If it built for you the second time with the 400Mhz option check that the /root/gumstix-buildroot/dl/gpsd-2.33.tar.gz file exists.

If it does then just try rebuilding again with the 600Mhz option.

This has been a know problem in the past  where the gpsd-2.33.tar.gz was getting downloaded to the gumstix-buildroot directory instead of gumstix-buildroot/dl. If that’s the case you can simply move it to the dl directory.

When building 1565 I didn’t get this problem although I have in the past.

 

Marc

 

 

 


From: gumstix-users-bounces@lists.sourceforge.net [mailto:gumstix-users-bounces@lists.sourceforge.net] On Behalf Of Sir Graham (EndoraSoft)
Sent: Monday, November 19, 2007 5:54 PM
To: General mailing list for gumstix users.
Subject: Re: [Gumstix-users]ProblemswithvertexXL6P+consoleLCD-vx+netmicroSD+ Samsung LCD Panel

 

Hi,

 

Thanks for you answer.

 

We try to "compile" the Build 1565 of Linux Kernel for Gumstix. I have now the Vertex XL6P (this works a 600Mhz, i think),

 

But when if I select this speed in the "make deconfig" the build stop with a error:

 

23:07:50 (27,3 KB/s) - `gpsd-2.33.tar.gz' saved [639348/639348]

 

zcat /root/gumstix-buildroot/dl/gpsd-2.33.tar.gz | tar -C /root/gumstix-buildroot/build_arm_nofpu   -xf -
zcat: /root/gumstix-buildroot/dl/gpsd-2.33.tar.gz: No such file or directory
toolchain/patch-kernel.sh /root/gumstix-buildroot/build_arm_nofpu/gpsd-2.33 package/gpsd gpsd-*.patch
Aborting.  '/root/gumstix-buildroot/build_arm_nofpu/gpsd-2.33' is not a directory.
make: *** [/root/gumstix-buildroot/build_arm_nofpu/gpsd-2.33/configure] Error 1

 

 

If I select a 400Mhz speed the build is correct. But this image is valid U-Boot + filesystem-image for the Vertex XL6P?

 

Anyboy knows about this problem?

 

I like Build the 1565 to resolve the problem with the LCD and the the driver SMC911....  (I hope).

 

Regards,

Sir Graham.

 

 

 

----- Original Message -----

Sent: Monday, November 19, 2007 10:09 PM

Subject: Re: [Gumstix-users] ProblemswithvertexXL6P+consoleLCD-vx+netmicroSD+ Samsung LCD Panel

 

Michael,

 

Just I just grabbed a fresh 1565 and ran

make defconfig;

make;

 

So whether that uses modules or static I’m not sure. I used the exact same image on my netCF-vx card by simply commenting out the smc911x line and uncommenting the smc91x line if that is any indication? That netCF eth0 worked fine, but it obviously doesn’t have the mwlan0 interface to contend with.

 

Warm boots stay stable unless I do ifconfig eth0 down/up; at which point I cannot get it to work again.

 

Marc

 

 

 


From: gumstix-users-bounces@lists.sourceforge.net [mailto:gumstix-users-bounces@lists.sourceforge.net] On Behalf Of Black, Michael
Sent: Monday, November 19, 2007 3:21 PM
To: General mailing list for gumstix users.
Subject: Re: [Gumstix-users] ProblemswithvertexXL6P+consoleLCD-vx+netmicroSD + Samsung LCD Panel

 

This sounds very clearly like an ordering or inter-statement timing problem in the initialization of the card.

 

Are you running the module version or statically compiled in?

 

Perhaps try the module version and see how it behave when you unload/load it.

 

Also, it wasn’t clear from your emails.

 

Are you unable to break a warm boot or does the “ifconfig eth0 down/up” break the warm boot?

 

___________________

Michael D. Black

Essex

black@essexcorp.com


From: gumstix-users-bounces@lists.sourceforge.net [mailto:gumstix-users-bounces@lists.sourceforge.net] On Behalf Of Marc Humphreys
Sent: Monday, November 19, 2007 2:11 PM
To: 'Marc Humphreys'; 'General mailing list for gumstix users.'
Subject: Re: [Gumstix-users] Problems withvertexXL6P+consoleLCD-vx+netmicroSD + Samsung LCD Panel

 

One small correction. I cold not break either interface after 10 WARM reboots. It just kept working.

A cold power on reset would introduce the issue again until a warm reboot was initiated.

 


From: Marc Humphreys [mailto:mhumphreys@logiclinkdesign.com]
Sent: Monday, November 19, 2007 3:05 PM
To: 'Marc Humphreys'; 'General mailing list for gumstix users.'
Subject: RE: [Gumstix-users] Problems with vertexXL6P+consoleLCD-vx+netmicroSD + Samsung LCD Panel

 

Sorry – previous message sent prematurely.

Here is the completed version.

 

OK – here is the testing and findings on 1565 with vertexXL6P+consoleLCD-vx+netmicroSD + Samsung LCD Panel including the wifi module so really netwifi_uSD.

 

It works but with one small caveat. ON initial cold power up the ifconfig shows both eth0 and mwal0 as configured ,however, I cannot use eth0 to ping a 192.168.16.x address or any wan address for that matter.

 

The good news is it works after a warm reboot and I could not break it after 10 cold reboots.

 

I retried the cold poweron and same thing happens – warm reboot fixes the problem.

I verified this at leat 5 times.

 

Here is the ifconfig output – after cold poweron reboot or warm – info is the same.

