Menu
▾
▴
Re: [Amforth] Issues with a word compile - flash or eeprom write issues
|
From: Jan K. <kro...@ho...> - 2012-05-07 12:21:52
|
Hello, Thanks to all people how have response to my questions. I have now a running system. Special tanks to Chuck and Paulo. I have put the hex files and store them into the directory of avrdude under the arduino. Flashed to the Arduino under the OSX, and voila a working AMForth. Try the same under windows XP and without any error message, nu running AMForth. Cheers, Jan Op 6 mei 2012, om 22:52 heeft Jan Kromhout het volgende geschreven: > Thanks Paulo, > > Could sommething going wrong with the burner? > Can you give me a hint how to do this on the OSX. > I have not yet the experiance. > > Cheers, > > Jan kromhout > Sacharovlaan 3 > 3223HM Hellevoetsluis-NL > > Op 6 mei 2012 om 22:27 heeft Paulo Ferreira <pa...@ke...> het volgende geschreven: > >> >> On 2012/05/06, at 20:00, Erich Waelde wrote: >> >>> Hello, >>> >>> On 05/06/2012 08:12 PM, Jan Kromhout wrote: >>>> >>>> If I understand correctly the best is to buy some bare 328p chips, >>>> and flash them without tatching the lock bits. >>> >>> If fuses and "lock bits" refer to the same thing, then >>> no: "bare chips" and arduino boards are different things. >>> I personally use the following settings on arduino "duemilanove" >>> and "uno" boards >>> >>> MCU=atmega328p >>> # set the fuses according to your MCU >>> LFUSE=0xFF >>> HFUSE=0xD9 >>> # some MCU have this one, see write-fuses target below >>> EFUSE=0x05 >>> >>> The bare chips will run on the internal RC oszillator at 1 (or >>> 8?) MHz, they will ignore the attached crystal, unless you >>> correct the fuse bits. >>> >>> >>> There is a "readme.txt" file in the directory appl/arduino with >>> more information on arduinos. >>> >>> And just to make sure: you are aware, that flashing amforth to >>> an arduino board does remove the arduino bootloader, are you? >>> >>> >>> Cheers, >>> Erich >>> >> >> Yes, those settings work ok with an Arduino Duemilanove (atmega328p). >> >> Here are the command lines for Unix ( in my case OSX) and an usbtiny programmer: >> >> =============================================================================== >> avrdude -c usbtiny -p m328p -e -U flash:w:duemilanove.hex:i -U eeprom:w:duemilanove.eep.hex:i >> >> avrdude -c usbtiny -p m328p -U 'lfuse:w:0xFF:m' >> avrdude -c usbtiny -p m328p -U 'hfuse:w:0xD9:m' >> avrdude -c usbtiny -p m328p -U 'efuse:w:0x05:m' >> >> =========================================================== >> >> Tested with three different arduinos! ( just in case... ) >> >> >> My best regards >> Paulo Ferreira >> >> >> >> >> >> >> >> >> ------------------------------------------------------------------------------ >> Live Security Virtual Conference >> Exclusive live event will cover all the ways today's security and >> threat landscape has changed and how IT managers can respond. Discussions >> will include endpoint security, mobile security and the latest in malware >> threats. http://www.accelacomm.com/jaw/sfrnl04242012/114/50122263/ >> _______________________________________________ >> Amforth-devel mailing list for http://amforth.sf.net/ >> Amf...@li... >> https://lists.sourceforge.net/lists/listinfo/amforth-devel >> > > ------------------------------------------------------------------------------ > Live Security Virtual Conference > Exclusive live event will cover all the ways today's security and > threat landscape has changed and how IT managers can respond. Discussions > will include endpoint security, mobile security and the latest in malware > threats. http://www.accelacomm.com/jaw/sfrnl04242012/114/50122263/ > _______________________________________________ > Amforth-devel mailing list for http://amforth.sf.net/ > Amf...@li... > https://lists.sourceforge.net/lists/listinfo/amforth-devel > |
