IOData wn-b11 usbsl

Help
vitreda
2008-09-29
2012-10-06
  • vitreda
    vitreda
    2008-09-29

    i'm using Ubuntu 8.04 and kernel 2.6.24-19-generic. I have Ndiswrapper for WiFi USB adapter IOData WN-B11 USBSL.
    In dmesg i see the following errors when i plugin the adapter.

    [ 410.865011] BUG: unable to handle kernel paging request at virtual address e3e60728
    [ 410.865022] printing eip: e0e35c65 *pde = 00000000
    [ 410.865033] Oops: 0002 [#1] SMP

    Anyway the adapter works properly but i cannot use any USB Pen Drive and removing ndiswrapper (modprobe -r ndiswrapper) or giving lsusb freeze the shell. Anything is ok until i plug the wifi adapter

    I downloaded and recompile the latest 1.53 version but the adapter isn't recognized no more!

    can anybody help me please?

    thanks
    vi3da

    dmesg output: some lines have been removed

    [ 26.668498] uhci_hcd 0000:00:07.2: UHCI Host Controller
    [ 26.669275] uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
    [ 26.669322] uhci_hcd 0000:00:07.2: irq 9, io base 0x0000d400
    [ 26.669680] usb usb1: configuration #1 chosen from 1 choice
    [ 26.669738] hub 1-0:1.0: USB hub found
    [ 26.669754] hub 1-0:1.0: 2 ports detected
    [ 26.673284] 8139too Fast Ethernet driver 0.9.28
    [ 26.771490] ACPI: PCI Interrupt 0000:00:07.3[D] -> Link [LNKD] -> GSI 9 (level, low) -> IRQ 9
    [ 26.771525] uhci_hcd 0000:00:07.3: UHCI Host Controller
    [ 26.771587] uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 2
    [ 26.771626] uhci_hcd 0000:00:07.3: irq 9, io base 0x0000d000
    [ 26.771916] usb usb2: configuration #1 chosen from 1 choice
    [ 26.771971] hub 2-0:1.0: USB hub found
    [ 26.771987] hub 2-0:1.0: 2 ports detected
    [ 26.877458] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
    [ 26.877472] PCI: setting IRQ 10 as level-triggered
    [ 26.877480] ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
    [ 26.878280] eth0: RealTek RTL8139 at 0xa000, 00:50:ba:d1:69:d1, IRQ 10
    [ 26.878287] eth0: Identified 8139 chip type 'RTL-8139B'
    [ 27.970595] Driver 'sd' needs updating - please use bus_type methods
    [ 27.971252] sd 0:0:0:0: [sda] 40031712 512-byte hardware sectors (20496 MB)
    [ 27.971293] sd 0:0:0:0: [sda] Write Protect is off
    [ 27.971299] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [ 27.971344] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 27.971480] sd 0:0:0:0: [sda] 40031712 512-byte hardware sectors (20496 MB)
    [ 27.971505] sd 0:0:0:0: [sda] Write Protect is off
    [ 27.971511] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00