 

 

# ifconfig

eth0      Link encap:Ethernet  HWaddr AE:F7:51:56:49:D0

          inet addr:192.168.16.19  Bcast:0.0.0.0  Mask:255.255.255.0

          inet6 addr: fe80::acf7:51ff:fe56:49d0/64 Scope:Link

          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1

          RX packets:210 errors:0 dropped:0 overruns:0 frame:0

          TX packets:26 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:1000

          RX bytes:14658 (14.3 KiB)  TX bytes:6377 (6.2 KiB)

          Interrupt:131 Base address:0x2000 DMA chan:ff

 

lo        Link encap:Local Loopback

          inet addr:127.0.0.1  Mask:255.0.0.0

          inet6 addr: ::1/128 Scope:Host

          UP LOOPBACK RUNNING  MTU:16436  Metric:1

          RX packets:0 errors:0 dropped:0 overruns:0 frame:0

          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:0

          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

 

mwlan0    Link encap:Ethernet  HWaddr 00:0B:6B:0B:83:49

          inet addr:192.168.10.103  Bcast:0.0.0.0  Mask:255.255.255.0

          inet6 addr: fe80::20b:6bff:fe0b:8349/64 Scope:Link

          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1

          RX packets:42 errors:0 dropped:0 overruns:0 frame:0

          TX packets:20 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:1000

          RX bytes:2992 (2.9 KiB)  TX bytes:5705 (5.5 KiB)

          Interrupt:128

 

##########################################################

 

In the broken case if I do ifconfig down the ifconfig up I get the following:

 

# ifconfig eth0 up

Auto negotiation NOT supported

ADDRCONF(NETDEV_UP): eth0: link is not ready

 

 

For the working case if I ping and use the interface I have no problem, but if I take the interface down and backup I break it.

 

# ping 192.168.16.23

PING 192.168.16.23 (192.168.16.23): 56 data bytes

84 bytes from 192.168.16.23: icmp_seq=0 ttl=128 time=11.1 ms

 

--- 192.168.16.23 ping statistics ---

1 packets transmitted, 1 packets received, 0% packet loss

round-trip min/avg/max = 11.1/11.1/11.1 ms

# ifconfig eth0 down

# ifconfig eth0 up

Auto negotiation NOT supported

ADDRCONF(NETDEV_UP): eth0: link is not ready

# ping 192.168.16.23

PING 192.168.16.23 (192.168.16.23): 56 data bytes

 

--- 192.168.16.23 ping statistics ---

3 packets transmitted, 0 packets received, 100% packet loss

 

 

################################################################3

 

For the broken and working case here is the /tmp/message logs.

 

For the broken cold power up case:

 

# more /etc/messages

more: /etc/messages: No such file or directory

# more /tmp/messages

Dec 31 16:00:24 gumstix syslog.info syslogd started: BusyBox v1.1.2

Dec 31 16:00:25 gumstix daemon.info init: Starting pid 558, console /dev/null: '

/sbin/klogd'

Dec 31 16:00:25 gumstix user.notice kernel: klogd started: BusyBox v1.1.2 (2007.

11.19-01:23+0000)

Dec 31 16:00:25 gumstix user.notice kernel: Linux version 2.6.21gum (mhumphreys@

grandbaie) (gcc version 4.1.1) #1 Sun Nov 18 20:29:25 EST 2007

Dec 31 16:00:25 gumstix user.warn kernel: CPU: XScale-PXA270 [69054117] revision

 7 (ARMv5TE), cr=0000397f

Dec 31 16:00:25 gumstix user.warn kernel: Machine: The Gumstix Platform

Dec 31 16:00:25 gumstix user.warn kernel: Memory policy: ECC disabled, Data cach

e writeback

Dec 31 16:00:25 gumstix user.debug kernel: On node 0 totalpages: 32768

Dec 31 16:00:25 gumstix user.debug kernel:   DMA zone: 256 pages used for memmap

Dec 31 16:00:25 gumstix user.debug kernel:   DMA zone: 0 pages reserved

Dec 31 16:00:25 gumstix user.debug kernel:   DMA zone: 32512 pages, LIFO batch:7

Dec 31 16:00:25 gumstix user.debug kernel:   Normal zone: 0 pages used for memma

p

Dec 31 16:00:25 gumstix user.info kernel: Run Mode clock: 208.00MHz (*16)

Dec 31 16:00:25 gumstix user.info kernel: Turbo Mode clock: 624.00MHz (*3.0, act

ive)

Dec 31 16:00:25 gumstix user.info kernel: Memory clock: 104.00MHz (/2)

Dec 31 16:00:25 gumstix user.info kernel: System bus clock: 104.00MHz

Dec 31 16:00:25 gumstix user.warn kernel: CPU0: D VIVT undefined 5 cache

Dec 31 16:00:25 gumstix user.warn kernel: CPU0: I cache: 32768 bytes, associativ

ity 32, 32 byte lines, 32 sets

Dec 31 16:00:25 gumstix user.warn kernel: CPU0: D cache: 32768 bytes, associativ

ity 32, 32 byte lines, 32 sets

Dec 31 16:00:25 gumstix user.warn kernel: Built 1 zonelists.  Total pages: 32512

Dec 31 16:00:25 gumstix user.notice kernel: Kernel command line: console=ttyS0,1

15200n8 root=1f01 rootfstype=jffs2 reboot=cold,hard

Dec 31 16:00:25 gumstix user.warn kernel: PID hash table entries: 512 (order: 9,

 2048 bytes)

Dec 31 16:00:25 gumstix user.warn kernel: Console: colour dummy device 80x30

Dec 31 16:00:25 gumstix user.warn kernel: Dentry cache hash table entries: 16384

 (order: 4, 65536 bytes)

Dec 31 16:00:25 gumstix user.warn kernel: Inode-cache hash table entries: 8192 (

order: 3, 32768 bytes)

Dec 31 16:00:25 gumstix user.info kernel: Memory: 128MB = 128MB total

Dec 31 16:00:25 gumstix user.notice kernel: Memory: 127744KB available (1748K co

de, 192K data, 132K init)

Dec 31 16:00:25 gumstix user.debug kernel: Calibrating delay loop... 622.59 Bogo

MIPS (lpj=3112960)

Dec 31 16:00:25 gumstix user.warn kernel: Mount-cache hash table entries: 512

Dec 31 16:00:25 gumstix user.info kernel: CPU: Testing write buffer coherency: o

k

Dec 31 16:00:25 gumstix user.info kernel: NET: Registered protocol family 16

Dec 31 16:00:25 gumstix user.info kernel: NET: Registered protocol family 2

Dec 31 16:00:25 gumstix user.info kernel: Time: pxa_timer clocksource has been i

nstalled.

