Menu
▾
▴
Re: [smartmontools-support] ST650211CF Broken SMART?
|
From: Weedy <wee...@gm...> - 2008-11-10 02:31:29
|
because it's the only thing I have on hand and replacing it would be a ton of work. Justin Piszcz wrote: > A really old 5GiB Seagate HDD, why bother with it? > http://www.overstock.com/Electronics/5GB-Seagate-ST1-Series-Hard-Drive-Refurb/2925351/product.html?cid=123620&fp=F&ci_src=14110944&ci_sku=11092561 > > > On Sat, 8 Nov 2008, Weedy wrote: > >> If I'm reading this right this drive should have burst into flames or >> something. >> So far I've had no trouble at all with it. So do I ignore SMART or >> junk it? >> >> >> # smartctl -d ata --all -T permissive /dev/sda >> smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce >> Allen >> Home page is http://smartmontools.sourceforge.net/ >> >> === START OF INFORMATION SECTION === >> Device Model: ST650211CF >> Serial Number: 3ME15JQ1 >> Firmware Version: 3.04 >> User Capacity: 5,000,970,240 bytes >> Device is: Not in smartctl database [for details use: -P showall] >> ATA Version is: 1 >> ATA Standard is: Exact ATA specification draft version not indicated >> Local Time is: Sat Nov 8 10:54:08 2008 EST >> SMART is only available in ATA Version 3 Revision 3 or greater. >> We will try to proceed in spite of this. >> SMART support is: Unavailable - Packet Interface Devices [this device: >> Write-once (optical disk)] don't support ATA SMART >> SMART support is: Available - device has SMART capability. >> SMART support is: Enabled >> >> === START OF READ SMART DATA SECTION === >> SMART overall-health self-assessment test result: FAILED! >> Drive failure expected in less than 24 hours. SAVE ALL DATA. >> See vendor-specific Attribute list for failed Attributes. >> >> General SMART Values: >> Offline data collection status: (0x82) Offline data collection activity >> was completed without error. >> Auto Offline Data Collection: >> Enabled. >> Self-test execution status: ( 0) The previous self-test routine >> completed >> without error or no self-test >> has ever >> been run. >> Total time to complete Offline >> data collection: ( 420) seconds. >> Offline data collection >> capabilities: (0x5b) SMART execute Offline immediate. >> Auto Offline data collection >> on/off support. >> Suspend Offline collection >> upon new >> command. >> Offline surface scan supported. >> Self-test supported. >> No Conveyance Self-test >> supported. >> Selective Self-test supported. >> SMART capabilities: (0x0003) Saves SMART data before entering >> power-saving mode. >> Supports SMART auto save timer. >> Error logging capability: (0x01) Error logging supported. >> No General Purpose Logging >> support. >> Short self-test routine >> recommended polling time: ( 1) minutes. >> Extended self-test routine >> recommended polling time: ( 28) minutes. >> >> SMART Attributes Data Structure revision number: 10 >> Vendor Specific SMART Attributes with Thresholds: >> ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE >> UPDATED WHEN_FAILED RAW_VALUE >> 1 Raw_Read_Error_Rate 0x000f 056 050 025 Pre-fail >> Always - 59402560 >> 3 Spin_Up_Time 0x0003 100 100 000 Pre-fail >> Always - 0 >> 4 Start_Stop_Count 0x0032 091 091 020 Old_age >> Always - 9686 >> 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail >> Always - 1 >> 7 Seek_Error_Rate 0x000f 024 019 030 Pre-fail >> Always FAILING_NOW 72039490298986 >> 9 Power_On_Hours 0x0032 100 100 000 Old_age >> Always - 41 >> 10 Spin_Retry_Count 0x0012 100 081 000 Old_age >> Always - 0 >> 12 Power_Cycle_Count 0x0032 091 091 020 Old_age >> Always - 9696 >> 192 Power-Off_Retract_Count 0x0032 001 001 000 Old_age >> Always - 4294961235 >> 193 Load_Cycle_Count 0x0032 092 092 000 Old_age >> Always - 17639 >> 194 Temperature_Celsius 0x0022 024 046 000 Old_age >> Always - 24 (Lifetime Min/Max 8/46) >> 195 Hardware_ECC_Recovered 0x001a 100 253 000 Old_age >> Always - 0 >> 197 Current_Pending_Sector 0x0012 100 100 000 Old_age >> Always - 2 >> 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age >> Offline - 0 >> 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age >> Always - 0 >> 200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age >> Offline - 0 >> 202 TA_Increase_Count 0x0032 100 253 000 Old_age >> Always - 0 >> >> SMART Error Log Version: 1 >> ATA Error Count: 31 (device log contains only the most recent five >> errors) >> CR = Command Register [HEX] >> FR = Features Register [HEX] >> SC = Sector Count Register [HEX] >> SN = Sector Number Register [HEX] >> CL = Cylinder Low Register [HEX] >> CH = Cylinder High Register [HEX] >> DH = Device/Head Register [HEX] >> DC = Device Command Register [HEX] >> ER = Error register [HEX] >> ST = Status register [HEX] >> Powered_Up_Time is measured from power on, and printed as >> DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, >> SS=sec, and sss=millisec. It "wraps" after 49.710 days. >> >> Error 31 occurred at disk power-on lifetime: 24 hours (1 days + 0 hours) >> When the command that caused the error occurred, the