    [ 27.971551] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 27.971566] sda:<4>Driver 'sr' needs updating - please use bus_type methods
    [ 28.600031] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
    [ 28.600047] ata1.00: BMDMA stat 0x64
    [ 28.600062] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
    [ 28.600066] res 51/84:00:07:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
    [ 28.600073] ata1.00: status: { DRDY ERR }
    [ 28.600078] ata1.00: error: { ICRC ABRT }
    [ 28.600138] ata1: soft resetting link
    [ 28.802560] ata1.00: configured for UDMA/66
    [ 28.810195] ata1.01: configured for UDMA/66
    [ 28.810239] ata1: EH complete
    [ 29.440805] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
    [ 29.440821] ata1.00: BMDMA stat 0x64
    [ 29.440837] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
    [ 29.440841] res 51/84:00:07:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
    [ 29.440848] ata1.00: status: { DRDY ERR }
    [ 29.440853] ata1.00: error: { ICRC ABRT }
    [ 29.440912] ata1: soft resetting link
    [ 29.642060] ata1.00: configured for UDMA/66
    [ 29.657673] ata1.01: configured for UDMA/66
    [ 29.657714] ata1: EH complete
    [ 30.281594] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
    [ 30.281609] ata1.00: BMDMA stat 0x64
    [ 30.281624] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
    [ 30.281628] res 51/84:00:07:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
    [ 30.281636] ata1.00: status: { DRDY ERR }
    [ 30.281640] ata1.00: error: { ICRC ABRT }
    [ 30.281699] ata1: soft resetting link
    [ 30.485502] ata1.00: configured for UDMA/66
    [ 30.501171] ata1.01: configured for UDMA/66
    [ 30.501211] ata1: EH complete
    [ 31.133429] ata1.00: limiting speed to UDMA/44:PIO4
    [ 31.133445] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
    [ 31.133454] ata1.00: BMDMA stat 0x64
    [ 31.133468] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
    [ 31.133472] res 51/84:00:07:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
    [ 31.133479] ata1.00: status: { DRDY ERR }
    [ 31.133484] ata1.00: error: { ICRC ABRT }
    [ 31.133542] ata1: soft resetting link
    [ 31.336985] ata1.00: configured for UDMA/44
    [ 31.353788] ata1.01: configured for UDMA/66
    [ 31.353841] ata1: EH complete
    [ 31.367353] sda1
    [ 31.367545] sd 0:0:0:0: [sda] Attached SCSI disk
    [ 31.369353] sd 0:0:0:0: [sda] 40031712 512-byte hardware sectors (20496 MB)
    [ 31.369481] sd 0:0:1:0: [sdb] 78165360 512-byte hardware sectors (40021 MB)
    [ 31.369510] sd 0:0:1:0: [sdb] Write Protect is off
    [ 31.369516] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
    [ 31.369538] sd 0:0:0:0: [sda] Write Protect is off
    [ 31.369544] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [ 31.369600] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 31.369633] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 31.369788] sd 0:0:0:0: [sda] 40031712 512-byte hardware sectors (20496 MB)
    [ 31.369811] sd 0:0:0:0: [sda] Write Protect is off
    [ 31.369817] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [ 31.369855] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 31.369898] sd 0:0:1:0: [sdb] 78165360 512-byte hardware sectors (40021 MB)
    [ 31.369921] sd 0:0:1:0: [sdb] Write Protect is off
    [ 31.369926] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