Dec 31 16:00:25 gumstix user.warn kernel: IP route cache hash table entries: 102

4 (order: 0, 4096 bytes)

Dec 31 16:00:25 gumstix user.warn kernel: TCP established hash table entries: 40

96 (order: 3, 32768 bytes)

Dec 31 16:00:25 gumstix user.warn kernel: TCP bind hash table entries: 4096 (ord

er: 2, 16384 bytes)

Dec 31 16:00:25 gumstix user.info kernel: TCP: Hash tables configured (establish

ed 4096 bind 4096)

Dec 31 16:00:25 gumstix user.info kernel: TCP reno registered

Dec 31 16:00:25 gumstix user.info kernel: JFFS2 version 2.2. (NAND) (SUMMARY)  (

C) 2001-2006 Red Hat, Inc.

Dec 31 16:00:25 gumstix user.info kernel: io scheduler noop registered

Dec 31 16:00:25 gumstix user.info kernel: io scheduler cfq registered (default)

Dec 31 16:00:25 gumstix user.warn kernel: Console: switching to colour frame buf

fer device 80x24

Dec 31 16:00:25 gumstix user.info kernel: pxa2xx-uart.0: ttyS0 at MMIO 0x4010000

0 (irq = 22) is a FFUART

Dec 31 16:00:25 gumstix user.info kernel: pxa2xx-uart.1: ttyS1 at MMIO 0x4020000

0 (irq = 21) is a BTUART

Dec 31 16:00:25 gumstix user.info kernel: pxa2xx-uart.2: ttyS2 at MMIO 0x4070000

0 (irq = 20) is a STUART

Dec 31 16:00:25 gumstix user.notice kernel: Probing Gumstix Flash ROM at physica

l address 0x00000000 (16-bit bankwidth)

Dec 31 16:00:25 gumstix user.info kernel: Gumstix Flash ROM: Found 1 x16 devices

 at 0x0 in 16-bit bank

Dec 31 16:00:25 gumstix user.debug kernel: Gumstix Flash ROM: Found an alias at

0x2000000 for the chip at 0x0

Dec 31 16:00:25 gumstix user.warn kernel:  Intel/Sharp Extended Query Table at 0

x010A

Dec 31 16:00:25 gumstix user.warn kernel:  Intel/Sharp Extended Query Table at 0

x010A

Dec 31 16:00:25 gumstix user.warn kernel:  Intel/Sharp Extended Query Table at 0

x010A

Dec 31 16:00:25 gumstix user.warn kernel:  Intel/Sharp Extended Query Table at 0

x010A

Dec 31 16:00:25 gumstix user.warn kernel:  Intel/Sharp Extended Query Table at 0

x010A

Dec 31 16:00:25 gumstix user.info kernel: Using buffer write method

Dec 31 16:00:25 gumstix user.notice kernel: cfi_cmdset_0001: Erase suspend on wr

ite enabled

Dec 31 16:00:25 gumstix user.debug kernel: erase region 0: offset=0x0,size=0x200

00,blocks=255

Dec 31 16:00:25 gumstix user.debug kernel: erase region 1: offset=0x1fe0000,size

=0x8000,blocks=4

Dec 31 16:00:25 gumstix user.warn kernel: Using static partitions on Gumstix Fla

sh ROM

Dec 31 16:00:25 gumstix user.notice kernel: Creating 3 MTD partitions on "Gumsti

x Flash ROM":

Dec 31 16:00:25 gumstix user.notice kernel: 0x00000000-0x00040000 : "Bootloader"

Dec 31 16:00:25 gumstix user.notice kernel: 0x00040000-0x01f00000 : "RootFS"

Dec 31 16:00:25 gumstix user.notice kernel: 0x01f00000-0x02000000 : "Kernel"

Dec 31 16:00:25 gumstix user.info kernel: TCP cubic registered

Dec 31 16:00:25 gumstix user.info kernel: XScale iWMMXt coprocessor detected.

Dec 31 16:00:25 gumstix user.warn kernel: VFS: Mounted root (jffs2 filesystem).

Dec 31 16:00:25 gumstix user.info kernel: Freeing init memory: 132K

Dec 31 16:00:25 gumstix user.info kernel: NET: Registered protocol family 1

Dec 31 16:00:25 gumstix user.info kernel: mmcblk0: mmc0:bcf6 SU02G 1985024KiB

Dec 31 16:00:25 gumstix user.info kernel:  mmcblk0: p1

Dec 31 16:00:25 gumstix user.warn kernel: eth0: LAN9117 (rev 1) at 0xc8872000 IR

Q 131

Dec 31 16:00:25 gumstix user.warn kernel: eth0: Ethernet addr: ae:f7:51:56:49:d0

Dec 31 16:00:25 gumstix user.debug kernel: eth0: LAN911x Internal PHY

Dec 31 16:00:25 gumstix user.warn kernel: Not netCF-vx board: using newer GPIO c

onfiguration

Dec 31 16:00:25 gumstix user.warn kernel: CPLD responded with: 00

Dec 31 16:00:25 gumstix user.info kernel: usbcore: registered new interface driv

er usbfs

Dec 31 16:00:25 gumstix user.info kernel: usbcore: registered new interface driv

er hub

Dec 31 16:00:25 gumstix user.info kernel: usbcore: registered new device driver

usb

Dec 31 16:00:25 gumstix user.debug kernel: ohci_hcd: 2006 August 04 USB 1.1 'Ope

n' Host Controller (OHCI) Driver

Dec 31 16:00:25 gumstix user.info kernel: pxa27x-ohci pxa27x-ohci: PXA27x OHCI

Dec 31 16:00:25 gumstix user.info kernel: pxa27x-ohci pxa27x-ohci: new USB bus r

egistered, assigned bus number 1

Dec 31 16:00:25 gumstix user.info kernel: pxa27x-ohci pxa27x-ohci: irq 3, io mem

 0x4c000000

Dec 31 16:00:25 gumstix user.info kernel: usb usb1: configuration #1 chosen from

 1 choice

Dec 31 16:00:25 gumstix user.info kernel: hub 1-0:1.0: USB hub found

Dec 31 16:00:25 gumstix user.info kernel: hub 1-0:1.0: 3 ports detected

Dec 31 16:00:25 gumstix user.notice kernel: pccard: PCMCIA card inserted into sl

ot 0

Dec 31 16:00:25 gumstix user.info kernel: usb 1-2: new full speed USB device usi

ng pxa27x-ohci and address 2

Dec 31 16:00:25 gumstix user.info kernel:

Dec 31 16:00:25 gumstix user.info kernel: hub 1-2:1.0: USB hub found

Dec 31 16:00:25 gumstix user.info kernel: hub 1-2:1.0: 4 ports detected

Dec 31 16:00:25 gumstix user.info kernel: eth0: link down

Dec 31 16:00:25 gumstix user.info kernel: NET: Registered protocol family 17

Dec 31 16:00:25 gumstix user.info kernel: usb 1-2.3: new full speed USB device u

sing pxa27x-ohci and address 3

Dec 31 16:00:25 gumstix user.info kernel: usb 1-2.3: configuration #1 chosen fro

m 1 choice

Dec 31 16:00:25 gumstix user.notice kernel: pccard: card ejected from slot 0

Dec 31 16:00:25 gumstix user.notice kernel: SCSI subsystem initialized

Dec 31 16:00:25 gumstix user.warn kernel: cfio: module license 'unspecified' tai

nts kernel.

