-
I have Diagnostic protocol listed cars and source code and hardware which want to open a diagnostic company and produce all this one.
Europan Vehicles
-ALFA ROMEO,FIAT,LANCIA (All Models with 3 pin and CAN-BUS)
-AUDI,SEAT,SKODA,VW (All Models with CAN-BUS)
-BMW (All Models with old bmw software)
-CITROEN,PEUGEOT (All Models)
-DACIA,RENAULT (All models with CAN-BUS)
-LAND ROVER.
2009-11-15 00:49:06 UTC by myavuzs
-
I need the dump bin file to get LOGIN CODE from it to be able to perform a key-matching procedure. Immobilizer in my Golf IV is integrated with the dashboard so I dont think I can unsolder the eeprom.
There are a few programs on the net that read the memory dumps and extract pin codes.
Is there software that can dump the contents of the eeprom via a VAG COM CAN OBDII cable? Or would it be...
2009-11-11 10:33:36 UTC by sorsen
-
In theory, yes.
In practice, you'd require
* removal of the EEPROM from the car
* careful handling to avoid static shock
* [93C86](http://www.futurlec.com/Memory/93C86.shtml) reader
* by design, a reader entails
* protoboard physical layer
* passive wiring
* computer parallel port (IEEE-1284)
* computer serial port (RS-232)
* relatively simple (~200 NCSL...
2009-11-11 05:40:42 UTC by grandfather
-
Would it be possible to dump data from EEPROM 93C86 in my car?.
2009-11-10 19:51:42 UTC by sorsen
-
Greetings to all who follow this project.
I would suggest that further general discussion
should take place on the mailing lists because
many people (me included) don't check the forums
very often.
No, freediag is not dead yet, just napping...
2009-10-06 18:17:00 UTC by fenugrec
-
You might try the code in CVS, it is much more recent than v0.3 currently in the downloadable packages.
2009-10-06 18:09:46 UTC by fenugrec
-
Look at the site [http://www.obddiagnostics.com/][1]. I have been using their unit for a number of years now and it seems pretty solid. They have the [pdf for the schematic][2] on for their unit on the site as well as all the [programming information][3] needed to access the unit and pull codes. All the reference information is free.
Not sure all the details of Jeff's project but you might...
2009-10-06 12:19:55 UTC by drider1969
-
Hello everyone,
So I have currently been trying to get Jeff's OBDII interface ( http://www.planetfall.com/cms/content/opendiag-obd-ii-schematics-pcb-layout ) to work with freediag. I have the design all set up currently on a bread board but I having some trouble.
I think the circuit seems to be working correctly but I still get negative results when I go to do a scan. Has anyone else used...
2009-10-06 00:56:46 UTC by smerky
-
Whoops. Wrong section. Sorry everyone.
2009-10-06 00:56:03 UTC by smerky
-
Hello everyone,
So I have currently been trying to get Jeff's OBDII interface ( [http://www.planetfall.com/cms/content/opendiag-obd-ii-schematics-pcb-layout][1] ) to work with freediag. I have the design all set up currently on a bread board but I having some trouble.
I think the circuit seems to be working correctly but I still get negative results when I go to do a scan. Has anyone else...
2009-10-06 00:55:10 UTC by smerky
