I used your default desktop image, it found the USB

## Booting kernel from Legacy Image at 82000000 ...

Image Name: Angstrom/

2.6.32/overo

Image Type: ARM Linux Kernel Image (uncompressed)

Data Size: 3154940 Bytes = 3 MB

Load Address: 80008000

Entry Point: 80008000

Verifying Checksum ...

OK

Loading Kernel Image ...

OK

OK

Starting kernel ...

Uncompressing Linux.........

............................................................

............................................................

............................................................

.................... done, booting the kernel.

Linux version 2.6.32 (steve@www.sakoman.com) (gcc version 4.3.3 (GCC) ) #1 We

d Jan 13 07:09:33 PST 2010

CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c53c7f

CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache

Machine: Gumstix Overo

Memory policy: ECC disabled, Data cache writeback

OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp )

SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000

Reserving 12582912 bytes SDRAM for VRAM

Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024

Kernel command line: console=ttyS2,115200n8 vram=12M omapfb.mode=dvi:1024x768MR-16@60 omapfb.debug=y omapdss.def_disp=dvi root=/dev/mtdblock4 rw rootfstype=jffs2

PID hash table entries: 1024 (order: 0, 4096 bytes)

Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)

Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)

Memory: 128MB 128MB = 256MB total

Memory: 240512KB available (5220K code, 596K data, 932K init, 0K highmem)

Hierarchical RCU implementation.

NR_IRQS:402

Clocking rate (Crystal/Core/MPU): 26.0/331/500 MHz

Reprogramming SDRC clock to 331882352 Hz

GPMC revision 5.0

IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts

Total of 96 interrupts on 1 active controller

OMAP GPIO hardware version 2.5

OMAP clockevent source: GPTIMER1 at 32768 Hz

Console: colour dummy device 80x30

Calibrating delay loop... 499.92 BogoMIPS (lpj=1949696)

Mount-cache hash table entries: 512

CPU: Testing write buffer coherency: ok

regulator: core version 0.5

NET: Registered protocol family 16

Found NAND on CS0

Registering NAND on CS0

OMAP DMA hardware revision 4.0

bio: create slab <bio-0> at 0

SCSI subsystem initialized

usbcore: registered new interface driver usbfs

usbcore: registered new interface driver hub

usbcore: registered new device driver usb

i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz

twl4030: PIH (irq 7) chaining IRQs 368..375

twl4030: power (irq 373) chaining IRQs 376..383

twl4030: gpio (irq 368) chaining IRQs 384..401

regulator: VUSB1V5: 1500 mV normal standby

regulator: VUSB1V8: 1800 mV normal standby

regulator: VUSB3V1: 3100 mV normal standby

twl4030_usb twl4030_usb: Initialized TWL4030 USB module

regulator: VMMC1: 1850 <--> 3150 mV normal standby

regulator: VDAC: 1800 mV normal standby

regulator: VPLL2: 1800 mV normal standby

i2c_omap i2c_omap.3: bus 3 rev3.12 at 400 kHz

Bluetooth: Core ver 2.15

NET: Registered protocol family 31

Bluetooth: HCI device and connection manager initialized

Bluetooth: HCI socket layer initialized

cfg80211: Using static regulatory domain info

cfg80211: Regulatory domain: US

\0x09(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)

\0x09(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)

\0x09(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)

\0x09(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)

\0x09(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)

\0x09(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)

\0x09(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)

cfg80211: Calling CRDA for country: US

Switching to clocksource 32k_counter

musb_hdrc: version 6.0, musb-dma, host, debug=0

musb_hdrc: USB Host mode controller at fa0ab000 using DMA, IRQ 92

musb_hdrc musb_hdrc: MUSB HDRC host driver

musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1

usb usb1: New USB device found, idVendor=1d6b, idProduct=0002

usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1

usb usb1: Product: MUSB HDRC host driver

usb usb1: Manufacturer: Linux 2.6.32 musb-hcd

usb usb1: SerialNumber: musb_hdrc

usb usb1: configuration #1 chosen from 1 choice

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 1 port detected

NET: Registered protocol family 2

IP route cache hash table entries: 2048 (order: 1, 8192 bytes)

TCP established hash table entries: 8192 (order: 4, 65536 bytes)

TCP bind hash table entries: 8192 (order: 3, 32768 bytes)

TCP: Hash tables configured (established 8192 bind 8192)

TCP reno registered

NET: Registered protocol family 1

RPC: Registered udp transport module.