Dec 31 16:00:25 gumstix user.info kernel: usb 1-2.4: new low speed USB device us

ing pxa27x-ohci and address 4

Dec 31 16:00:25 gumstix user.info kernel: Initializing USB Mass Storage driver..

.

Dec 31 16:00:25 gumstix user.info kernel: usb 1-2.4: configuration #1 chosen fro

m 1 choice

Dec 31 16:00:25 gumstix user.info kernel: scsi0 : SCSI emulation for USB Mass St

orage devices

Dec 31 16:00:25 gumstix user.info kernel: usbcore: registered new interface driv

er usb-storage

Dec 31 16:00:25 gumstix user.info kernel: USB Mass Storage support registered.

Dec 31 16:00:25 gumstix user.debug kernel: usb-storage: device found at 3

Dec 31 16:00:25 gumstix user.debug kernel: usb-storage: waiting for device to se

ttle before scanning

Dec 31 16:00:25 gumstix user.info kernel: input: Logitech Logitech USB Keyboard

as /class/input/input0

Dec 31 16:00:25 gumstix user.info kernel: input: USB HID v1.10 Keyboard [Logitec

h Logitech USB Keyboard] on usb-pxa27x-2.4

Dec 31 16:00:25 gumstix user.info kernel: usbcore: registered new interface driv

er usbhid

Dec 31 16:00:25 gumstix user.info kernel: drivers/usb/input/hid-core.c: v2.6:USB

 HID core driver

Dec 31 16:00:25 gumstix user.notice kernel: pccard: PCMCIA card inserted into sl

ot 0

Dec 31 16:00:25 gumstix user.notice kernel: pcmcia: registering new device pcmci

a0.0

Dec 31 16:00:25 gumstix user.warn kernel: Before register driver

Dec 31 16:00:25 gumstix user.warn kernel: Entering cf_attach()

Dec 31 16:00:25 gumstix user.warn kernel: pcmcia: request for exclusive IRQ coul

d not be fulfilled.

Dec 31 16:00:25 gumstix user.warn kernel: pcmcia: the driver needs updating to s

upported shared IRQ lines.

Dec 31 16:00:25 gumstix user.info kernel: eth0: link up, 100Mbps, full-duplex, l

pa 0x05E1

Dec 31 16:00:25 gumstix user.warn kernel: BasePort1=0xc8880000, AssignedIRQ=128

Dec 31 16:00:25 gumstix user.warn kernel: After calling wlan_add_card function

Dec 31 16:00:25 gumstix user.warn kernel: After register driver

Dec 31 16:00:25 gumstix user.info kernel: NET: Registered protocol family 10

Dec 31 16:00:25 gumstix user.info kernel: Mobile IPv6

Dec 31 16:00:25 gumstix user.notice kernel: scsi 0:0:0:0: Direct-Access

     USB DISK 20X     PMAP PQ: 0 ANSI: 0 CCS

Dec 31 16:00:25 gumstix user.debug kernel: usb-storage: device scan complete

Dec 31 16:00:25 gumstix user.notice kernel: SCSI device sda: 985088 512-byte hdw

r sectors (504 MB)

Dec 31 16:00:25 gumstix user.notice kernel: sda: Write Protect is off

Dec 31 16:00:25 gumstix user.debug kernel: sda: Mode Sense: 23 00 00 00

Dec 31 16:00:25 gumstix user.err kernel: sda: assuming drive cache: write throug

h

Dec 31 16:00:25 gumstix user.notice kernel: SCSI device sda: 985088 512-byte hdw

r sectors (504 MB)

Dec 31 16:00:25 gumstix user.notice kernel: sda: Write Protect is off

Dec 31 16:00:25 gumstix user.debug kernel: sda: Mode Sense: 23 00 00 00

Dec 31 16:00:25 gumstix user.err kernel: sda: assuming drive cache: write throug

h

Dec 31 16:00:25 gumstix user.info kernel:  sda: sda1

Dec 31 16:00:25 gumstix user.notice kernel: sd 0:0:0:0: Attached scsi removable

disk sda

Dec 31 16:00:32 gumstix user.debug kernel: mwlan0: no IPv6 routers present

Dec 31 16:00:33 gumstix user.debug kernel: eth0: no IPv6 routers present

Dec 31 16:03:57 gumstix auth.info login[553]: root login  on `ttyS0'

Dec 31 16:04:25 gumstix user.info kernel: Auto negotiation NOT supported

Dec 31 16:04:25 gumstix user.info kernel: ADDRCONF(NETDEV_UP): eth0: link is not

 ready

 

For the working warm reset case:

 

 

 

 

Here is the output from two ping to different subnets. Each subnet is separated via a firewall so each is only accessible via its respective interface.

84 bytes from 192.168.16.23: icmp_seq=7 ttl=128 time=1.3 ms

84 bytes from 192.168.10.1: icmp_seq=1 ttl=64 time=10.0 ms

84 bytes from 192.168.16.23: icmp_seq=8 ttl=128 time=1.3 ms

84 bytes from 192.168.10.1: icmp_seq=2 ttl=64 time=10.0 ms

84 bytes from 192.168.16.23: icmp_seq=9 ttl=128 time=1.6 ms

84 bytes from 192.168.10.1: icmp_seq=3 ttl=64 time=4.0 ms

84 bytes from 192.168.16.23: icmp_seq=10 ttl=128 time=1.3 ms

84 bytes from 192.168.10.1: icmp_seq=4 ttl=64 time=9.9 ms

84 bytes from 192.168.16.23: icmp_seq=11 ttl=128 time=1.3 ms

84 bytes from 192.168.10.1: icmp_seq=5 ttl=64 time=10.0 ms

 

Did the same beating with running directFB testing and files transfers on the 192.168.16.x interface. Firewall to 192.168.10.x prevents scp testing currently. I was able to access the default web page on the gumstix though at both 192.168.16.19 and 192.168.10.103.

