Work at SourceForge, help us to make it a better place! We have an immediate need for a Support Technician in our San Francisco or Denver office.

Close

Works ok on the T60!

apallo
2008-03-06
2013-04-16
  • apallo
    apallo
    2008-03-06

    here's my log so you can see:

    [3/5/2008 11:51:15 PM] Current Config:
    [3/5/2008 11:51:15 PM]   Active= 0, Cycle= 5, FanBeep= 1200 30, MaxReadErrors= 10
    [3/5/2008 11:51:15 PM]   IconLevels= 50 55 60, IgnoreSensors= XXX,YYY,ZZZ
    [3/5/2008 11:51:15 PM]   Levels= 47°C -> 0,  50°C -> 3,  55°C -> 4,  60°C -> 7,  70°C -> 0x80

    [3/5/2008 11:54:06 PM] Current Config:
    [3/5/2008 11:54:06 PM]   Active= 0, Cycle= 5, FanBeep= 1200 30, MaxReadErrors= 10
    [3/5/2008 11:54:06 PM]   IconLevels= 50 55 60, IgnoreSensors= XXX,YYY,ZZZ
    [3/5/2008 11:54:06 PM]   Levels= 47°C -> 0,  50°C -> 3,  55°C -> 4,  60°C -> 7,  70°C -> 0x80

    [3/5/2008 11:56:27 PM] Current Config:
    [3/5/2008 11:56:27 PM]   Active= 1, Cycle= 5, FanBeep= 1200 30, MaxReadErrors= 10
    [3/5/2008 11:56:27 PM]   IconLevels= 50 55 60, IgnoreSensors= XXX,YYY,ZZZ
    [3/5/2008 11:56:27 PM]   Levels= 47°C -> 0,  50°C -> 3,  55°C -> 4,  60°C -> 7,  70°C -> 0x80

    [3/5/2008 11:56:33 PM] Fan: 0x80 / Highest: 70°C (42 34 34 70 32 n/a 30 n/a 35 39 39 n/a)
    [3/5/2008 11:56:33 PM] Manual: Set fan control to 0x07, Result: OK
    [3/5/2008 11:57:00 PM] Fan: 0x07 / Highest: 70°C (42 34 34 70 32 n/a 30 n/a 35 39 39 n/a)
    [3/5/2008 11:57:00 PM] Manual: Set fan control to 0x03, Result: OK
    [3/5/2008 11:57:56 PM] Warning: Can't read Status (possible conflict with other software)
    [3/5/2008 11:57:59 PM] Fan: 0x03 / Highest: 70°C (42 34 34 70 32 n/a 30 n/a 35 39 39 n/a)
    [3/5/2008 11:57:59 PM] Manual: Set fan control to 0x07, Result: OK
    [3/5/2008 11:58:38 PM] Fan: 0x07 / Highest: 70°C (42 34 34 70 32 n/a 30 n/a 35 39 39 n/a)
    [3/5/2008 11:58:38 PM] Mode switch: Set fan control to 0x80, Result: OK
    [3/5/2008 11:58:57 PM] Fan: 0x80 / Highest: 70°C (42 34 34 70 32 n/a 30 n/a 35 39 39 n/a)
    [3/5/2008 11:58:57 PM] On close: Set fan control to 0x80, Result: OK

    as you can see, it conflicted with something, but was able to get through eventually!
    good program!

     
    • Florian
      Florian
      2009-03-16

      It works great on my T60, too!
      Thank you very much!