RPC: Registered tcp transport module.

RPC: Registered tcp NFSv4.1 backchannel transport module.

VFS: Disk quotas dquot_6.5.2

Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)

JFFS2 version 2.2. (NAND) (SUMMARY) \0xc2\0xa9 2001-2006 Red Hat, Inc.

msgmni has been set to 470

alg: No test for stdrng (krng)

io scheduler noop registered

io scheduler anticipatory registered

io scheduler deadline registered

io scheduler cfq registered (default)

OMAP DSS rev 2.0

OMAP DISPC rev 3.0

OMAP VENC rev 2

Serial: 8250/16550 driver, 4 ports, IRQ sh

aring enabled

serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654

serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654

serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654

console [ttyS2] enabled

brd: module loaded

loop: module loaded

omap2-nand driver initializing

NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 256MiB 1,8V 16-bit)

cmdlinepart partition parsing not available

Creating 5 MTD partitions on "omap2-nand":

0x000000000000-0x000000080000 : "xloader"

0x000000080000-0x000000240000 : "uboot"

0x000000240000-0x000000280000 : "uboot environment"

0x000000280000-0x000000680000 : "linux"

0x000000680000-0x000010000000 : "rootfs"

smsc911x: Driver version 2008-10-21.

smsc911x-mdio: probed

eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:01, irq=-1)

net eth0: MAC Address: 00:15:c9:28:d3:ce

smsc911x: Driver version 2008-10-21.

usbcore: registered new interface driver asix

usbcore: registered new interface driver cdc_ether

ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

ehci-omap ehci-omap.0: OMAP-EHCI Host Controller

ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 2

ehci-omap ehci-omap.0: irq 77, io mem 0x48064800

usb 1-1: new high speed USB device using musb_hdrc and address 2

ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00

usb usb2: New USB device found, idVendor=1d6b, idProduct=0002

usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1

usb usb2: Product: OMAP-EHCI Host Controller

usb usb2: Manufacturer: Linux 2.6.32 ehci_hcd

usb usb2: SerialNumber: ehci-omap.0

usb usb2: configuration #1 chosen from 1 choice

hub 2-0:1.0: USB hub found

hub 2-0:1.0: 3 ports detected

Initializing USB Mass Storage driver...

usbcore: registered new interface driver usb-storage

USB Mass Storage support registered.

udc: OMAP UDC driver, version: 4 October 2004 (iso) (dma)

mice: PS/2 mouse device common for all mice

twl4030_rtc twl4030_rtc: rtc core: registered twl4030_rtc as rtc0

twl4030_rtc twl4030_rtc: Power up reset detected.

twl4030_rtc twl4030_rtc: Enabling TWL4030-RTC.

i2c /dev entries driver

OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec

Bluetooth: HCI UART driver ver 2.2

Bluetooth: HCI H4 protocol initialized

Bluetooth: HCI BCSP protocol initialized

Bluetooth: HCILL protocol initialized

usb 1-1: New USB device found,

idVendor=04b4, idProduct=6560

usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0

usb 1-1: configuration #1 chosen from 1 choice

hub 1-1:1.0: USB hub found

hub 1-1:1.0: 4 ports detected

usbcore: registered new interface driver usbhid

usbhid: v2.6:USB HID core driver

Advanced Linux Sound Architecture Driver Version 1.0.21.

usbcore: registered new interface driver snd-usb-audio

No device for DAI twl4030

No device for DAI twl4030 Voice

No device for DAI omap-mcbsp-dai-0

No device for DAI omap-mcbsp-dai-1

No device for DAI omap-mcbsp-dai-2

No device for DAI omap-mcbsp-dai-3

No device for DAI omap-mcbsp-dai-4

overo SoC init

TWL4030 Audio Codec init

asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok

ALSA device list:

#0: overo (twl4030)

oprofile: using arm/armv7

TCP cubic registered

NET: Registered protocol family 17

NET: Registered protocol family 15

Bluetooth: L2CAP ver 2.14

Bluetooth: L2CAP socket layer initialized

Bluetooth: SCO (Voice Link) ver 0.6

Bluetooth: SCO socket layer initialized

Bluetooth: RFCOMM TTY layer initialized

Bluetooth: RFCOMM socket layer initialized

Bluetooth: RFCOMM ver 1.11

Bluetooth: BNEP (Ethernet Emulation) ver 1.3

Bluetooth: BNEP filters: protocol multicast

Bluetooth: HIDP (Human Interface Emulation) ver 1.2

ThumbEE CPU extension supported.

