]

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR.cpp:202:6: warning: unused parameter 'pin' [-Wunused-parameter]

    void LiquidCrystal_SR::setBacklightPin ( uint8_t pin, t_backlighPol pol )

      ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR.cpp:202:6: warning: unused parameter 'pol' [-Wunused-parameter]

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR.cpp:207:6: warning: unused parameter 'mode' [-Wunused-parameter]

    void LiquidCrystal_SR::setBacklight ( uint8_t mode ) 

      ^

    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\utility" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR1W.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\LiquidCrystal_SR1W.cpp.o"
    In file included from C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR1W.cpp:35:0:

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR1W.h:157:1: warning: multi-line comment [-Wcomment]

    // | | 0.1uF | \

    ^

    In file included from C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR1W.h:266:0,

                 from C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR1W.cpp:35:

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:89:20: warning: unused parameter 'uSec' [-Wunused-parameter]

    inline static void waitUsec ( uint16_t uSec )

                    ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:486:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklightPin ( uint8_t value, t_backlighPol pol ) { };

             ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:486:17: warning: unused parameter 'pol' [-Wunused-parameter]

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:505:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklight ( uint8_t value ) { };

             ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR1W.cpp:50:6: warning: unused parameter 'lines' [-Wunused-parameter]

    void LiquidCrystal_SR1W::init(uint8_t srdata, t_sr1w_circuitType circuitType, t_backlighPol blpol, uint8_t lines, uint8_t font)

      ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR1W.cpp:50:6: warning: unused parameter 'font' [-Wunused-parameter]

    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\utility" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR2W.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\LiquidCrystal_SR2W.cpp.o"
    In file included from C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR2W.h:125:0,

                 from C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR2W.cpp:32:

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:89:20: warning: unused parameter 'uSec' [-Wunused-parameter]

    inline static void waitUsec ( uint16_t uSec )

                    ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:486:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklightPin ( uint8_t value, t_backlighPol pol ) { };

             ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:486:17: warning: unused parameter 'pol' [-Wunused-parameter]

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:505:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklight ( uint8_t value ) { };

             ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR2W.cpp:48:6: warning: unused parameter 'lines' [-Wunused-parameter]

    void LiquidCrystal_SR2W::init(uint8_t srdata, uint8_t srclock, t_backlighPol blpol, uint8_t lines, uint8_t font)

      ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR2W.cpp:48:6: warning: unused parameter 'font' [-Wunused-parameter]

    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\utility" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR3W.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\LiquidCrystal_SR3W.cpp.o"
    In file included from C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR3W.h:62:0,

                 from C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LiquidCrystal_SR3W.cpp:77:

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:89:20: warning: unused parameter 'uSec' [-Wunused-parameter]

    inline static void waitUsec ( uint16_t uSec )

                    ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:486:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklightPin ( uint8_t value, t_backlighPol pol ) { };

             ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:486:17: warning: unused parameter 'pol' [-Wunused-parameter]

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\LCD.h:505:17: warning: unused parameter 'value' [-Wunused-parameter]

    virtual void setBacklight ( uint8_t value ) { };

             ^

    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\utility" "C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\SI2CIO.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\SI2CIO.cpp.o"
    In file included from C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\SI2CIO.cpp:51:0:

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\SoftI2CMaster.h:271:7: warning: unused parameter 'addr' [-Wunused-parameter]

    bool i2c_start(uint8_t addr)

       ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\SoftI2CMaster.h:289:7: warning: unused parameter 'addr' [-Wunused-parameter]

    bool i2c_rep_start(uint8_t addr)

       ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\SoftI2CMaster.h:314:7: warning: unused parameter 'addr' [-Wunused-parameter]

    void i2c_start_wait(uint8_t addr)

       ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\SoftI2CMaster.h:361:6: warning: unused parameter 'value' [-Wunused-parameter]

    bool i2c_write(uint8_t value)

      ^

    C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal\SoftI2CMaster.h:438:9: warning: unused parameter 'last' [-Wunused-parameter]

    uint8_t i2c_read(bool last)