 

Not sure what the difference is between the cold power on resent a warm reboot. Here are the two respect boot logs as captured in /tmp/messages

 

 

# more /tmp/messages

Dec 31 16:00:24 gumstix syslog.info syslogd started: BusyBox v1.1.2

Dec 31 16:00:24 gumstix daemon.info init: Starting pid 563, console /dev/null: '

/sbin/klogd'

Dec 31 16:00:24 gumstix user.notice kernel: klogd started: BusyBox v1.1.2 (2007.

11.19-01:23+0000)

Dec 31 16:00:24 gumstix user.notice kernel: Linux version 2.6.21gum (mhumphreys@

grandbaie) (gcc version 4.1.1) #1 Sun Nov 18 20:29:25 EST 2007

Dec 31 16:00:24 gumstix user.warn kernel: CPU: XScale-PXA270 [69054117] revision

 7 (ARMv5TE), cr=0000397f

Dec 31 16:00:24 gumstix user.warn kernel: Machine: The Gumstix Platform

Dec 31 16:00:24 gumstix user.warn kernel: Memory policy: ECC disabled, Data cach

e writeback

Dec 31 16:00:24 gumstix user.debug kernel: On node 0 totalpages: 32768

Dec 31 16:00:24 gumstix user.debug kernel:   DMA zone: 256 pages used for memmap

Dec 31 16:00:24 gumstix user.debug kernel:   DMA zone: 0 pages reserved

Dec 31 16:00:24 gumstix user.debug kernel:   DMA zone: 32512 pages, LIFO batch:7

Dec 31 16:00:24 gumstix user.debug kernel:   Normal zone: 0 pages used for memma

p

Dec 31 16:00:24 gumstix user.info kernel: Run Mode clock: 208.00MHz (*16)

Dec 31 16:00:24 gumstix user.info kernel: Turbo Mode clock: 624.00MHz (*3.0, act

ive)

Dec 31 16:00:24 gumstix user.info kernel: Memory clock: 104.00MHz (/2)

Dec 31 16:00:24 gumstix user.info kernel: System bus clock: 104.00MHz

Dec 31 16:00:24 gumstix user.warn kernel: CPU0: D VIVT undefined 5 cache

Dec 31 16:00:24 gumstix user.warn kernel: CPU0: I cache: 32768 bytes, associativ

ity 32, 32 byte lines, 32 sets

Dec 31 16:00:24 gumstix user.warn kernel: CPU0: D cache: 32768 bytes, associativ

ity 32, 32 byte lines, 32 sets

Dec 31 16:00:24 gumstix user.warn kernel: Built 1 zonelists.  Total pages: 32512

Dec 31 16:00:24 gumstix user.notice kernel: Kernel command line: console=ttyS0,1

15200n8 root=1f01 rootfstype=jffs2 reboot=cold,hard

Dec 31 16:00:24 gumstix user.warn kernel: PID hash table entries: 512 (order: 9,

 2048 bytes)

Dec 31 16:00:24 gumstix user.warn kernel: Console: colour dummy device 80x30

Dec 31 16:00:24 gumstix user.warn kernel: Dentry cache hash table entries: 16384

 (order: 4, 65536 bytes)

Dec 31 16:00:24 gumstix user.warn kernel: Inode-cache hash table entries: 8192 (

order: 3, 32768 bytes)

Dec 31 16:00:24 gumstix user.info kernel: Memory: 128MB = 128MB total

Dec 31 16:00:24 gumstix user.notice kernel: Memory: 127744KB available (1748K co

de, 192K data, 132K init)

Dec 31 16:00:24 gumstix user.debug kernel: Calibrating delay loop... 622.59 Bogo

MIPS (lpj=3112960)

Dec 31 16:00:24 gumstix user.warn kernel: Mount-cache hash table entries: 512

Dec 31 16:00:24 gumstix user.info kernel: CPU: Testing write buffer coherency: o

k

Dec 31 16:00:24 gumstix user.info kernel: NET: Registered protocol family 16

Dec 31 16:00:24 gumstix user.info kernel: NET: Registered protocol family 2

Dec 31 16:00:24 gumstix user.info kernel: Time: pxa_timer clocksource has been i

nstalled.

Dec 31 16:00:24 gumstix user.warn kernel: IP route cache hash table entries: 102

4 (order: 0, 4096 bytes)

Dec 31 16:00:24 gumstix user.warn kernel: TCP established hash table entries: 40

96 (order: 3, 32768 bytes)

Dec 31 16:00:24 gumstix user.warn kernel: TCP bind hash table entries: 4096 (ord

er: 2, 16384 bytes)

Dec 31 16:00:24 gumstix user.info kernel: TCP: Hash tables configured (establish

ed 4096 bind 4096)

Dec 31 16:00:24 gumstix user.info kernel: TCP reno registered

Dec 31 16:00:24 gumstix user.info kernel: JFFS2 version 2.2. (NAND) (SUMMARY)  (

C) 2001-2006 Red Hat, Inc.