Power Management for TI OMAP3.

VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1

fbcvt: 1024x768@60: CVT Name - .786M3-R

Console: switching to colour frame buffer device 128x48

usb 1-1.3: new full speed USB device using musb_hdrc and address 3

regulator_init_complete: incomplete constraints, leaving VDVI on

regulator_init_complete: incomplete constraints, leaving VDAC on

twl4030_rtc twl4030_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)

usb 1-1.3: New USB device found, idVendor=1a86, idProduct=7523

usb 1-1.3: New USB device str

ings: Mfr=0, Product=2, SerialNumber=0

usb 1-1.3: Product: USB2.0-Ser!

usb 1-1.3: configuration #1 chosen from 1 choice

mmc1: new SDIO card at address 0001

JFFS2 notice: (1) jffs2_build_xattr_subsystem: complete building xatt

r subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.

VFS: Mounted root (jffs2 filesystem) on device 31:4.

Freeing init memory: 932K

INIT: version 2.86 booting

Please wait: booting...

Starting udev

udev: renamed network interface eth0 to eth1

ads7846 spi1.0: touchscreen, irq 274

usbcore: registered new interface driver usbserial

USB Serial support registered for generic

usbcore: registered new interface driver usbserial_generic

usbserial: USB Serial Driver core

input: ADS7846 Touchscreen as /devices/platform/omap2_mcspi.1/spi1.0/input/input0

USB Serial support registered for ch341-uart

ch341 1-1.3:1.0: ch341-uart converter detected

usb 1-1.3: ch341-uart converter now attached to ttyUSB0

usbcore: registered new interface driver ch341

lib80211: common routines for IEEE802.11 drivers

libertas_sdio: Libertas SDIO driver

libertas_sdio: Copyright Pierre Ossman

libertas_sdio mmc1:0001:1: firmware: requesting sd8686_helper.bin

libertas_sdio mmc1:0001:1: firmware: requesting sd8686.bin

libertas: 00:19:88:3d:20:73, fw 9.70.3p24, cap 0x00000303

libertas: wlan0: Marv

ell WLAN 802.11 adapter

Populating dev cache

Remounting root file system...

NET: Registered protocol family 10

ALSA: Restoring mixer settings...

Configuring network interfaces...

done.

Starting portmap daemon: portmap.

net.ipv4.conf.default.rp_filter = 1

net.ipv4.conf.all.rp

_filter = 1

Tue Jan 5 13:57:00 GMT 2010

Turning echo off on /dev/ttyS1

INIT: Entering runlevel: 5

Starting system message bus:

dbus.

Starting Hardware abstraction layer hald

Starting OpenBSD Secure Shell server: sshd

done.

Starting advanced power management daemon: No APM support in kernel

(failed.)

Starting ntpd: done

Starting syslogd/klogd: done

* Starting A

vahi mDNS/DNS-SD Daemon: avahi-daemon

[ ok ]

Starting Bluetooth subsystem:

CSR build ID 0x0C-0x5C

Device setup complete

ttyS1 bluetoothd hid2hci

rfcomm.

Waiting for connection on channel 1

Starting Network connection manager daemo

n: NetworkManager

.

Starting PVR

PVRSRV_PIXEL_FORMAT_RGB565

Starting GPE display manager: gpe-dm

.-------.

| |

.-.

| | |-----.-----.-----.| | .----..-----.-----.

| | | __ | ---'| '--.| .-'| | |

| | | | | |--- || net eth1: SMSC911x/921x identified at 0xd08c8000, IRQ: 336

--'| | | ' | | | |

'---'---'--'--'--. |-----''----''--' '-----'-'-'-'

-' |

'---'