    [ 31.369963] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 31.369993] sd 0:0:1:0: [sdb] 78165360 512-byte hardware sectors (40021 MB)
    [ 31.370016] sd 0:0:1:0: [sdb] Write Protect is off
    [ 31.370021] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
    [ 31.370059] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 31.370070] sdb: sdb1 sdb2 sdb3
    [ 31.401001] sd 0:0:1:0: [sdb] Attached SCSI disk
    [ 31.430097] sd 0:0:0:0: Attached scsi generic sg0 type 0
    [ 31.430145] sd 0:0:1:0: Attached scsi generic sg1 type 0
    [ 31.430188] sr 1:0:0:0: Attached scsi generic sg2 type 5
    [ 31.430228] scsi 1:0:1:0: Attached scsi generic sg3 type 5
    [ 31.435687] sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
    [ 31.435705] Uniform CD-ROM driver Revision: 3.20
    [ 31.435871] sr 1:0:0:0: Attached scsi CD-ROM sr0
    [ 31.441952] sr1: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
    [ 31.442117] sr 1:0:1:0: Attached scsi CD-ROM sr1
    [ 32.363987] Attempting manual resume
    [ 32.363999] swsusp: Resume From Partition 8:19
    [ 32.364003] PM: Checking swsusp image.
    [ 32.364703] PM: Resume from disk failed.
    [ 32.438935] kjournald starting. Commit interval 5 seconds
    [ 32.438985] EXT3-fs: mounted filesystem with ordered data mode.
    [ 45.539456] ip_tables: (C) 2000-2006 Netfilter Core Team
    [ 45.651830] nf_conntrack version 0.5.0 (8192 buckets, 32768 max)
    [ 48.831692] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    [ 48.997819] Linux agpgart interface v0.102
    [ 49.082125] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
    [ 49.309733] agpgart: Detected VIA Twister-K/KT133x/KM133 chipset
    [ 49.313204] agpgart: AGP aperture is 32M @ 0xfc000000
    [ 49.376469] parport_pc: VIA 686A/8231 detected
    [ 49.376481] parport_pc: probing current configuration
    [ 49.376502] parport_pc: Current parallel port base: 0x378
    [ 49.376587] parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,ECP]
    [ 49.473547] parport_pc: VIA parallel port: io=0x378, irq=7
    [ 56.075928] NVRM: loading NVIDIA Linux x86 Kernel Module 96.43.05 Tue Jan 22 19:36:58 PST 2008
    [ 56.512594] ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
    [ 62.163406] lp0: using parport0 (interrupt-driven).
    [ 62.235115] PPP generic driver version 2.4.2
    [ 62.399404] Adding 979956k swap on /dev/sdb3. Priority:-1 extents:1 across:979956k
    [ 63.064412] EXT3 FS on sdb2, internal journal
    [ 66.306942] No dock devices found.
    [ 67.315752] powernow: No powernow capabilities detected
    [ 68.261599] ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
    [ 68.261619] ata1.01: BMDMA stat 0x64
    [ 68.261636] ata1.01: cmd ca/00:20:38:12:75/00:00:00:00:00/f3 tag 0 dma 16384 out
    [ 68.261640] res 51/84:00:38:12:75/00:00:00:00:00/f3 Emask 0x10 (ATA bus error)
    [ 68.261648] ata1.01: status: { DRDY ERR }
    [ 68.261653] ata1.01: error: { ICRC ABRT }
    [ 68.261711] ata1: soft resetting link
    [ 68.462594] ata1.00: configured for UDMA/44
    [ 68.470250] ata1.01: configured for UDMA/66
    [ 68.470284] ata1: EH complete
    [ 68.470881] sd 0:0:0:0: [sda] 40031712 512-byte hardware sectors (20496 MB)
    [ 68.471417] sd 0:0:0:0: [sda] Write Protect is off
    [ 68.471426] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [ 68.472047] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 68.473121] sd 0:0:1:0: [sdb] 78165360 512-byte hardware sectors (40021 MB)