Dec 31 16:00:24 gumstix user.info kernel: io scheduler noop registered

Dec 31 16:00:24 gumstix user.info kernel: io scheduler cfq registered (default)

Dec 31 16:00:24 gumstix user.warn kernel: Console: switching to colour frame buf

fer device 80x24

Dec 31 16:00:24 gumstix user.info kernel: pxa2xx-uart.0: ttyS0 at MMIO 0x4010000

0 (irq = 22) is a FFUART

Dec 31 16:00:24 gumstix user.info kernel: pxa2xx-uart.1: ttyS1 at MMIO 0x4020000

0 (irq = 21) is a BTUART

Dec 31 16:00:24 gumstix user.info kernel: pxa2xx-uart.2: ttyS2 at MMIO 0x4070000

0 (irq = 20) is a STUART

Dec 31 16:00:24 gumstix user.notice kernel: Probing Gumstix Flash ROM at physica

l address 0x00000000 (16-bit bankwidth)

Dec 31 16:00:24 gumstix user.info kernel: Gumstix Flash ROM: Found 1 x16 devices

 at 0x0 in 16-bit bank

Dec 31 16:00:24 gumstix user.debug kernel: Gumstix Flash ROM: Found an alias at

0x2000000 for the chip at 0x0

Dec 31 16:00:24 gumstix user.warn kernel:  Intel/Sharp Extended Query Table at 0

x010A

Dec 31 16:00:24 gumstix user.warn kernel:  Intel/Sharp Extended Query Table at 0

x010A

Dec 31 16:00:24 gumstix user.warn kernel:  Intel/Sharp Extended Query Table at 0

x010A

Dec 31 16:00:24 gumstix user.warn kernel:  Intel/Sharp Extended Query Table at 0

x010A

Dec 31 16:00:24 gumstix user.warn kernel:  Intel/Sharp Extended Query Table at 0

x010A

Dec 31 16:00:24 gumstix user.info kernel: Using buffer write method

Dec 31 16:00:24 gumstix user.notice kernel: cfi_cmdset_0001: Erase suspend on wr

ite enabled

Dec 31 16:00:24 gumstix user.debug kernel: erase region 0: offset=0x0,size=0x200

00,blocks=255

Dec 31 16:00:24 gumstix user.debug kernel: erase region 1: offset=0x1fe0000,size

=0x8000,blocks=4

Dec 31 16:00:24 gumstix user.warn kernel: Using static partitions on Gumstix Fla

sh ROM

Dec 31 16:00:24 gumstix user.notice kernel: Creating 3 MTD partitions on "Gumsti

x Flash ROM":

Dec 31 16:00:24 gumstix user.notice kernel: 0x00000000-0x00040000 : "Bootloader"

Dec 31 16:00:24 gumstix user.notice kernel: 0x00040000-0x01f00000 : "RootFS"

Dec 31 16:00:24 gumstix user.notice kernel: 0x01f00000-0x02000000 : "Kernel"

Dec 31 16:00:24 gumstix user.info kernel: TCP cubic registered

Dec 31 16:00:24 gumstix user.info kernel: XScale iWMMXt coprocessor detected.

Dec 31 16:00:24 gumstix user.warn kernel: VFS: Mounted root (jffs2 filesystem).

Dec 31 16:00:24 gumstix user.info kernel: Freeing init memory: 132K

Dec 31 16:00:24 gumstix user.info kernel: NET: Registered protocol family 1

Dec 31 16:00:24 gumstix user.info kernel: mmcblk0: mmc0:bcf6 SU02G 1985024KiB

Dec 31 16:00:24 gumstix user.info kernel:  mmcblk0: p1

Dec 31 16:00:24 gumstix user.warn kernel: eth0: LAN9117 (rev 1) at 0xc8872000 IR

Q 131

Dec 31 16:00:24 gumstix user.warn kernel: eth0: Ethernet addr: ae:f7:51:56:49:d0

Dec 31 16:00:24 gumstix user.debug kernel: eth0: LAN911x Internal PHY

Dec 31 16:00:24 gumstix user.warn kernel: Not netCF-vx board: using newer GPIO c

onfiguration

Dec 31 16:00:24 gumstix user.warn kernel: CPLD responded with: 00

Dec 31 16:00:24 gumstix user.info kernel: usbcore: registered new interface driv

er usbfs

Dec 31 16:00:24 gumstix user.info kernel: usbcore: registered new interface driv

er hub

Dec 31 16:00:24 gumstix user.info kernel: usbcore: registered new device driver

usb

Dec 31 16:00:24 gumstix user.debug kernel: ohci_hcd: 2006 August 04 USB 1.1 'Ope

n' Host Controller (OHCI) Driver

Dec 31 16:00:24 gumstix user.info kernel: pxa27x-ohci pxa27x-ohci: PXA27x OHCI

Dec 31 16:00:24 gumstix user.info kernel: pxa27x-ohci pxa27x-ohci: new USB bus r

egistered, assigned bus number 1

Dec 31 16:00:24 gumstix user.info kernel: pxa27x-ohci pxa27x-ohci: irq 3, io mem

 0x4c000000

Dec 31 16:00:24 gumstix user.info kernel: usb usb1: configuration #1 chosen from

 1 choice

Dec 31 16:00:24 gumstix user.info kernel: hub 1-0:1.0: USB hub found

Dec 31 16:00:24 gumstix user.info kernel: hub 1-0:1.0: 3 ports detected

Dec 31 16:00:24 gumstix user.notice kernel: pccard: PCMCIA card inserted into sl

ot 0

Dec 31 16:00:24 gumstix user.info kernel: usb 1-2: new full speed USB device usi

ng pxa27x-ohci and address 2

Dec 31 16:00:24 gumstix user.info kernel:

Dec 31 16:00:24 gumstix user.info kernel: hub 1-2:1.0: USB hub found

Dec 31 16:00:24 gumstix user.info kernel: hub 1-2:1.0: 4 ports detected

Dec 31 16:00:24 gumstix user.info kernel: eth0: link down

Dec 31 16:00:24 gumstix user.info kernel: usb 1-2.3: new full speed USB device u

sing pxa27x-ohci and address 3

Dec 31 16:00:24 gumstix user.info kernel: NET: Registered protocol family 17

Dec 31 16:00:24 gumstix user.info kernel: usb 1-2.3: configuration #1 chosen fro

m 1 choice

Dec 31 16:00:24 gumstix user.notice kernel: SCSI subsystem initialized

Dec 31 16:00:24 gumstix user.info kernel: Initializing USB Mass Storage driver..

.

Dec 31 16:00:24 gumstix user.info kernel: usb 1-2.4: new low speed USB device us

ing pxa27x-ohci and address 4

Dec 31 16:00:24 gumstix user.info kernel: usb 1-2.4: configuration #1 chosen fro

m 1 choice

Dec 31 16:00:24 gumstix user.notice kernel: pccard: card ejected from slot 0

Dec 31 16:00:24 gumstix user.info kernel: scsi0 : SCSI emulation for USB Mass St

orage devices

Dec 31 16:00:24 gumstix user.info kernel: usbcore: registered new interface driv

er usb-storage

Dec 31 16:00:24 gumstix user.info kernel: USB Mass Storage support registered.