The Angstrom Distribution overo ttyS2

Angstrom 2009.X-test-20100101 overo ttyS2

overoADDRCONF(NETDEV_UP): wlan0: link is not ready

login:

ls dev

audio\0x09\0x09 mem\0x09\0x09 ram11 tty15 tty4 tty7

block\0x09\0x09 mi

xer\0x09\0x09 ram12 tty16 tty40 tty8

bus\0x09\0x09 mtd0\0x09\0x09 ram13 tty17 tty41 tty9

char\0x09\0x09 mtd0ro\0x09\0x09 ram14 tty18 tty42 ttyS0

console\0x09\0x09 mtd1\0x09\0x09 ram15 tty19 tty43 ttyS1

cpu_dma_latency mtd1ro\0x09\0x09 ram2 tty2 tty44 ttyS2

dsp\0x09\0x09 mtd2\0x09\0x09 ram3 tty20 tty45 ttyS3

fb\0x09\0x09 mtd2ro\0x09\0x09 ram4 tty21 tty46 ttyUSB0

fb0\0x09\0x09 mtd3\0x09\0x09 ram5 tty22 tty47 twl4030-madc

fb1\0x09\0x09 mtd3ro\0x09\0x09 ram6 tty23 tty48 ubi_ctrl

fb2\0x09\0x09 mtd4\0x09\0x09 ram7 tty24 tty49 udev_network_queue

full\0x09\0x09 mtd4ro\0x09\0x09 ram8 tty25 tty5 urandom

i2c-1\0x09\0x09 mtdblock0\0x09 ram9 tty26 tty50 usbmon0

i2c-3\0x09\0x09 mtdblock1\0x09 random tty27 tty51 usbmon1

initctl\0x09\0x09 mtdblock2\0x09 rtc tty28 tty52 usbmon2

input\0x09\0x09 mtdblock3\0x09 rtc0 tty29 tty53 vcs

kmem\0x09\0x09 mtdblock4\0x09 serial tty3 tty54 vcs1

kmsg\0x09\0x09 network_latency shm tty30 tty55 vcs2

log\0x09\0x09 network_throughput snd tty31 tty56 vcs3

loop0\0x09\0x09 null\0x09\0x09 tty tty32 tty57 vcsa

loop1\0x09\0x09 psaux\0x09\0x09 tty0 tty33 tty58 vcsa1

loop2\0x09\0x09 ptmx\0x09\0x09 tty1 tty34 tty59 vcsa2

loop3\0x09\0x09 pts\0x09\0x09 tty10 tty35 tty6 vcsa3

loop4\0x09\0x09 pvrsrvkm\0x09 tty11 tty36 tty60 watchdog

loop5\0x09\0x09 ram0\0x09\0x09 tty12 tty37 tty61 zero

loop6\0x09\0x09 ram1\0x09\0x09 tty13 tty38 tty62

loop7\0x09\0x09 ram10\0x09\0x09 tty14 tty39 tty63

root@overo:/#



On 28 October 2010 15:08, Liem Leong <liem.leong@googlemail.com> wrote:
Hi Steve,

If we can't find it in dev, is these usb we are looking for and Gumstix is rejecting its/

I2C read: I/O error

I2C read: I/O error

mmc1 is available

reading boot.scr

Invalid FAT entry

** Unable to read "boot.scr" from mmc 0:1 **

reading uImage

3160116 bytes read

Booting from mmc ...

## Booting kernel from Legacy Image at 82000000 ...

Image Name: Angstrom/2.6.34/overo

Image Type: ARM Linux Kernel Image (uncompressed)

Data Size: 3160052 Bytes = 3 MiB

Load Address: 80008000

Entry Point: 80008000

Verifying Checksum ...

OK

Loading Kernel Image ...

OK

OK

Starting kernel ...

Uncompressing Linux...

done, booting the kernel.

Linux version 2.6.34 (liem@liem-laptop) (gcc version 4.3.3 (GCC)

) #1 Fri Oct 22 06:27:53 BST 2010

CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c53c7f

CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache

Machine: Gumstix Overo

Memory policy: ECC disabled, Data cache writeback

OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp )

SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000

Reserving 12582912 bytes SDRAM for VRAM

Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024

Kernel command line: console=ttyS2,115200n8 vram=12M omapfb.mode=dvi:1024x768MR-16@60 omapfb.debug=y omapdss.def_disp=dvi root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait

PID hash table entries: 1024 (order: 0, 4096 bytes)

Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)

Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)

Memory: 128MB 128MB = 256MB total

Memory: 240920k/240920k available, 21224k reserved, 0K highmem

Virtual kernel memory layout:

vector : 0xffff0000 - 0xffff1000 ( 4 kB)

fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)

DMA : 0xffc00000 - 0xffe00000 ( 2 MB)

vmalloc : 0xd0800000 - 0xf8000000 ( 632 MB)

lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)

modules : 0xbf000000 - 0xc0000000 ( 16 MB)

.init : 0xc0008000 - 0xc00f2000 ( 936 kB)

.text : 0xc00f2000 - 0xc05f6000 (5136 kB)

.data : 0xc061a000 - 0xc0659400 ( 253 kB)

Hierarchical RCU implementation.