    [ 68.473490] sd 0:0:1:0: [sdb] Write Protect is off
    [ 68.473499] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
    [ 68.475165] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 68.617660] ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
    [ 68.617673] ata1.01: BMDMA stat 0x64
    [ 68.617689] ata1.01: cmd ca/00:b0:a0:15:75/00:00:00:00:00/f3 tag 0 dma 90112 out
    [ 68.617693] res 51/84:00:a0:15:75/00:00:00:00:00/f3 Emask 0x10 (ATA bus error)
    [ 68.617700] ata1.01: status: { DRDY ERR }
    [ 68.617705] ata1.01: error: { ICRC ABRT }
    [ 68.617761] ata1: soft resetting link
    [ 68.822369] ata1.00: configured for UDMA/44
    [ 68.830053] ata1.01: configured for UDMA/66
    [ 68.830082] ata1: EH complete
    [ 68.855410] sd 0:0:1:0: [sdb] Write Protect is off
    [ 68.855415] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
    [ 68.855456] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 69.562152] ppdev: user-space parallel port driver
    [ 69.892463] NET: Registered protocol family 10
    [ 69.893922] lo: Disabled Privacy Extensions
    [ 70.049049] audit(1222599242.150:2): type=1503 operation="inode_permission" requested_mask="a::" denied_mask="a::" name="/dev/tty" pid=5006 profile="/usr/sbin/cupsd" namespace="default"
    [ 70.151695] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
    [ 70.151712] apm: overridden by ACPI.
    [ 76.280518] Bluetooth: Core ver 2.11
    [ 76.284956] NET: Registered protocol family 31
    [ 76.284971] Bluetooth: HCI device and connection manager initialized
    [ 76.284982] Bluetooth: HCI socket layer initialized
    [ 76.361327] Bluetooth: L2CAP ver 2.9
    [ 76.361342] Bluetooth: L2CAP socket layer initialized
    [ 76.531499] Bluetooth: RFCOMM socket layer initialized
    [ 76.531544] Bluetooth: RFCOMM TTY layer initialized
    [ 76.531549] Bluetooth: RFCOMM ver 1.8
    [ 78.670892] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
    [ 78.671692] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
    [ 78.672374] agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
    [ 127.377255] ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
    [ 127.377278] ata1.01: BMDMA stat 0x64
    [ 127.377294] ata1.01: cmd ca/00:00:a0:ef:31/00:00:00:00:00/f3 tag 0 dma 131072 out
    [ 127.377297] res 51/84:00:a0:ef:31/00:00:00:00:00/f3 Emask 0x10 (ATA bus error)
    [ 127.377305] ata1.01: status: { DRDY ERR }
    [ 127.377310] ata1.01: error: { ICRC ABRT }
    [ 127.377371] ata1: soft resetting link
    [ 127.634917] ata1.00: configured for UDMA/44
    [ 127.642640] ata1.01: configured for UDMA/66
    [ 127.642682] ata1: EH complete
    [ 127.786186] ata1.01: limiting speed to UDMA/44:PIO4
    [ 127.786205] ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
    [ 127.786214] ata1.01: BMDMA stat 0x64
    [ 127.786229] ata1.01: cmd ca/00:00:a0:ef:31/00:00:00:00:00/f3 tag 0 dma 131072 out
    [ 127.786233] res 51/84:00:a0:ef:31/00:00:00:00:00/f3 Emask 0x10 (ATA bus error)
    [ 127.786241] ata1.01: status: { DRDY ERR }
    [ 127.786245] ata1.01: error: { ICRC ABRT }
    [ 127.786300] ata1: soft resetting link
    [ 127.990700] ata1.00: configured for UDMA/44
    [ 127.998392] ata1.01: configured for UDMA/44
    [ 127.998430] ata1: EH complete
    [ 127.998707] sd 0:0:0:0: [sda] 40031712 512-byte hardware sectors (20496 MB)
    [ 151.495859] usb 2-2: new full speed USB device using uhci_hcd and address 2
    [ 151.674008] usb 2-2: configuration #1 chosen from 1 choice
