Search Results for "boot"

...The web interface files are present in the data directory but UI has its own repository ESP3D-WEBUI. Use GPIO2 to the ground to reset all settings in a hard way, 2-6 sec after boot / not before!! Set GPIO2 to ground before boot change boot mode and go to special boot that do not reach FW. Currently, boot takes 10 sec - giving 8 seconds to connect GPIO2 to GND and do a hard recovery for settings. Complete configuration by web browser (Station or Access point) or by Serial/telnet commands.

...At the same time, a detailed configuration introduction is provided for the code generator of MyBatis. . In addition, the book also provides detailed content for cache configuration, plug-in development, Spring, and Spring Boot integration. Finally, we introduce Git and GitHub to let readers understand the MyBatis open source project.

...Obviously, we are leaning very heavily on automation of configuration generation for this release. Half of the tinyNeoPixel speeds have had the assembly routines modified in major ways (there's no more stupid menu for the port), but they are untested. Virtual boot relies on rewriting the vector table, such that the RESET vector points to the bootloader.

Linux Debian 11 Bullseye Rtos 5.10.0-4-rt-amd64 This Bullseye Rtos edition is a powerfull light weight Linux distribution. Within the new generation of software releases worldwide, this may feel like a Linux Distro on steroids. This Distro is build up from the bootstrap. Have Fun and don't forget to hit the bell. Mr. Macron (president) from France is blackmailing his citizens and violating human rights. Therefore France is no longer supported and will have a ip block in the...

Displays the Uptime of the Windows PC on a Overlay

...root name: root root password: root username: tux password: root Instructions: -Download and install 7zip (www.7-zip.org) -Extract files to HDD -Install included VirtualBox (not tested on other versions, but shouldn't matter) -Within VirtualBox make a new machine ----Machine/New --------Name: Savuka / Type: Linux / Version: Other Linux (32-bit) --------1024MB RAM -------- Use Existing virtual drive (point to extracted Savuka.vdi) ---- Machine/Settigns/Display: set video memory to 50 MB, enable 2D and 3D acceleration ---- Machine/Settings/Shared Folders: Create new machine folder. Point to any data directory, folder name: DATA, select Auto-mount. Note: "Folder name" must be 'DATA' in all caps to link on boot Thats it! More Info: www.osmanbilsel.net www.paulnobrega.net

...The processor is a pipelined architecture clocked at 100 MHz in a Cyclone II speed grade -6. Therefore it can be seen as similar to a 486 in real mode. Several peripherals are also implemented in a somewhat minimalistic way, but enough to be able to boot an IBM PCXT compatible bios and MSDOS 6.22. The current implementation is only proven to boot the bios and DOS in simulation. The system is targeted to run on the DE2-70 board. In order to run the system in hardware a SDRAM and SRAM controller need to be added. These are currently in development.

This project is a collection of utilities to boot and flash various TI DaVinci and OMAP processors, including DSP-only, ARM-only, and ARM+DSP devices.

sloadhost: command line options driven utilities to target microcontroller serial boot load protocols. First supported target is the STM32 (Cortex M3 core) These run on Linux and Windows

SDBoot is a complete bootloader solution (MCU side and PC side), free, with source code for AVR MCU chip. It features a checksumed protocol for safe programming.

Universal BootLoader Tool helps you easily recover from a failed rom flash, and is known to turn an free update rom into a full rom. (e.g. from the free WM5 update rom available for hx4700 Pocket PCs on HP.com) Only tested with HP iPAQ Pocket PCs.

This project is for a PE Builder plug-in for the Ext2Fsd software. I decided to develope this solution in order to be able to scan ext2/ext3 partitions using KAV/KIS anti-virus Rescue Disk which is created with PE Builder.

The Affordable BIOS Restoration Tool provides VHDL and C code to recover from failed BIOS upgrades using affordable CPLD's. EEPROM's and Flash chips can be restored with this flash programmer. Interfaces for DIP and tsop packages are being developed.

Overfoldix is a distribution of Linux designed to boot off of a CD and run in a ramdisk, not requiring a Hard Disk Drive. This linux distro is used to help out in the Folding@Home distributed computing project. This is a \'better\' OS for Folding@Home

PROJECT IS DISCUNTINUED This project is about to contain information how to write data like boot loader into various flash devices on diffrent CPUs trough JTAG interface