NR_IRQS:402

Clocking rate (Crystal/Core/MPU): 26.0/224/500 MHz

Reprogramming SDRC clock to 224791666 Hz

dpll3_m2_clk rate change failed: -22

GPMC revision 5.0

IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts

Total of 96 interrupts on 1 active controller

OMAP GPIO hardware version 2.5

OMAP clockevent source: GPTIMER1 at 32768 Hz

Console: colour dummy device 80x30

Calibrating delay loop... 499.92 BogoMIPS (lpj=1949696)

Mount-cache hash table entries: 512

CPU: Testing write buffer coherency: ok

devtmpfs: initialized

regulator: core version 0.5

NET: Registered protocol family 16

Found NAND on CS0

hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available

OMAP DMA hardware revision 4.0

bio: create slab <bio-0> at 0

SCSI subsystem initialized

usbcore: registered new interface driver usbfs

usbcore: registered new interface driver hub

usbcore: registered new device driver usb

i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz

twl4030: PIH (irq 7) chaining IRQs 368..375

twl4030: power (irq 373) chaining IRQs 376..383

twl4030: gpio (irq 368) chaining IRQs 384..401

regulator: VUSB1V5: 1500 mV normal standby

regulator: VUSB1V8: 1800 mV normal standby

regulator: VUSB3V1: 3100 mV normal standby

twl4030_usb twl4030_usb: Initialized TWL4030 USB module

regulator: VMMC1: 1850 <--> 3150 mV at 3000 mV normal standby

regulator: VDAC: 1800 mV normal standby

regulator: VDVI: 1800 mV normal standby

i2c_omap i2c_omap.3: bus 3 rev3.12 at 400 kHz

Advanced Linux Sound Architecture Driver Version 1.0.22.1.

Bluetooth: Core ver 2.15

NET: Registered protocol family 31

Bluetooth: HCI device and connection manager initialized

Bluetooth: HCI socket layer initialized

cfg80211: Calling CRDA to update world regulatory domain

Switching to clocksource 32k_counter

musb_hdrc: version 6.0, musb-dma, host, debug=0

musb_hdrc musb_hdrc: MUSB HDRC host driver

musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1

usb usb1: New USB device found, idVendor=1d6b, idProduct=0002

usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1

usb usb1: Product: MUSB HDRC host driver

usb usb1: Manufacturer: Linux 2.6.34 musb-hcd

usb usb1: SerialNumber: musb_hdrc

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 1 port detected

musb_hdrc musb_hdrc: USB Host mode controller at fa0ab000 using DMA, IRQ 92

NET: Registered protocol family 2

IP route cache hash table entries: 2048 (order: 1, 8192 bytes)

TCP established hash table entries: 8192 (order: 4, 65536 bytes)

TCP bind hash table entries: 8192 (order: 3, 32768 bytes)

TCP: Hash tables configured (established 8192 bind 8192)

TCP reno registered

UDP hash table entries: 256 (order: 0, 4096 bytes)

UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)

NET: Registered protocol family 1

RPC: Registered udp transport module.

RPC: Registered tcp transport module.

RPC: Registered tcp NFSv4.1 backchannel transport module.

VFS: Disk quotas dquot_6.5.2

Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)

JFFS2 version 2.2. (NAND) (SUMMARY) \0xc2\0xa9 2001-2006 Red Hat, Inc.

msgmni has been set to 470

alg: No test for stdrng (krng)

Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)

io scheduler noop registered

io scheduler deadline registered

io scheduler cfq registered (default)

OMAP DSS rev 2.0

OMAP DISPC rev 3.0

OMAP VENC rev 2

OMAP DSI rev 1.0

Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled

serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654

serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654

serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654

console [ttyS2] enabled

brd: module loaded

loop: module loaded

omap2-nand driver initializing

NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 256MiB 1,8V 16-bit)

cmdlinepart partition parsing not available

Creating 5 MTD partitions on "omap2-nand.0":

0x000000000000-0x000000080000 : "xloader"

0x000000080000-0x000000240000 : "uboot"

0x000000240000-0x000000280000 : "uboot environment"

0x000000280000-0x000000680000 : "linux"