    [ 151.896960] usbcore: registered new interface driver libusual
    [ 152.022960] Initializing USB Mass Storage driver...
    [ 152.050891] scsi2 : SCSI emulation for USB Mass Storage devices
    [ 152.059593] usbcore: registered new interface driver usb-storage
    [ 152.060221] USB Mass Storage support registered.
    [ 152.060971] usb-storage: device found at 2
    [ 152.060984] usb-storage: waiting for device to settle before scanning
    [ 157.057802] usb-storage: device scan complete
    [ 157.061779] scsi 2:0:0:0: Direct-Access Kingston DataTraveler 2.0 1.02 PQ: 0 ANSI: 0 CCS
    [ 157.259865] sd 2:0:0:0: [sdc] 251904 512-byte hardware sectors (129 MB)
    [ 157.264056] sd 2:0:0:0: [sdc] Write Protect is off
    [ 157.264077] sd 2:0:0:0: [sdc] Mode Sense: 23 00 00 00
    [ 157.264084] sd 2:0:0:0: [sdc] Assuming drive cache: write through
    [ 157.278063] sd 2:0:0:0: [sdc] 251904 512-byte hardware sectors (129 MB)
    [ 157.280600] sd 2:0:0:0: [sdc] Write Protect is off
    [ 157.280620] sd 2:0:0:0: [sdc] Mode Sense: 23 00 00 00
    [ 157.280627] sd 2:0:0:0: [sdc] Assuming drive cache: write through
    [ 157.280647] sdc: sdc1
    [ 157.287972] sd 2:0:0:0: [sdc] Attached SCSI removable disk
    [ 157.288079] sd 2:0:0:0: Attached scsi generic sg4 type 0
    [ 219.390882] ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
    [ 219.390939] ata1.01: BMDMA stat 0x64
    [ 219.390956] ata1.01: cmd ca/00:20:d8:c3:21/00:00:00:00:00/f4 tag 0 dma 16384 out
    [ 219.390959] res 51/84:00:d8:c3:21/00:00:00:00:00/f4 Emask 0x10 (ATA bus error)
    [ 219.390967] ata1.01: status: { DRDY ERR }
    [ 219.390972] ata1.01: error: { ICRC ABRT }
    [ 219.391026] ata1: soft resetting link
    [ 219.707368] ata1.00: configured for UDMA/44
    [ 219.723101] ata1.01: configured for UDMA/44
    [ 219.723141] ata1: EH complete
    [ 219.723850] sd 0:0:0:0: [sda] 40031712 512-byte hardware sectors (20496 MB)
    [ 219.724542] sd 0:0:0:0: [sda] Write Protect is off
    [ 219.724675] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [ 219.725545] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 219.866164] ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
    [ 219.866185] ata1.01: BMDMA stat 0x64
    [ 219.866201] ata1.01: cmd ca/00:08:38:c3:45/00:00:00:00:00/f4 tag 0 dma 4096 out
    [ 219.866205] res 51/84:00:38:c3:45/00:00:00:00:00/f4 Emask 0x10 (ATA bus error)
    [ 219.866212] ata1.01: status: { DRDY ERR }
    [ 219.866217] ata1.01: error: { ICRC ABRT }
    [ 219.866271] ata1: soft resetting link
    [ 220.123155] ata1.00: configured for UDMA/44
    [ 220.138840] ata1.01: configured for UDMA/44
    [ 220.138889] ata1: EH complete
    [ 220.139718] sd 0:0:1:0: [sdb] 78165360 512-byte hardware sectors (40021 MB)
    [ 220.139860] sd 0:0:1:0: [sdb] Write Protect is off
    [ 220.139867] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
    [ 220.141282] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 220.142184] sd 0:0:0:0: [sda] 40031712 512-byte hardware sectors (20496 MB)
    [ 220.143021] sd 0:0:0:0: [sda] Write Protect is off
    [ 220.143032] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [ 220.143916] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 220.145200] sd 0:0:1:0: [sdb] 78165360 512-byte hardware sectors (40021 MB)
    [ 220.145344] sd 0:0:1:0: [sdb] Write Protect is off
    [ 220.145351] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
