From: Arnar B. <ar...@gm...> - 2007-03-01 21:05:33
|
Hi all, I built the latest buildroot, added python, uisp and some minor additions over the defaults. I copied it to the gumstix with hyperterminal. I ran a crc32 check after uploading and it matched. Immediately on booting I noticed errors from modprobe.conf, saying it was ignoring invalid lines (two of them) starting with "-e". The lines in question are here: options hostap_cs ignore_cis_vcc=1 options orinoco_cs ignore_cis_vcc=1 -e install pcmcia /sbin/modprobe --ignore-install pcmcia && modprobe pxa2xx-cs -e alias mwlan0 cfio install cfio /sbin/modprobe --ignore-install cfio && /sbin/modprobe mcf25 I then opened /etc/network/interfaces to configure the wifistix, but that files also has some lines starting with "-e": iface wlan0 inet dhcp -e auto mwlan0 iface mwlan0 inet dhcp pre-up /sbin/iwconfig $IFACE essid any txpower 100mW I checked the build_arm_nofpu/root/etc/... version of these files on the host, and they have those extra lines there too - so this was not caused by transfer errors. Any idea what can cause this? I'm using rev. 1313 of the buildroot. I haven't checked if other files are containing these errors as well. Arnar |
From: Chris D. <chr...@gm...> - 2007-03-01 21:37:14
|
Check out the 'possible problems' section at the bottom of this page in the wiki http://docwiki.gumstix.org/Buildroot_on_Ubuntu Chris On 3/1/07, Arnar Birgisson <ar...@gm...> wrote: > Hi all, > > I built the latest buildroot, added python, uisp and some minor > additions over the defaults. > > I copied it to the gumstix with hyperterminal. I ran a crc32 check > after uploading and it matched. > > Immediately on booting I noticed errors from modprobe.conf, saying it > was ignoring invalid lines (two of them) starting with "-e". The lines > in question are here: > > options hostap_cs ignore_cis_vcc=1 > options orinoco_cs ignore_cis_vcc=1 > -e > install pcmcia /sbin/modprobe --ignore-install pcmcia && modprobe pxa2xx-cs > > -e alias mwlan0 cfio > install cfio /sbin/modprobe --ignore-install cfio && /sbin/modprobe mcf25 > > > I then opened /etc/network/interfaces to configure the wifistix, but > that files also has some lines starting with "-e": > > iface wlan0 inet dhcp > -e > auto mwlan0 > iface mwlan0 inet dhcp > pre-up /sbin/iwconfig $IFACE essid any txpower 100mW > > > I checked the build_arm_nofpu/root/etc/... version of these files on > the host, and they have those extra lines there too - so this was not > caused by transfer errors. > > Any idea what can cause this? I'm using rev. 1313 of the buildroot. I > haven't checked if other files are containing these errors as well. > > Arnar > > ------------------------------------------------------------------------- > Take Surveys. Earn Cash. Influence the Future of IT > Join SourceForge.net's Techsay panel and you'll get the chance to share your > opinions on IT & business topics through brief surveys-and earn cash > http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV > _______________________________________________ > gumstix-users mailing list > gum...@li... > https://lists.sourceforge.net/lists/listinfo/gumstix-users > |
From: Arnar B. <ar...@gm...> - 2007-03-01 23:31:55
|
Oh.. erhm *blush* - Sorry I missed that. thanks, Arnar On 3/1/07, Chris Dollar <chr...@gm...> wrote: > Check out the 'possible problems' section at the bottom of this page > in the wiki http://docwiki.gumstix.org/Buildroot_on_Ubuntu > > Chris > > On 3/1/07, Arnar Birgisson <ar...@gm...> wrote: > > Hi all, > > > > I built the latest buildroot, added python, uisp and some minor > > additions over the defaults. > > > > I copied it to the gumstix with hyperterminal. I ran a crc32 check > > after uploading and it matched. > > > > Immediately on booting I noticed errors from modprobe.conf, saying it > > was ignoring invalid lines (two of them) starting with "-e". The lines > > in question are here: > > > > options hostap_cs ignore_cis_vcc=1 > > options orinoco_cs ignore_cis_vcc=1 > > -e > > install pcmcia /sbin/modprobe --ignore-install pcmcia && modprobe pxa2xx-cs > > > > -e alias mwlan0 cfio > > install cfio /sbin/modprobe --ignore-install cfio && /sbin/modprobe mcf25 > > > > > > I then opened /etc/network/interfaces to configure the wifistix, but > > that files also has some lines starting with "-e": > > > > iface wlan0 inet dhcp > > -e > > auto mwlan0 > > iface mwlan0 inet dhcp > > pre-up /sbin/iwconfig $IFACE essid any txpower 100mW > > > > > > I checked the build_arm_nofpu/root/etc/... version of these files on > > the host, and they have those extra lines there too - so this was not > > caused by transfer errors. > > > > Any idea what can cause this? I'm using rev. 1313 of the buildroot. I > > haven't checked if other files are containing these errors as well. > > > > Arnar > > > > ------------------------------------------------------------------------- > > Take Surveys. Earn Cash. Influence the Future of IT > > Join SourceForge.net's Techsay panel and you'll get the chance to share your > > opinions on IT & business topics through brief surveys-and earn cash > > http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV > > _______________________________________________ > > gumstix-users mailing list > > gum...@li... > > https://lists.sourceforge.net/lists/listinfo/gumstix-users > > > > ------------------------------------------------------------------------- > Take Surveys. Earn Cash. Influence the Future of IT > Join SourceForge.net's Techsay panel and you'll get the chance to share your > opinions on IT & business topics through brief surveys-and earn cash > http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV > _______________________________________________ > gumstix-users mailing list > gum...@li... > https://lists.sourceforge.net/lists/listinfo/gumstix-users > |