0x000000680000-0x000010000000 : "rootfs"

smsc911x: Driver version 2008-10-21.

smsc911x-mdio: probed

eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:01, irq=-1)

net eth0: MAC Address: 00:15:c9:28:d3:ce

smsc911x: Driver version 2008-10-21.

usbcore: registered new interface driver asix

usbcore: registered new interface driver cdc_ether

ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

ehci-omap ehci-omap.0: OMAP-EHCI Host Controller

ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 2

ehci-omap ehci-omap.0: irq 77, io mem 0x48064800

usb 1-1: new high speed USB device using musb_hdrc and address 2

ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00

usb usb2: New USB device found, idVendor=1d6b, idProduct=0002

usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1

usb usb2: Product: OMAP-EHCI Host Controller

usb usb2: Manufacturer: Linux 2.6.34 ehci_hcd

usb usb2: SerialNumber: ehci-omap.0

hub 2-0:1.0: USB hub found

hub 2-0:1.0: 3 ports detected

Initializing USB Mass Storage driver...

usbcore: registered new interface driver usb-storage

USB Mass Storage support registered.

udc: OMAP UDC driver, version: 4 October 2004 (iso) (dma)

mice: PS/2 mouse device common for all mice

twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0

twl_rtc twl_rtc: Power up reset detected.

i2c /dev entries driver

OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec

twl4030_wdt twl4030_wdt: Failed to register misc device

twl4030_wdt: probe of twl4030_wdt failed with error -16

Bluetooth: HCI UART driver ver 2.2

Bluetooth: HCI H4 protocol initialized

Bluetooth: HCI BCSP protocol initialized

Bluetooth: HCILL protocol initialized

usbcore: registered new interface driver usbhid

usbhid: USB HID core driver

usbcore: registered new interface driver snd-usb-audio

No device for DAI omap-mcbsp-dai-0

No device for DAI omap-mcbsp-dai-1

No dev

ice for DAI omap-mcbsp-dai-2

No device for DAI omap-mcbsp-dai-3

No device for DAI omap-mcbsp-dai-4

overo SoC init

asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok

ALSA device list:

#0: overo (twl4030)

oprofile: using arm/armv7

TCP cubic registered

NET: Registered protocol family 17

NET: Registered protocol family 15

Bluetooth: L2CAP ver 2.14

Bluetooth: L2CAP socket layer initialized

Bluetooth: SCO (Voice Link) ver 0.6

Bluetooth: SCO socket layer initialized

Bluetooth: RFCOMM TTY layer initialized

Bluetooth: RFCOMM socket layer initialized

Bluetooth: RFCOMM ver 1.11

Bluetooth: BNEP (Ethernet Emulation) ver 1.3

Bluetooth: BNEP filters: protocol multicast

Bluetooth: HIDP (Human Interface Emulation) ver 1.2

ThumbEE CPU extension supported.

Power Management for TI OMAP3.

VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1

fbcvt: 1024x768@60: CVT Name - .786M3-R

usb 1-1: New USB device found, idVendor=04b4, idProduct=6560

usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0

hub 1-1:1.0: USB hub found

hub 1-1:1.0: 4 ports detected

Console: switching to colour frame buffer device 128x48

regulator_init_complete: incomplete constraints, leaving VDAC on

twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:17 UTC (946684817)

Waiting for root device /dev/mmcblk0p2...

usb 1-1.3: new full speed USB device using musb_hdrc and address 3

usb 1-1.3: New USB device found, idVendor=1a86, idProduct=7523

usb 1-1.3: New USB device

strings: Mfr=0, Product=2, SerialNumber=0

usb 1-1.3: Product: USB2.0-Ser!

mmc0: host does not support reading read-only switch. assuming write-enable.

mmc0: new high speed SDHC card at address 1234

mmcblk0: mmc0:1234 SA04G 3.68 GiB

mmcblk0: p1 p2

mmc1: new SDIO card at address 0001

kjournald starting. Commit interval 5 seconds

EXT3-fs (mmcblk0p2): warning: maximal mount count reach

ed, running e2fsck is recommended

EXT3-fs (mmcblk0p2): using internal journal

EXT3-fs (mmcblk0p2): recovery com

plete

EXT3-fs (mmcblk0p2): mounted filesystem with writeback data mode

VFS: Mounted root (ext3 filesystem) on device 179:2.

devtmpfs: mounted

Freeing init memory: 936K

INIT: version 2.86 booting

Please wait: booting...

