Hi all,

I have the following problem, when i start the gumstix overo fire it can't
boot properly. Here are the messages i get from the console:


*****************************************************************************************
*****************************************************************************************
*****************************************************************************************
*****************************************************************************************


Texas Instruments X-Loader 1.4.2 (Mar 27 2009 - 08:51:34)
Loading u-boot.bin from nand
Skipped bad block at 0xa0000


U-Boot 2009.03 (Mar 27 2009 - 08:52:42)

OMAP3530-GP rev 2, CPU-OPP2 L3-165MHz
Gumstix Overo board + LPDDR/NAND
DRAM: 256 MB
NAND: 256 MiB
*** Warning - bad CRC or NAND, using default environment

In: serial
Out: serial
Err: serial
Die ID #67fc00040000000004032d460c021009
Hit any key to stop autoboot: 0
No MMC card found
Booting from nand ...

NAND read: device 0 offset 0x280000, size 0x400000
4194304 bytes read: OK
## Booting kernel from Legacy Image at 82000000 ...
Image Name: Angstrom/2.6.29-rcfinal+r0+git90
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2723228 Bytes = 2.6 MB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing
Linux...................................................................................................................................................................................
done, booting the kernel.
Linux version 2.6.29-omap1 (sakoman@otto) (gcc version 4.3.1 (GCC) ) #1 Fri
Mar 27 08:57:46 PDT 2009
CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c5387f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: Gumstix Overo
omapfb_early_vram, 12582912, 0x0
Memory policy: ECC disabled, Data cache writeback
OMAP3430 ES3.1
SRAM: Mapped pa 0x40200000 to va 0xd7000000 size: 0x100000
Reserving 12582912 bytes SDRAM for VRAM
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Kernel command line: console=ttyS2,115200n8 vram=12M
omapfb.mode=dvi:1024x768MR-16@60 omapfb.debug=y omapdss.def_disp=dvi
root=/dev/mtdblock4 rw rootfstype=jffs2
Clocking rate (Crystal/DPLL/ARM core): 26.0/331/500 MHz
GPMC revision 5.0
IRQ: Found an INTC at 0xd8200000 (revision 4.0) with 96 interrupts
Total of 96 interrupts on 1 active controller
OMAP34xx GPIO hardware version 2.5
PID hash table entries: 1024 (order: 10, 4096 bytes)
OMAP clockevent source: GPTIMER1 at 32768 Hz
Console: colour dummy device 80x30
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 128MB 128MB = 256MB total
Memory: 241408KB available (4460K code, 531K data, 940K init)
Calibrating delay loop... 499.92 BogoMIPS (lpj=1949696)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 764 bytes
regulator: core version 0.5
NET: Registered protocol family 16
Found NAND on CS0
Registering NAND on CS0
OMAP DMA hardware revision 4.0
bio: create slab <bio-0> at 0
OMAP DSS rev 2.0
OMAP DISPC rev 3.0
OMAP VENC rev 2
i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz
twl4030: PIH (irq 7) chaining IRQs 368..375
twl4030: power (irq 373) chaining IRQs 376..383
twl4030: gpio (irq 368) chaining IRQs 384..401
regulator: VMMC1: 1850 <--> 3150 mV normal standby
regulator: VUSB1V5: 1500 <--> 0 mV normal standby
regulator: VUSB1V8: 1800 <--> 0 mV normal standby
regulator: VUSB3V1: 3100 <--> 0 mV normal standby
i2c_omap i2c_omap.3: bus 3 rev3.12 at 400 kHz
SCSI subsystem initialized
twl4030_usb twl4030_usb: Initialized TWL4030 USB module
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Bluetooth: Core ver 2.14
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
musb_hdrc: version 6.0, musb-dma, host, debug=0
musb_hdrc: USB Host mode controller at d80ab000 using DMA, IRQ 92
musb_hdrc musb_hdrc: MUSB HDRC host driver
musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: MUSB HDRC host driver
usb usb1: Manufacturer: Linux 2.6.29-omap1 musb-hcd
usb usb1: SerialNumber: musb_hdrc
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
JFFS2 version 2.2. (NAND) (SUMMARY) 2001-2006 Red Hat, Inc.
msgmni has been set to 471
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
serial8250.0: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
serial8250.0: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654
console [ttyS2] enabled
brd: module loaded
loop: module loaded
usbcore: registered new interface driver asix
usbcore: registered new interface driver cdc_ether
i2c /dev entries driver
Driver 'sd' needs updating - please use bus_type methods
omap2-nand driver initializing
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 256MiB 1,8V
16-bit)
cmdlinepart partition parsing not available
Creating 5 MTD partitions on "omap2-nand":
0x000000000000-0x000000080000 : "xloader"
0x000000080000-0x000000240000 : "uboot"
0x000000240000-0x000000280000 : "uboot environment"
0x000000280000-0x000000680000 : "linux"
0x000000680000-0x000010000000 : "rootfs"
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 2
ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OMAP-EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.29-omap1 ehci_hcd
usb usb2: SerialNumber: ehci-omap.0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
udc: OMAP UDC driver, version: 4 October 2004 (iso) (dma)
mice: PS/2 mouse device common for all mice
twl4030_rtc twl4030_rtc: rtc core: registered twl4030_rtc as rtc0
twl4030_rtc twl4030_rtc: Power up reset detected.
twl4030_rtc twl4030_rtc: Enabling TWL4030-RTC.
OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
Bluetooth: HCI UART driver ver 2.2
Bluetooth: HCI H4 protocol initialized
Bluetooth: HCI BCSP protocol initialized
