Re: [Svxlink-devel] Transmitter stuck on
Brought to you by:
sm0svx
From: Adi B. <dl...@gm...> - 2014-02-24 07:16:11
|
Hi Chris, did you really wait for 30 seconds after the squelch has been closed? The param IDLE_TIMEOUT=30 keeps the TX up for this time after the last squelch-closed event has been detected. The bell sound you hear is the idle-sound, you can deactivate it by comment out the line IDLE_SOUND_INTERVAL=3000 73's de Adi, DL1HRC Am 24.02.2014 03:34, schrieb Chris Wilson: > Hello Everyone, > > I just setup svxlink, and i've been trying it out...I have it hooked > into a tx/rx radio pair and everything seems to be working however > after the initial keyup the repeater stays keyed up and plays a bell > sound every few seconds. > > I have my repeater setup (isolated) through my serial port RTSDTR/DCD > (Active Low), all the signals seem to be fine, COR is detected and PTT > works just fine, id's play and audio is repeated...svxlink is just > keeping the TX keyed up after COR is dropped... > > any ideas? I cant seem to find much info out there on this specific > issue. below is my svxlink.conf. > > Thanks! > > Chris W / N0CSW > > [GLOBAL] > MODULE_PATH=/usr/lib/svxlink > LOGICS=RepeaterLogic > CFG_DIR=svxlink.d > TIMESTAMP_FORMAT="%c" > CARD_SAMPLE_RATE=48000 > > [RepeaterLogic] > TYPE=Repeater > RX=Rx1 > TX=Tx1 > MODULES=ModuleHelp,ModuleParrot,ModuleTclVoiceMail > CALLSIGN=N0CSW > SHORT_IDENT_INTERVAL=10 > LONG_IDENT_INTERVAL=60 > #IDENT_ONLY_AFTER_TX=4 > #EXEC_CMD_ON_SQL_CLOSE=500 > EVENT_HANDLER=/usr/share/svxlink/events.tcl > DEFAULT_LANG=en_US > RGR_SOUND_DELAY=0 > REPORT_CTCSS=136.5 > #TX_CTCSS=SQL_OPEN > MACROS=Macros > #SEL5_MACRO_RANGE=03400,03499 > FX_GAIN_NORMAL=0 > FX_GAIN_LOW=-12 > #QSO_RECORDER=8:QsoRecorder > #NO_REPEAT=1 > IDLE_TIMEOUT=30 > #OPEN_ON_1750=1000 > #OPEN_ON_CTCSS=136:2000 > #OPEN_ON_DTMF=* > OPEN_ON_SQL=50 > #OPEN_ON_SEL5=01234 > #OPEN_SQL_FLANK=OPEN > #OPEN_ON_SQL_AFTER_RPT_CLOSE=10 > IDLE_SOUND_INTERVAL=3000 > #SQL_FLAP_SUP_MIN_TIME=1000 > #SQL_FLAP_SUP_MAX_COUNT=10 > #ACTIVATE_MODULE_ON_LONG_CMD=4:EchoLink > #IDENT_NAG_TIMEOUT=15 > #IDENT_NAG_MIN_TIME=2000 > #ONLINE_CMD=998877 > > [Macros] > 1=EchoLink:9999# > 9=Parrot:0123456789# > 03400=EchoLink:9999# > > [Rx1] > TYPE=Local > AUDIO_DEV=alsa:plughw:0 > AUDIO_CHANNEL=0 > SQL_DET=SERIAL > SQL_START_DELAY=0 > SQL_DELAY=0 > SQL_HANGTIME=2000 > #SQL_EXTENDED_HANGTIME=1000 > #SQL_EXTENDED_HANGTIME_THRESH=15 > #SQL_TIMEOUT=600 > VOX_FILTER_DEPTH=20 > VOX_THRESH=1000 > #CTCSS_MODE=2 > CTCSS_FQ=136.5 > #CTCSS_SNR_OFFSET=0 > #CTCSS_OPEN_THRESH=15 > #CTCSS_CLOSE_THRESH=9 > #CTCSS_BPF_LOW=60 > #CTCSS_BPF_HIGH=270 > SERIAL_PORT=/dev/ttyS0 > SERIAL_PIN=DCD:CLEAR > #SERIAL_SET_PINS=DTR!RTS > #EVDEV_DEVNAME=/dev/input/by-id/usb-SYNIC_SYNIC_Wireless_Audio-event-if03 > #EVDEV_OPEN=1,163,1 > #EVDEV_CLOSE=1,163,0 > #GPIO_SQL_PIN=gpio30 > #SIGLEV_DET=TONE > SIGLEV_SLOPE=1 > SIGLEV_OFFSET=0 > #TONE_SIGLEV_MAP=100,84,60,50,37,32,28,23,19,8 > SIGLEV_OPEN_THRESH=30 > SIGLEV_CLOSE_THRESH=10 > DEEMPHASIS=0 > #SQL_TAIL_ELIM=300 > #PREAMP=6 > PEAK_METER=1 > DTMF_DEC_TYPE=INTERNAL > DTMF_MUTING=1 > DTMF_HANGTIME=100 > #DTMF_SERIAL=/dev/ttyS0 > #DTMF_MAX_FWD_TWIST=8 > #DTMF_MAX_REV_TWIST=4 > #1750_MUTING=1 > #SEL5_DEC_TYPE=INTERNAL > #SEL5_TYPE=ZVEI1 > > [Tx1] > TYPE=Local > AUDIO_DEV=alsa:plughw:0 > AUDIO_CHANNEL=0 > PTT_PORT=/dev/ttyS0 > PTT_PIN=DTRRTS > #SERIAL_SET_PINS=DTR!RTS > PTT_HANGTIME=50 > TIMEOUT=300 > TX_DELAY=500 > #CTCSS_FQ=136.5 > #CTCSS_LEVEL=9 > PREEMPHASIS=0 > DTMF_TONE_LENGTH=100 > DTMF_TONE_SPACING=50 > DTMF_TONE_AMP=-18 > > Output from SVXLink: > SvxLink v1.3.0 (Feb 23 2014) Copyright (C) 2003-2013 Tobias Blomberg / > SM0SVX > > SvxLink comes with ABSOLUTELY NO WARRANTY. This is free software, and > you are > welcome to redistribute it in accordance with the terms and conditions > in the > GNU GPL (General Public License) version 2 or later. > > Using configuration file: /etc/svxlink/svxlink.conf > --- Using sample rate 48000Hz > > Starting logic: RepeaterLogic > Loading RX: Rx1 > Loading TX: Tx1 > Loading module "ModuleHelp" into logic "RepeaterLogic" > Module Help v1.0.0 starting... > Loading module "ModuleParrot" into logic "RepeaterLogic" > Module Parrot v1.1.0 starting... > Loading module "ModuleTclVoiceMail" into logic "RepeaterLogic" > Module Tcl v1.0.0 starting... > RepeaterLogic: Event handler script successfully loaded. > Rx1: The squelch is OPEN (4.98098) > Rx1: The squelch is CLOSED (0.766182) > Tx1: Turning the transmitter ON > *^^^ Transmitter never goes OFF* > > > ------------------------------------------------------------------------------ > Flow-based real-time traffic analytics software. Cisco certified tool. > Monitor traffic, SLAs, QoS, Medianet, WAAS etc. with NetFlow Analyzer > Customize your own dashboards, set traffic alerts and generate reports. > Network behavioral analysis & security monitoring. All-in-one tool. > http://pubads.g.doubleclick.net/gampad/clk?id=126839071&iu=/4140/ostg.clktrk > > > _______________________________________________ > Svxlink-devel mailing list > Svx...@li... > https://lists.sourceforge.net/lists/listinfo/svxlink-devel |