device was active >> or idle. >> >> After command completion occurred, registers were: >> ER ST SC SN CL CH DH >> -- -- -- -- -- -- -- >> 40 51 0f f0 a2 00 e0 >> >> Commands leading to the command that caused the error were: >> CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name >> -- -- -- -- -- -- -- -- ---------------- -------------------- >> e0 00 10 00 10 a1 00 00 00:00:00.009 STANDBY IMMEDIATE >> e0 00 10 00 e0 a0 00 00 00:00:00.016 STANDBY IMMEDIATE >> e0 00 01 00 89 00 00 00 00:00:00.000 STANDBY IMMEDIATE >> e0 00 01 00 89 00 00 00 00:00:00.033 STANDBY IMMEDIATE >> e0 00 0b 00 7e 00 00 00 00:00:00.000 STANDBY IMMEDIATE >> >> Error 30 occurred at disk power-on lifetime: 24 hours (1 days + 0 hours) >> When the command that caused the error occurred, the device was active >> or idle. >> >> After command completion occurred, registers were: >> ER ST SC SN CL CH DH >> -- -- -- -- -- -- -- >> 40 51 0f f0 a2 00 e0 >> >> Commands leading to the command that caused the error were: >> CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name >> -- -- -- -- -- -- -- -- ---------------- -------------------- >> e0 00 10 00 10 a1 00 00 00:00:00.009 STANDBY IMMEDIATE >> e0 00 10 00 e0 a0 00 00 00:00:00.016 STANDBY IMMEDIATE >> e0 00 01 00 89 00 00 00 00:00:00.000 STANDBY IMMEDIATE >> e0 00 01 00 89 00 00 00 00:00:00.033 STANDBY IMMEDIATE >> e0 00 0b 00 7e 00 00 00 00:00:00.000 STANDBY IMMEDIATE >> >> Error 29 occurred at disk power-on lifetime: 24 hours (1 days + 0 hours) >> When the command that caused the error occurred, the device was active >> or idle. >> >> After command completion occurred, registers were: >> ER ST SC SN CL CH DH >> -- -- -- -- -- -- -- >> 40 51 0f f0 a2 00 e0 >> >> Commands leading to the command that caused the error were: >> CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name >> -- -- -- -- -- -- -- -- ---------------- -------------------- >> e0 00 10 00 10 a1 00 00 00:00:00.009 STANDBY IMMEDIATE >> e0 00 10 00 e0 a0 00 00 00:00:00.016 STANDBY IMMEDIATE >> e0 00 01 00 89 00 00 00 00:00:00.000 STANDBY IMMEDIATE >> e0 00 01 00 89 00 00 00 00:00:00.033 STANDBY IMMEDIATE >> e0 00 0b 00 7e 00 00 00 00:00:00.000 STANDBY IMMEDIATE >> >> Error 28 occurred at disk power-on lifetime: 24 hours (1 days + 0 hours) >> When the command that caused the error occurred, the device was active >> or idle. >> >> After command completion occurred, registers were: >> ER ST SC SN CL CH DH >> -- -- -- -- -- -- -- >> 40 51 0f f0 a2 00 e0 >> >> Commands leading to the command that caused the error were: >> CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name >> -- -- -- -- -- -- -- -- ---------------- -------------------- >> e0 00 10 00 10 a1 00 00 00:00:00.008 STANDBY IMMEDIATE >> e0 00 10 00 e0 a0 00 00 00:00:00.016 STANDBY IMMEDIATE >> e0 00 01 00 89 00 00 00 00:00:00.000 STANDBY IMMEDIATE >> e0 00 01 00 89 00 00 00 00:00:00.033 STANDBY IMMEDIATE >> e0 00 0b 00 7e 00 00 00 00:00:00.000 STANDBY IMMEDIATE >> >> Error 27 occurred at disk power-on lifetime: 24 hours (1 days + 0 hours) >> When the command that caused the error occurred, the device was active >> or idle. >> >> After command completion occurred, registers were: >> ER ST SC SN CL CH DH >> -- -- -- -- -- -- -- >> 40 51 0f f0 a2 00 e0 >> >> Commands leading to the command that caused the error were: >> CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name >> -- -- -- -- -- -- -- -- ---------------- -------------------- >> e0 00 10 00 10 a1 00 00 00:00:00.009 STANDBY IMMEDIATE >> e0 00 10 00 e0 a0 00 00 00:00:00.016 STANDBY IMMEDIATE >> e0 00 01 00 89 00 00 00 00:00:00.000 STANDBY IMMEDIATE >> e0 00 01 00 89 00 00 00 00:00:00.033 STANDBY IMMEDIATE >> e0 00 0b 00 7e 00 00 00 00:00:00.000 STANDBY IMMEDIATE >> >> SMART Self-test log structure revision number 1 >> Num Test_Description Status Remaining >> LifeTime(hours) LBA_of_first_error >> # 1 Extended offline Completed without error 00% >> 40 - >> >> Warning! SMART Selective Self-Test Log Structure error: invalid SMART >> checksum. >> SMART Selective self-test log data structure revision number 1 >> SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS >> 1 0 0 Not_testing >> 2 0 0 Not_testing >> 3 0 0 Not_testing >> 4 0 0 Not_testing >> 5 0 0 Not_testing >> Selective self-test flags (0x0): >> After scanning selected spans, do NOT read-scan remainder of disk. >> If Selective self-test is pending on power-up, resume after 0 minute >> delay. >> >> >> ------------------------------------------------------------------------- >> >> This SF.Net email is sponsored by the Moblin Your Move Developer's >> challenge >> Build the coolest Linux based applications with Moblin SDK & win >> great prizes >> Grand prize is a trip for two to an Open Source event anywhere in the >> world >> http://moblin-contest.org/redirect.php?banner_id=100&url=/ >> _______________________________________________ >> Smartmontools-support mailing list >> Sma...@li... >> https://lists.sourceforge.net/lists/listinfo/smartmontools-support >> |