Search Results for "smart card encoder"

We moved to https://github.com/frankmorgner/vsmartcard see you there!

...Communicate with the web application over WiFi or ethernet so that it can synchronize (download) sequences, regimens, farm designs, events, and more; upload logs and sensor data; and accept real-time commands. Communicate with the Farmduino to send G and F commands and receive sensor and encoder data. Take photos with a USB or Raspberry Pi camera, and upload the photos to the web application. You must use a .img writing tool to write FarmBot OS onto the microSD card. We recommend downloading and installing balenaEtcher for this purpose.

Betaflight is flight controller software (firmware) used to fly multi-rotor craft and fixed wing craft. This fork differs from Baseflight and Cleanflight in that it focuses on flight performance, leading-edge feature additions, and wide target support. Betaflight supports a wide range of flight controllers with at least an STM32F4 MCU. You can use nearly any piece of modern hardware out there. Full telemetry and high refresh rate for receivers, camera and VTX control, RGB LEDs, and much...

acsccid is a PC/SC driver for Linux/Mac OS X and it supports ACS CCID smart card readers. This library provides a PC/SC IFD handler implementation and communicates with the readers through the PC/SC Lite resource manager (pcscd).

L-ink Card is a smart NFC card with an electronic-ink display built into the card form-factor, aimed at solving everyday pain points of IC cards and giving them a “cooler” interface. The project uses an STM32L0-series microcontroller paired with an ST25DV NFC chip, an e-ink screen, and battery management so the card can display dynamic info while also serving as an NFC tag/card.

iHome is a fully tested Smart Home Automation system using the Raspberry Pi Zero WiFi SBC and Linux OS and has all the functional features of NEST or ECOBEE smart thermostats with the added benefit of full privacy and security at less than half the price! It incorporates MBLogic with algorithms and Modbus coms for HVAC home control via the ionware modbus compatible ionC1 input/output controller board.

...In order to install the Remote Desktop Protocol 8.1 client for Windows 7 SP1,the following updates should be installed in the order shown: KB 2574819: An update is available that adds support for DTLS in Windows 7 SP1 and Windows Server 2008 R2 SP1 KB 2857650: Update that improves the RemoteApp and Desktop Connections features is available for Windows 7 KB 2830477: Update for RemoteApp and Desktop Connections feature is available for Windows KB 2913751: Smart card redirection in remote sessions fails in a Windows 7 SP1-based RDP 8.1 client (Optional) If you experience connection reliability issues after installing KB 2913751, then installing KB 2923545: Update for RDP 8.1 is available for Windows 7 SP1 . I wrote the following program th

...Currently it is possible to communicate with a smartcard directly connected to a Arduino board or connected via a TDA8024T (or compatible chips. e.g. DS8024). All tests have been done with a smart card slot connected directly to the Aruino board. Working: - Activation of asynchronous and synchronous smart cards - Exchanging data with supported Smart card (Sending / Receiving) - Asychron T=0 APDU communication. - Basic sychron communication - ETU calculation from TS byte. - Support class for SLE4432 / SLE4442 / SLE4441 and SLE4440 compatible sychron smartcards. ...

...System is based on a super-loop architecture with check and skip (no-wait) flag event driver system. Supports: UART, SysTick Timer, ADC, SPI, EEPROM, PWM. Also supports: Xilinx FPGA configuration, FPGA SSI interface, smart card reader etc. Tested partially (different modules in each case) on ATMega163/16/32/323/8. Awards CodeProject 2010, Third Prize, Hardware and Device Programming Check the Wiki Page for more details.

Kernel level driver for GEMPLUS's GPR400 Smart Card reader and pcsc ifd interface library.