Dec 31 16:00:24 gumstix user.debug kernel: usb-storage: device found at 3

Dec 31 16:00:24 gumstix user.debug kernel: usb-storage: waiting for device to se

ttle before scanning

Dec 31 16:00:24 gumstix user.warn kernel: cfio: module license 'unspecified' tai

nts kernel.

Dec 31 16:00:24 gumstix user.info kernel: input: Logitech Logitech USB Keyboard

as /class/input/input0

Dec 31 16:00:24 gumstix user.info kernel: input: USB HID v1.10 Keyboard [Logitec

h Logitech USB Keyboard] on usb-pxa27x-2.4

Dec 31 16:00:24 gumstix user.info kernel: usbcore: registered new interface driv

er usbhid

Dec 31 16:00:24 gumstix user.info kernel: drivers/usb/input/hid-core.c: v2.6:USB

 HID core driver

Dec 31 16:00:24 gumstix user.notice kernel: pccard: PCMCIA card inserted into sl

ot 0

Dec 31 16:00:24 gumstix user.notice kernel: pcmcia: registering new device pcmci

a0.0

Dec 31 16:00:24 gumstix user.info kernel: eth0: link up, 100Mbps, full-duplex, l

pa 0x05E1

Dec 31 16:00:24 gumstix user.warn kernel: Before register driver

Dec 31 16:00:24 gumstix user.warn kernel: Entering cf_attach()

Dec 31 16:00:24 gumstix user.warn kernel: pcmcia: request for exclusive IRQ coul

d not be fulfilled.

Dec 31 16:00:24 gumstix user.warn kernel: pcmcia: the driver needs updating to s

upported shared IRQ lines.

Dec 31 16:00:24 gumstix user.warn kernel: BasePort1=0xc8880000, AssignedIRQ=128

Dec 31 16:00:24 gumstix user.warn kernel: After calling wlan_add_card function

Dec 31 16:00:24 gumstix user.warn kernel: After register driver

Dec 31 16:00:24 gumstix user.info kernel: NET: Registered protocol family 10

Dec 31 16:00:24 gumstix user.info kernel: Mobile IPv6

Dec 31 16:00:24 gumstix user.notice kernel: scsi 0:0:0:0: Direct-Access

     USB DISK 20X     PMAP PQ: 0 ANSI: 0 CCS

Dec 31 16:00:24 gumstix user.debug kernel: usb-storage: device scan complete

Dec 31 16:00:24 gumstix user.notice kernel: SCSI device sda: 985088 512-byte hdw

r sectors (504 MB)

Dec 31 16:00:24 gumstix user.notice kernel: sda: Write Protect is off

Dec 31 16:00:24 gumstix user.debug kernel: sda: Mode Sense: 23 00 00 00

Dec 31 16:00:24 gumstix user.err kernel: sda: assuming drive cache: write throug

h

Dec 31 16:00:24 gumstix user.notice kernel: SCSI device sda: 985088 512-byte hdw

r sectors (504 MB)

Dec 31 16:00:24 gumstix user.notice kernel: sda: Write Protect is off

Dec 31 16:00:24 gumstix user.debug kernel: sda: Mode Sense: 23 00 00 00

Dec 31 16:00:24 gumstix user.err kernel: sda: assuming drive cache: write throug

h

Dec 31 16:00:24 gumstix user.info kernel:  sda: sda1

Dec 31 16:00:24 gumstix user.notice kernel: sd 0:0:0:0: Attached scsi removable

disk sda

Dec 31 16:00:29 gumstix auth.info login[558]: root login  on `ttyS0'

Dec 31 16:00:31 gumstix user.debug kernel: eth0: no IPv6 routers present

Dec 31 16:00:32 gumstix user.debug kernel: mwlan0: no IPv6 routers present

 

 

The only difference I saw while quickly scanning the two logs is right at the end. Same message basically as

When after a warm reboot I take the interface down, and try to bring it back up. I’ll try run a diff on them to see what else shows up.

 

Not sure what to make of this yet other than it all seems to hold together after a warm reboot.

 

 

Marc

 


From: gumstix-users-bounces@lists.sourceforge.net [mailto:gumstix-users-bounces@lists.sourceforge.net] On Behalf Of Marc Humphreys
Sent: Monday, November 19, 2007 10:32 AM
To: 'General mailing list for gumstix users.'
Subject: Re: [Gumstix-users] Problems with vertexXL6P+consoleLCD-vx+netmicroSD + Samsung LCD Panel

 

Felix,

 

With 1565 and verdex XL6P+consoleLCD-vx+netmicroSD + Samsung LCD Panel minus the wifi module I was able to

 

successfully run directfb df_dok test, while scp’ing files to mmc, usb flash or local file system. USB keyboard and LCD terminal work too.

 

Setup as tested XL6P, netwifi_uSD (without wifi module), 2Gig Sandisk uSD card, ConsoleLCD-vx, Samsung LCD, unpowered USB HUB, with keyboard and usb flash drive attached.

 

Tftp from uboot did not work. This was expected as its uboot expecting to find the smc91c1111-0 device.

 

GUM> tftp a2000000 rootfs.arm_nofpu_base1565.jffs2

SMC91111: PHY auto-negotiate timed out

 

Warning: MAC addresses don't match:

        HW MAC address:  01:00:01:00:01:00

        "ethaddr" value: AE:F7:51:56:49:D0

Using MAC Address AE:F7:51:56:49:D0

Using SMC91C1111-0 device

TFTP from server 192.168.16.23; our IP address is 192.168.16.19

Filename 'rootfs.arm_nofpu_base1565.jffs2'.

Load address: 0xa2000000

Loading: *

Abort

 

Next I’ll attach the wifi module and retest – I may need to reconfigure my wireless router for quick and dirty test so may take a while.

 

Marc.

 


From: gumstix-users-bounces@lists.sourceforge.net [mailto:gumstix-users-bounces@lists.sourceforge.net] On Behalf Of Marc Humphreys
Sent: Monday, November 19, 2007 9:59 AM
To: 'General mailing list for gumstix users.'
Subject: Re: [Gumstix-users] Problems with vertex XL6P+consoleLCD-vx+netmicroSD + Samsung LCD Panel

 

Good news so far the 1565 build doesn’t break the netCF-vx hardware stack I’m currently using.

