Search Results for "pin"

Likwid is a simple to install and use toolsuite of command line applications and a library for performance oriented programmers. It works for Intel, AMD, ARMv8 and POWER9 processors on the Linux operating system. There is additional support for Nvidia and AMD GPUs. There is support for ARMv7 and POWER8/9 but there is currently no test machine in our hands to test them properly.

cooling home automation with Arduino(C) and Raspberry(front-end, python). Arduino features: - control PC 4-pin fan with PWM; - measure temperature/humidity with DHT11/22; - adjust fan RPM depend on temperature; - console management; - MQTT serial output. front-end features: - data collection form serial port with MQTT - webUI with for sensors parameters

This sketch makes the Arduino work as a GPIO interface for a computer, where input and output changes are transmitted in run-length encoding. Every time an input pin changes, the Arduino sends the new values of the input pins and the time since the last change. In a similar way, the Arduino can be programmed a sequence of output pin changes, each specified by the new values of the output pins and the time since the previous change. Three application programs are included: the first makes two digital pins act as a TTL-levels UART; the seconds turns the value of the input pins into an image; the third reads codes from infrared remotes with a photodiode and a resistor connected to one of the input pins.

PK2Aux is a library and suite of command-line utilities for using the Microchip PICkit2 programmer device for purposes other than programming (such as the generic pin controls, serial UART, and logic analyzer modes provided by the Windows software).

... * Soil Moisure Sensors are responsible for sensing if the soil of irrigated flowers are wet or not. These sensors are attached to the Sensor Controller Module via slow speed I2C bus. The modules use 2-pin probes and drives them with 4 kHz square wave in order to avoid oxidating the probes. In my implementation I used these small water pumps from Conrad: http://www.conrad.hu/conrad.php?name=Products&pid=539090 The whole system is powered by a 12V / 4A SMPS.

...This application is initially intended to perform certain actions on phones running in Microsoft Lync mode. These actions include: * get device information * get status * sign in using PIN authentication * sign out * reboot * factory reset It also supports performing actions in batch reading data from a CSV file.

************************************************************************************** Steppers redirected to fastio.h from marlin firmware min switches remaped to AUX-3, GBRL uses pin change interrupts simple scheme to allow future porting of next releases command buttons currently disabled Ramps pins config moved to ramps.h cpu_map.h - min switches added GRBL_RAMPS1_4.ino for arduino IDE ************************************************************************************** Ramps 1.4 | GRBL | Test X axis | X axis | OK working Z axis | Y axis for dual motor Y axis | OK working Y axis | Z axis | OK working Ramps AUX-3 pin 3 | min X | OK working Ramps AUX-3 pin 4 | min Y | OK working Ramps AUX-3 pin 5 | min Z | not tested

...ATmega8 uses its 8MHz internal oscillator to reduce hardware (atmega8 no-xtal bootloader is used). The arduino library uses SoftwareSerial internally to communicate ATmega8 via digital pin 6 (only for uno/duemilanove or clone with atmega8/168/328, not for mega & due). Only one wire simplex serial communication at baudrate 9600 is required to communicate with serialLCD module. The library & firmware file is released in public domain as open-source project. Feel free to edit/improve/share it. *** Raspberry Pi python library added. ...

...The code is compiled for the ATmega328p so the supported boards should be: - Arduino Uno - Arduino Duemilanove - Arduino Diecimila - Arduino NG - Arduino Extreme v2 - Arduino Extreme Note: only tested on Arduino Duemilanove No schematics are available yet, but please have a look at the MegasquirtAVR schematics. It is meant for the ATmega128 so not pin compatible.

This is a RGB LED Pin-back Button controlled by an AVR Microcontroller.

ATMEL ATMega1280 based powerful, multifunctional, reliable, expandable and extremely flexible hardware platform for home and industrial processes automation, robotic toys, security systems, education and enjoyment.

A lightweight, simple and easy to use embedded system task scheduler. RataOS is written as a high level C, with a simple HAL & API structure, allowing it to be ported between embedded devices easily.

Project has moved. http://rhyduino.codeplex.com

Input/output (IO) C library exposing a common API for real mode and permission-restricted access to parallel port under Windows, Linux and MS-DOS operative systems. It also allows pin-by-pin port access.

Simple GTK2 application allowing users to manually toggle devices attached to a parallel port device on or off (through the D0->D8 data lines), or run an automatic sequence based on a simple language contained in this program. Good for driving relays, etc

Manage the data pins of the parallel ports (also know as lpt under win).

...The project will help you to connect any arduino motor shield or other H-Bridges to the controller because it is open source and the output pins can therefor be changed as you like. You can upload a better modified version and improove this article by contacting me. With some pin changes you can port this code to other arduino boards.