From: andrew1056 <and...@gm...> - 2009-11-05 04:33:22
|
I originally bought the usb uirt for linuxmce, but switched over to mythtv. It was working at receiving and transmitting until the karmic upgrade. As a receiver I was using the devinput kernel module which is no longer found; however, there is no entry in /dev/input/event* for it. When lirc starts it no longer creates lirc0 which is what I was using for the receiver device previously. The problem is I can get it to both receive and transmit, but never at the same time. It's either one or the other. I can transmit when both are enabled, but not receive. If I try to run irw the errors in dmesg are this (I can still transmit fine though): [44130.798066] lircd[30700]: segfault at 8 ip 0806abf0 sp bfe85920 error 4 in lircd[8048000+29000] [44820.855226] lircd[5066]: segfault at 8 ip 0806abf0 sp bf93d6a0 error 4 in lircd[8048000+29000] [44997.870384] lircd[7519]: segfault at 8 ip 0806abf0 sp bfd46030 error 4 in lircd[8048000+29000] [45417.930491] lircd[11190]: segfault at 8 ip 0806abf0 sp bfa7bd90 error 4 in lircd[8048000+29000] [46029.160256] lircd[17511]: segfault at 8 ip 0806abf0 sp bfa56c90 error 4 in lircd[8048000+29000] [49775.489563] lircd[20802]: segfault at 8 ip 0806abf0 sp bf907650 error 4 in lircd[8048000+29000] [49808.492689] lircd[21191]: segfault at 8 ip 0806abf0 sp bfa33880 error 4 in lircd[8048000+29000] [49830.662147] lircd[21449]: segfault at 8 ip 0806abf0 sp bff4b550 error 4 in lircd[8048000+29000] [50001.806610] lircd[23222]: segfault at 8 ip 0806abf0 sp bfc42af0 error 4 in lircd[8048000+29000] [50012.333996] lircd[23440]: segfault at 8 ip 0806abf0 sp bf94b750 error 4 in lircd[8048000+29000] [50034.738573] lircd[23725]: segfault at 8 ip 0806abf0 sp bfb12a10 error 4 in lircd[8048000+29000] [50055.326874] lircd[23992]: segfault at 8 ip 0806abf0 sp bf9a1340 error 4 in lircd[8048000+29000] [52152.748237] lircd[15965]: segfault at 8 ip 0806abf0 sp bfa40d00 error 4 in lircd[8048000+29000] [52267.648977] lircd[17024]: segfault at 8 ip 0806abf0 sp bfc055a0 error 4 in lircd[8048000+29000] [52497.259426] lircd[17893]: segfault at 8 ip 0806abf0 sp bfdc5230 error 4 in lircd[8048000+29000] [59209.317623] lircd[28973]: segfault at 8 ip 0806abf0 sp bff5a150 error 4 in lircd[8048000+29000] [59285.695138] lircd[29908]: segfault at 8 ip 0806abf0 sp bfbbb3f0 error 4 in lircd[8048000+29000] [60163.103339] lircd[16750]: segfault at 8 ip 0806abf0 sp bf908460 error 4 in lircd[8048000+29000] [60479.037465] lircd[21188]: segfault at 8 ip 0806abf0 sp bfb96730 error 4 in lircd[8048000+29000] [60528.826164] lircd[21854]: segfault at 8 ip 0806abf0 sp bfaca6a0 error 4 in lircd[8048000+29000] [60597.677935] lircd[22630]: segfault at 8 ip 0806abf0 sp bffeae50 error 4 in lircd[8048000+29000] [60604.574566] lircd[22752]: segfault at 8 ip 0806abf0 sp bfa5ca90 error 4 in lircd[8048000+29000] [60624.762612] lircd[23044]: segfault at 8 ip 0806abf0 sp bfab37e0 error 4 in lircd[8048000+29000] The WAF has gone way down and I don't know if it's my config because somethings changed or something in lirc is broken. Here's hardware.conf # /etc/lirc/hardware.conf # #Chosen Remote Control REMOTE="Hauppauge_350" REMOTE_MODULES="" REMOTE_DRIVER="uirt2_raw" REMOTE_DEVICE="/dev/ttyUSB0" // used to be /dev/lirc0 but it's not created anymore REMOTE_LIRCD_CONF="hauppauge/lircd.conf.hauppauge" REMOTE_LIRCD_ARGS="" #Chosen IR Transmitter TRANSMITTER="SAE8000" TRANSMITTER_MODULES="" TRANSMITTER_DRIVER="uirt2_raw" TRANSMITTER_DEVICE="/dev/lircd1" TRANSMITTER_LIRCD_CONF="scientificatlanta/general.conf" TRANSMITTER_LIRCD_ARGS="" #Enable lircd START_LIRCD="true" #Don't start lircmd even if there seems to be a good config file #START_LIRCMD="false" #Try to load appropriate kernel modules LOAD_MODULES="true" # Default configuration files for your hardware if any LIRCMD_CONF="" #Forcing noninteractive reconfiguration #If lirc is to be reconfigured by an external application #that doesn't have a debconf frontend available, the noninteractive #frontend can be invoked and set to parse REMOTE and TRANSMITTER #It will then populate all other variables without any user input #If you would like to configure lirc via standard methods, be sure #to leave this set to "false" FORCE_NONINTERACTIVE_RECONFIGURATION="false" START_LIRCMD="" REMOTE_SOCKET="" TRANSMITTER_SOCKET="" lircd.conf just includes the hauppauge remote and the scientific atlanta box. -- View this message in context: http://old.nabble.com/USB-UIRT-Broken-in-karmic-tp26208569p26208569.html Sent from the LIRC mailing list archive at Nabble.com. |