Bluetooth: Broadcom Blutonium firmware driver ver 1.2
usbcore: registered new interface driver bcm203x
Bluetooth: Digianswer Bluetooth USB driver ver 0.10
usbcore: registered new interface driver bpa10x
mmci-omap-hs mmci-omap-hs.0: Failed to get debounce clock
regulator: Unable to get requested regulator: vmmc_aux
mmci-omap-hs mmci-omap-hs.1: Failed to get debounce clock
regulator: Unable to get requested regulator: vmmc
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.18a.
usbcore: registered new interface driver snd-usb-audio
No device for DAI twl4030
No device for DAI omap-mcbsp-dai-0
No device for DAI omap-mcbsp-dai-1
No device for DAI omap-mcbsp-dai-2
No device for DAI omap-mcbsp-dai-3
No device for DAI omap-mcbsp-dai-4
overo SoC init
TWL4030 Audio Codec init
asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok
ALSA device list:
#0: overo (twl4030)
oprofile: using arm/armv7
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 15
Bluetooth: L2CAP ver 2.11
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO (Voice Link) ver 0.6
Bluetooth: SCO socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.10
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
ThumbEE CPU extension supported.
Power Management for TI OMAP3.
SmartReflex driver initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1
mmc0: mmc_rescan - card ocr from io_op=0x00000000, err = -110
fbcvt: 1024x768@60: CVT Name - .786M3-R
Console: switching to colour frame buffer device 128x48
clock: clksel_round_rate_div: dpll4_m4_ck target_rate 86400000
clock: new_div = 5, new_rate = 86400000
twl4030_rtc twl4030_rtc: setting system clock to 2000-01-01 00:00:00 UTC
(946684800)
JFFS2 notice: (1) jffs2_build_xattr_subsystem: complete building xattr
subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0
orphan) found.
VFS: Mounted root (jffs2 filesystem) on device 31:4.
Freeing init memory: 940K
mmc1: mmc_rescan - card ocr from io_op=0x90ff8000, err = 0
mmc1: new SDIO card at address 0001
INIT: version 2.86 booting
mount: error while loading shared libraries: libuuid.so.1: cannot open
shared object file: No such file or directory
grep: /proc/cmdline: No such file or directory
/etc/rcS.d/S01psplash: line 16: can't open /proc/cpuinfo: no such file
/etc/rcS.d/S01psplash: line 16: awk: not found
mount: error while loading shared libraries: libuuid.so.1: cannot open
shared object file: No such file or directory
/etc/rcS.d/S01psplash: line 21: /usr/bin/psplash: not found
mount: error while loading shared libraries: libuuid.so.1: cannot open
shared object file: No such file or directory
grep: /proc/filesystems: No such file or directory
mount: error while loading shared libraries: libuuid.so.1: cannot open
shared object file: No such file or directory
grep: /proc/mounts: No such file or directory
grep: /proc/mounts: No such file or directory
/etc/rcS.d/S10checkroot: line 199: awk: not found
Remounting root file system...
mount: error while loading shared libraries: libuuid.so.1: cannot open
shared object file: No such file or directory
mount: error while loading shared libraries: libuuid.so.1: cannot open
shared object file: No such file or directory
mount: error while loading shared libraries: libuuid.so.1: cannot open
shared object file: No such file or directory
/etc/init.d/rc: /etc/rcS.d/S35mountall.sh: line 17: logger: not found
/etc/init.d/rc: /etc/rcS.d/S35mountall.sh: line 58: awk: not found
/etc/init.d/rc: /etc/rcS.d/S37populate-volatile.sh: line 171: sort: not
found
grep: /proc/filesystems: No such file or directory
ALSA: Restoring mixer settings...
Setting up IP spoofing protection: FAILED.
Configuring network interfaces... NET: Registered protocol family 10
ifup: can't open '/var/run/ifstate': No such file or directory
done.
Starting portmap daemon: portmap.
grep: /proc/mounts: No such file or directory
hwclock: can't open '/dev/misc/rtc': No such file or directory
/etc/init.d/rc: /etc/rcS.d/S55bootmisc.sh: line 79: awk: not found
/etc/init.d/rc: /etc/rcS.d/S55bootmisc.sh: line 79: expr: not found
sh: 1: unknown operand
INIT: Entering runlevel: 5
Starting advanced power management daemon: start-stop-daemon: cannot start
/usr/sbin/apmd: No such file or directory
(failed.)
Starting syslogd/klogd: done
Starting Connection Manager
/etc/rc5.d/S22connman: line 40: connmand: not found
/etc/rc5.d/S23bluetooth: line 26: which: not found
/etc/rc5.d/S23bluetooth: line 27: which: not found
/etc/rc5.d/S23bluetooth: line 28: which: not found
/etc/rc5.d/S23bluetooth: line 29: which: not found
/etc/rc5.d/S23bluetooth: line 30: which: not found
/etc/rc5.d/S23bluetooth: line 31: which: not found
/etc/rc5.d/S23bluetooth: line 32: which: not found
Starting Bluetooth subsystem:
.
/etc/rc5.d/S50usb-gadget: line 15: usb-gadget: not found
ps: invalid option -- a
/etc/rc5.d/S81cups: line 176: awk: not found
BusyBox v1.13.2 (2009-03-09 11:27:58 PDT) multi-call binary

Usage: ps

Report process status

Options:
w Wide output

/etc/rc5.d/S81cups: line 232: /usr/sbin/cupsd: not found
cups: unable to start scheduler.
Starting GPE display manager: gpe-dm
/etc/rc5.d/S99gpe-dm: line 22: /usr/bin/gpe-dm: not found


*****************************************************************************************
*****************************************************************************************
*****************************************************************************************
*****************************************************************************************

Te execution stops here... after that... anything...
Does anyone knows what is the problem?

Thanks for Your help...

--
GARCIA CARRILLO Luis Rodolfo