    [ 220.146726] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 408.704790] usb 1-2: new full speed USB device using uhci_hcd and address 2
    [ 408.859905] usb 1-2: configuration #1 chosen from 1 choice
    [ 409.011221] ndiswrapper version 1.52 loaded (smp=yes, preempt=no)
    [ 409.180477] usb 1-2: reset full speed USB device using uhci_hcd and address 2
    [ 409.392151] ndiswrapper: driver wnbusl51 (I-O DATA DEVICE,INC.,4/10/2003, 3.0.2) loaded
    [ 410.864913] wlan0: ethernet device 00:a0:b0:49:9f:27 using NDIS driver: wnbusl51, version: 0x30002, NDIS version: 0x501, vendor: 'I-O DATA WN-B11/USBSL Wireless LAN Adapter', 04BB:0924.F.conf
    [ 410.865011] BUG: unable to handle kernel paging request at virtual address e3e60728
    [ 410.865022] printing eip: e0e35c65 *pde = 00000000
    [ 410.865033] Oops: 0002 [#1] SMP
    [ 410.865039] Modules linked in: ndiswrapper nls_iso8859_1 nls_cp437 usb_storage libusual binfmt_misc rfcomm l2cap bluetooth ipv6 ppdev cpufreq_stats cpufreq_conservative cpufreq_ondemand cpufreq_userspace freq_table cpufreq_powersave container video output dock sbs sbshc battery vfat fat ac pppoatm ppp_generic slhc lp snd_ens1371 gameport snd_ac97_codec ac97_bus snd_pcm_oss snd_mixer_oss snd_pcm evdev snd_seq_dummy serio_raw psmouse bt878 snd_seq_oss nvidia(P) tuner tea5767 tda8290 tuner_simple mt20xx pcspkr snd_seq_midi snd_rawmidi tea5761 snd_seq_midi_event button bttv ir_common snd_seq snd_timer compat_ioctl32 i2c_algo_bit i2c_viapro snd_seq_device videobuf_dma_sg videobuf_core btcx_risc tveeprom i2c_core via686a snd videodev v4l2_common v4l1_compat parport_pc via_agp soundcore parport shpchp agpgart snd_page_alloc pci_hotplug iptable_nat nf_nat nf_conntrack_ipv4 nf_conntrack iptable_mangle iptable_filter ip_tables x_tables ext3 jbd mbcache sg sr_mod cdrom sd_mod 8139too floppy uhci_hcd 8139cp mii usbcore pata_via ata_generic pata_acpi libata scsi_mod thermal processor fan fbcon tileblit font bitblit softcursor fuse
    [ 410.865157]
    [ 410.865165] Pid: 6039, comm: modprobe Tainted: P (2.6.24-19-generic #1)
    [ 410.865172] EIP: 0060:[<e0e35c65>] EFLAGS: 00010297 CPU: 0
    [ 410.865278] EIP is at NdisDispatchPnp+0xb35/0xfc0 [ndiswrapper]
    [ 410.865284] EAX: 2d4e5720 EBX: de3c3c48 ECX: deee7800 EDX: 00000001
    [ 410.865289] ESI: deee7800 EDI: de3c3c44 EBP: de843480 ESP: de3c3b6c
    [ 410.865295] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
    [ 410.865302] Process modprobe (pid: 6039, ti=de3c2000 task=ded11140 task.ti=de3c2000)
    [ 410.865307] Stack: deee7800 00000100 de3c3b54 de3c3b50 00000010 00000049 0000009f 00000027
    [ 410.865319] e0e3c9bd dde91018 00030002 00000501 deee7800 deca919c 00000027 00000000
    [ 410.865330] de843000 c140a4b4 00000287 e0e3c9bd dde91018 00000501 deca919c 00030002
    [ 410.865341] Call Trace:
    [ 410.865393] [<c012813d>] finish_task_switch+0x8d/0x90
    [ 410.865428] [<c031aa7a>] schedule+0x20a/0x600
    [ 410.865455] [<c012103d>] kunmap_atomic+0x3d/0xb0
    [ 410.865469] [<c0172e8e>] get_page_from_freelist+0x29e/0x430
    [ 410.865492] [<e0e2e521>] IoAllocateIrp+0x61/0x80 [ndiswrapper]
    [ 410.865556] [<e0e2e815>] IofCallDriver+0x55/0xc0 [ndiswrapper]
    [ 410.865606] [<e0e3385b>] IoSendIrpTopDev+0xbb/0x120 [ndiswrapper]
    [ 410.865670] [<e0e33bb0>] pnp_start_device+0x50/0xb0 [ndiswrapper]
    [ 410.865736] [<e0e33e4f>] wrap_pnp_start_device+0x23f/0x290 [ndiswrapper]
    [ 410.865803] [<e0e34126>] wrap_pnp_start_usb_device+0xa6/0xd0 [ndiswrapper]