         ^

    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\Astro\Documents\Arduino\libraries\OneWire-master" "-IC:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal" "-IC:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM\src" "-IC:\Users\Astro\Documents\Arduino\libraries\Bounce2-master" "C:\Users\Astro\Documents\Arduino\libraries\Bounce2-master\Bounce2.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\Bounce2-master\Bounce2.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-gcc" -c -g -x assembler-with-cpp -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\wiring_pulse.S" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\wiring_pulse.S.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-gcc" -c -g -Os -Wall -Wextra -std=gnu11 -ffunction-sections -fdata-sections -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\WInterrupts.c" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\WInterrupts.c.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-gcc" -c -g -Os -Wall -Wextra -std=gnu11 -ffunction-sections -fdata-sections -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\hooks.c" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\hooks.c.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-gcc" -c -g -Os -Wall -Wextra -std=gnu11 -ffunction-sections -fdata-sections -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\wiring.c" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\wiring.c.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-gcc" -c -g -Os -Wall -Wextra -std=gnu11 -ffunction-sections -fdata-sections -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\wiring_analog.c" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\wiring_analog.c.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-gcc" -c -g -Os -Wall -Wextra -std=gnu11 -ffunction-sections -fdata-sections -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\wiring_digital.c" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\wiring_digital.c.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-gcc" -c -g -Os -Wall -Wextra -std=gnu11 -ffunction-sections -fdata-sections -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\wiring_pulse.c" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\wiring_pulse.c.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-gcc" -c -g -Os -Wall -Wextra -std=gnu11 -ffunction-sections -fdata-sections -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\wiring_shift.c" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\wiring_shift.c.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\CDC.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\CDC.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\HardwareSerial.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\HardwareSerial.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\HardwareSerial0.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\HardwareSerial0.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\HardwareSerial1.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\HardwareSerial1.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\HardwareSerial2.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\HardwareSerial2.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\HardwareSerial3.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\HardwareSerial3.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\IPAddress.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\IPAddress.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\PluggableUSB.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\PluggableUSB.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\Print.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\Print.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\Stream.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\Stream.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\Tone.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\Tone.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\USBCore.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\USBCore.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\WMath.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\WMath.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\WString.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\WString.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\abi.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\abi.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\main.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\main.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -Wall -Wextra -std=gnu++11 -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10608 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR "-IC:\Program Files\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Program Files\Arduino\hardware\arduino\avr\cores\arduino\new.cpp" -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\new.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\wiring_pulse.S.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\WInterrupts.c.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\hooks.c.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\wiring.c.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\wiring_analog.c.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\wiring_digital.c.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\wiring_pulse.c.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\wiring_shift.c.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\CDC.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\HardwareSerial.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\HardwareSerial0.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\HardwareSerial1.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\HardwareSerial2.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\HardwareSerial3.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\IPAddress.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\PluggableUSB.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\Print.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\Stream.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\Tone.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\USBCore.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\WMath.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\WString.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\abi.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\main.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-ar" rcs "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\core.a" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\core\new.cpp.o"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-gcc" -Wall -Wextra -Os -Wl,--gc-sections -mmcu=atmega328p -o "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp/Focuserv250_DRV8825_HW203_F.ino.elf" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\sketch\Focuserv250_DRV8825_HW203_F.ino.cpp.o" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\OneWire-master\OneWire.cpp.o" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\Arduino-Temperature-Control-Library-master\DallasTemperature.cpp.o" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\Wire\Wire.cpp.o" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\Wire\utility\twi.c.o" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\FastIO.cpp.o" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\I2CIO.cpp.o" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\LCD.cpp.o" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\LiquidCrystal.cpp.o" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\LiquidCrystal_I2C.cpp.o" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\LiquidCrystal_I2C_ByVac.cpp.o" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\LiquidCrystal_SI2C.cpp.o" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\LiquidCrystal_SR.cpp.o" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\LiquidCrystal_SR1W.cpp.o" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\LiquidCrystal_SR2W.cpp.o" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\LiquidCrystal_SR3W.cpp.o" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\NewliquidCrystal\SI2CIO.cpp.o" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp\libraries\Bounce2-master\Bounce2.cpp.o" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp/core\core.a" "-LC:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp" -lm
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-objcopy" -O ihex -j .eeprom --set-section-flags=.eeprom=alloc,load --no-change-warnings --change-section-lma .eeprom=0 "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp/Focuserv250_DRV8825_HW203_F.ino.elf" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp/Focuserv250_DRV8825_HW203_F.ino.eep"
    "C:\Program Files\Arduino\hardware\tools\avr/bin/avr-objcopy" -O ihex -R .eeprom "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp/Focuserv250_DRV8825_HW203_F.ino.elf" "C:\Users\Astro\AppData\Local\Temp\buildfe528e5b9aef1d19552c6670358e23fe.tmp/Focuserv250_DRV8825_HW203_F.ino.hex"
    Using library OneWire-master at version 2.3.2 in folder: C:\Users\Astro\Documents\Arduino\libraries\OneWire-master
    Using library Arduino-Temperature-Control-Library-master at version 3.7.7 in folder: C:\Users\Astro\Documents\Arduino\libraries\Arduino-Temperature-Control-Library-master
    Using library Wire at version 1.0 in folder: C:\Program Files\Arduino\hardware\arduino\avr\libraries\Wire
    Using library NewliquidCrystal in folder: C:\Users\Astro\Documents\Arduino\libraries\NewliquidCrystal (legacy)
    Using library EEPROM at version 2.0 in folder: C:\Program Files\Arduino\hardware\arduino\avr\libraries\EEPROM
    Using library Bounce2-master at version 2.21 in folder: C:\Users\Astro\Documents\Arduino\libraries\Bounce2-master

    Sketch uses 23,830 bytes (77%) of program storage space. Maximum is 30,720 bytes.
    Global variables use 973 bytes (47%) of dynamic memory, leaving 1,075 bytes for local variables. Maximum is 2,048 bytes.

     

  • chris dillon

    chris dillon - 2017-03-26

    is the problem it being a 20 position 4 line screen rather than a 1602 screen

     

  • brownrb

    brownrb - 2017-03-26

    Nope I think that is highly unlikely as the same lcd library is used for both. You should not be getting any compile warnings at all, this seems to point to your configuration/installation and library files.

     

  • brownrb

    brownrb - 2017-03-26

    This code u can use for DRV8825_HW203_F with a LCD2004 display

     
    Focuserv251_DRV8825_HW203_F.ino
    eepromanything.h

  • brownrb

    brownrb - 2018-01-21

    Chris
    Ignore the warnings - these are from libraries that other authors have not updated.
    The code will still work.

    Sketch uses 23,830 bytes (77%) of program storage space. Maximum is 30,720 bytes.
    Global variables use 973 bytes (47%) of dynamic memory, leaving 1,075 bytes for local variables. Maximum is 2,048 bytes.

    This shows the code has compiled - you just need to send it to the controller -

     

Log in to post a comment.

Want the latest updates on software, tech news, and AI?
Get latest updates about software, tech news, and AI from SourceForge directly in your inbox once a month.