Starting udev

udev: starting version 151

udev: renamed network interface eth0 to eth1

Remounting root file system...

quiet_error: 47 callbacks suppressed

udevadm settle - timeout of 8 seconds reached, the event queue contai

ns:

/sys/devices/platform/mmci-omap-hs.0/mmc_host/mmc0/mmc0:1234/block/mmcblk0/mmcblk0p1 (586)

/sys/devices/platform/mmci-omap-hs.0/mmc_host/mmc0/mmc0:1234/block/mmcblk0/mmcblk0p2 (587)

Caching udev devnodes

Populating dev cache

Configuring network interfaces... ifconfig: SIOCGIFFLAGS: No such devi

ce

done.

Starting portmap daemon: portmap.

net.ipv4.conf.default.rp_filter = 1

net.ipv4.conf.all.rp_filter = 1

Sun Oct 24 12:01:00 UTC 2010

INIT: Entering runlevel: 5

Starting system message bus: dbus.

Starting Dropbear SSH server:

dropbear.

Starting syslogd/klogd: done

* Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon

...done.

Starting NTP Client.

.-------.

| |

.-.

| | |-----.-----.-----.| | .----..-----.-----.

| | | __ | ---'| '--.| .-'| | |

| | | | | |--- || --'| | | ' | | | |

'---'---'--'--'--. |-----''----''--' '-----'-'-'-'

-' |

'---'

The Angstrom Distribution hawkboard ttyS2

Angstrom 2010.7-test-20101023 hawkboard ttyS2

hawkboard login:



On 28 October 2010 15:01, Liem Leong <liem.leong@googlemail.com> wrote:
OK, it plugged with a powered USB hub now, no I haven't changed anything when it came from Gumstix.

It the same, do you want me to try the console port too?

../../dev

audio pts tty36

block ram0

tty37

bus ram1 tty38

char ram10 tty39

console ram11 tty4

cpu_dma_latency ram12 tty40

disk ram13 tty41

dsp ram14 tty42

fb ram15 tty43

fb0 ram2 tty44

fb1 ram3 tty45

fb2 ram4 tty46

full ram5 tty47

i2c-1 ram6 tty48

i2c-3 ram7 tty49

initctl ram8 tty5

input ram9 tty50

kmem random tty51

kmsg rtc tty52

log rtc0 tty53

loop0 shm tty54

loop1 snd tty55

loop2 tty tty56

loop3 tty0 tty57

loop4 tty1 tty58

loop5 tty10 tty59

loop6 tty11 tty6

loop7 tty12 tty60

mem tty13 tty61

mixer tty14 tty62

mmcblk0 tty15 tty63

mmcblk0p1 tty16 tty7

mmcblk0p2 tty17 tty8

mtd0 tty18 tty9

mtd0ro tty19 ttyS0

mtd1 tty2 ttyS1

mtd1ro tty20 ttyS2

mtd2 tty21 ttyS3

mtd2ro tty22 twl4030-madc

mtd3 tty23 ubi_ctrl

mtd3ro tty24 udev_network_queue

mtd4 tty25 urandom

mtd4ro tty26 usbmon0

mtdblock0 tty27 usbmon1

mtdblock1 tty28 usbmon2

mtdblock2 tty29 vcs

mtdblock3 tty3 vcs1

mtdblock4 tty30 vcsa

network_latency tty31 vcsa1

network_throughput tty32 watchdog

null tty33 zero

psaux tty34

ptmx tty35

root@hawkboard:~#



On 28 October 2010 14:49, dtran11 <dtran11@gmail.com> wrote:

You can try the OTG port. It defaults to Host mode unless you changed it.
--
View this message in context: http://old.nabble.com/Chestnut-expansion-board-tp30026306p30076806.html
Sent from the Gumstix mailing list archive at Nabble.com.


------------------------------------------------------------------------------
Nokia and AT&T present the 2010 Calling All Innovators-North America contest
Create new apps & games for the Nokia N8 for consumers in  U.S. and Canada
$10 million total in prizes - $4M cash, 500 devices, nearly $6M in marketing
Develop with Nokia Qt SDK, Web Runtime, or Java and Publish to Ovi Store
http://p.sf.net/sfu/nokia-dev2dev
_______________________________________________
gumstix-users mailing list
gumstix-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/gumstix-users



--

=======================
Liem Leong




--

=======================
Liem Leong




--

=======================
Liem Leong