    [ 410.865837] [<c01a5251>] find_inode+0x31/0x60
    [ 410.865849] [<c01d70e0>] sysfs_ilookup_test+0x0/0x10
    [ 410.865882] [<c01d779b>] sysfs_addrm_finish+0x4b/0x1c0
    [ 410.865893] [<c01d7484>] sysfs_add_one+0x44/0xe0
    [ 410.865905] [<c01d758d>] sysfs_addrm_start+0x6d/0xb0
    [ 410.865915] [<c031b438>] mutex_lock+0x8/0x20
    [ 410.865926] [<e087782b>] usb_autopm_do_device+0x7b/0x100 [usbcore]
    [ 410.866024] [<e0877397>] usb_match_one_id+0x27/0xb0 [usbcore]
    [ 410.866071] [<e08785d9>] usb_probe_interface+0xb9/0x140 [usbcore]
    [ 410.866119] [<c02828a8>] driver_probe_device+0x88/0x190
    [ 410.866140] [<c0215f30>] kobject_uevent_env+0xf0/0x3d0
    [ 410.866170] [<c0282b1e>] driver_attach+0x9e/0xa0
    [ 410.866185] [<c0281cdb>] bus_for_each_dev+0x3b/0x60
    [ 410.866207] [<c0282726>] driver_attach+0x16/0x20
    [ 410.866215] [<c0282a80>]
    driver_attach+0x0/0xa0
    [ 410.866223] [<c028205a>] bus_add_driver+0x8a/0x1e0
    [ 410.866247] [<e087811e>] usb_register_driver+0x8e/0x110 [usbcore]
    [ 410.866295] [<e0e2340c>] loader_init+0x9c/0x140 [ndiswrapper]
    [ 410.866330] [<e0e3023f>] wrap_procfs_init+0x3f/0xb0 [ndiswrapper]
    [ 410.866364] [<e0e342f5>] wrapndis_init+0x45/0x50 [ndiswrapper]
    [ 410.866402] [<e0a6a0b7>] wrapper_init+0xb7/0xc2 [ndiswrapper]
    [ 410.866441] [<c01507c6>] sys_init_module+0x126/0x19c0
    [ 410.866545] [<c0168c90>] disable_irq+0x0/0x30
    [ 410.866587] [<c01043c2>] sysenter_past_esp+0x6b/0xa9
    [ 410.866632] =======================
    [ 410.866635] Code: ec ff ff 85 c0 0f 85 88 00 00 00 8b 54 24 60 c7 84 24 d8 00 00 00 00 00 00 00 8b 02 85 c0 74 34 31 d2 8b 4c 24 60 8b 44 91 04 90 <0f> ab 84 24 d8 00 00 00 83 c2 01 3b 11 72 e8 8b 84 24 d8 00 00
    [ 410.866684] EIP: [<e0e35c65>] NdisDispatchPnp+0xb35/0xfc0 [ndiswrapper] SS:ESP 0068:de3c3b6c
    [ 410.866726] ---[ end trace 2cd094c11aea708a ]---
    [ 428.738008] ADDRCONF(NETDEV_UP): wlan0: link is not ready
    [ 433.743750] eth0: link down
    [ 433.744326] ADDRCONF(NETDEV_UP): eth0: link is not ready
    [ 433.775574] ADDRCONF(NETDEV_UP): wlan0: link is not ready
    [ 434.156693] ndiswrapper (iw_set_freq:334): setting configuration failed (C0010015)
    [ 435.594690] NET: Registered protocol family 17
    [ 458.901068] ADDRCONF(NETDEV_UP): wlan0: link is not ready
    [ 459.277563] ndiswrapper (iw_set_freq:334): setting configuration failed (C0010015)
    [ 505.003009] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
    [ 515.848152] wlan0: no IPv6 routers present
    [ 565.066909] ndiswrapper (iw_set_freq:334): setting configuration failed (C0010015)
    [ 575.580157] wlan0: no IPv6 routers present
    [ 755.971059] ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
    [ 755.971074] ata1.01: BMDMA stat 0x64
    [ 755.971090] ata1.01: cmd ca/00:58:98:1e:3f/00:00:00:00:00/f3 tag 0 dma 45056 out
    [ 755.971094] res 51/84:00:98:1e:3f/00:00:00:00:00/f3 Emask 0x10 (ATA bus error)
    [ 755.971102] ata1.01: status: { DRDY ERR }
    [ 755.971107] ata1.01: error: { ICRC ABRT }
    [ 755.971170] ata1: soft resetting link
    [ 756.176068] ata1.00: configured for UDMA/44
    [ 756.191797] ata1.01: configured for UDMA/44
    [ 756.191842] ata1: EH complete

    [ 756.198792] sd 0:0:1:0: [sdb] Write Protect is off
    [ 756.198798] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
    [ 756.198835] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

     

    Related

    Wiki: ndiswrapper
    Patches: #1