 

After commenting out the smc911x line and uncommenting  the smc91x line I was still able to

 

Run directfb test df_dok while, simultaneously doing scp to USB flash stick or  CF or local file system. USB keyboard also works.

 

Current setup is verdex XL6P, netCF-vx, ConsoleLCD-vx, Samsung LCD, unpowered USB HUB, with keyboard and usb flash drive attached.

 

Tftp also works from uboot using device SMC91C1111-0 as expected.

 

Next I’ll assembly the stack with netwifi-uSD, test it and post the results.

 

Marc

 


From: gumstix-users-bounces@lists.sourceforge.net [mailto:gumstix-users-bounces@lists.sourceforge.net] On Behalf Of Felix Duvallet
Sent: Monday, November 19, 2007 1:12 AM
To: General mailing list for gumstix users.
Subject: Re: [Gumstix-users] Problems with vertex XL6P +consoleLCD-vx+netmicroSD + Samsung LCD Panel

 

Hi Marc-

Although I finally got the verdex to boot (with LCD attached) by removing the wifi module, doing anything remotely related to the network (wired ethernet) seemed to kill the board immediately: ssh'ing from the gumstix (to another host or to localhost), ssh'ing from a computer to the gumstix (over ethernet), or sometimes even logging in via the console/LCD.  Needless to say, stress-testing becomes a moot point :)

Interestingly enough, directFB does not compile for me (I had to grab the sources directly from the directFB site -- the script seemed to fail when wget'ing them), so I can't really test that either.  Errors are below.

I'm still interested in knowing whether anyone has any success running both the LCD and some sort of internet at the same time, so please post your results when you get a chance to test it out.

Cheers,
Felix

In: /gumstix-buildroot/build_arm_nofpu/DirectFB-0.9.24/lib/direct
system.c:47: error: expected declaration specifiers or '...' before 'gettid'
system.c:62: warning: type defaults to 'int' in declaration of '_syscall0'
system.c:62: error: expected ',' or ';' before 'pid_t'
system.c: In function 'direct_pagesize':
system.c:71: error: 'PAGE_SIZE' undeclared (first use in this function)
system.c:71: error: (Each undeclared identifier is reported only once
system.c:71: error: for each function it appears in.)
system.c:72: warning: control reaches end of non-void function

On Nov 19, 2007 11:19 AM, Marc Humphreys <mhumphreys@logiclinkdesign.com> wrote:

Felix,

 

I know originally I got it to work with I think build 1339, but didn't do much testing and only had the gumstix logo and login working on he LCD, but I did not have the wifi module attached so never tried that. I've downloaded the latest 1565 and am building it tonight. I have to dismantle my hardware stack and reattach the netwifi-uSD card and dig up my wifi module to attach to it.

I'll definitely post my results, not sure exactly when that will happen, but hopefully in a day or two. How do you stress test both interfaces. Is it sufficient to ping both IP addresses from another machine or maybe start two separate ssh sessions to each ip with some large file transfer using scp?

 

To stress test the setup I porpose to do the following:

Run the directfb tests on the LCD – probably df_dok, while scp'ing two large files over the lan and wifi interfaces, one from uSD card and another from flash drive that's plugged into the USB hub (powered from the ConsoleLCD board). Usb keyboard will be tested as well also attached to the hub.

 

Marc

 


From: gumstix-users-bounces@lists.sourceforge.net [mailto:gumstix-users-bounces@lists.sourceforge.net] On Behalf Of Felix Duvallet
Sent: Sunday, November 18, 2007 6:42 PM


To: General mailing list for gumstix users.
Subject: Re: [Gumstix-users] Problems with vertex XL6P + consoleLCD-vx+netmicroSD + Samsung LCD Panel

 

I'd be interested in knowing whether you come across some of the same issues I've had with this hardware configuration (which is almost identical to mine).  I had issues getting the LCD and ethernet/wireless to work at the same time (I posted to the mailing list a few weeks ago: http://www.nabble.com/Verdex-fails-to-boot-if-both-LCD-and-netwifi-microSD-are-connected-tf4768919.html ).

In the event that everything (hopefully) works for you, post to the list so I will at least know I probably did something wrong.  Otherwise, if you're having issues booting, you may want to try using either the LCD or the netmicroSD stick (but not both).

Cheers,
Felix

On Nov 19, 2007 3:36 AM, Marc Humphreys <mhumphreys@logiclinkdesign.com> wrote:

I got my verdex about 6 weeks ago and it had u-boot 1.2 and that should be
good for flashing with the new partition map that is current supported in
the new buildroot versions. However, 1.2 as is will not support mmc on
verdex Netwifi-uSD card.. You'll need to build and apply the patch or wait
for Steve's testing on the latest build which if works will probably be 1565
or greater.

You can check your uboot version by stopping auto boot. Simply hit a key on
the console keyboard within 2 seconds.

Then at the GUM> prompt type ver


U-Boot 1.2.0 (May 16 2007 - 11:14:35) - PXA270@600 MHz - 1407

*** Welcome to Gumstix ***

DRAM:  128 MB
Flash: 32 MB
SMC91C1111-0
Net:   SMC91C1111-0
Hit any key to stop autoboot:  0
GUM> ver

U-Boot 1.2.0 (May 16 2007 - 11:14:35) - PXA270@600 MHz - 1407

*** Welcome to Gumstix ***
GUM>

If you let the gumstix boot you can check the build version.
By typing #more /etc/gumstix-release

# more /etc/gumstix-release
DISTRIB_ID='gumstix'
DISTRIB_DESCRIPTION=''
DISTRIB_RELEASE='1562'
DISTRIB_CODENAME=''
BUILD_DATE='Thu Nov 15 08:10:34 EST 2007'
BUILD_HOSTNAME='grandbaie'
#

Its probably 1410 which will be of little use to you. I'm almost sure
mmcinit won't work with 1410. I'd grab the latest should be 1564 or greater.
Not sure if patches are still required. I understand Steve is testing new
build which if successful will probably be 1565?

Marc




-----Original Message-----
From: gumstix-users-bounces@lists.sourceforge.net
[mailto:gumstix-users-bounces@lists.sourceforge.net] On Behalf Of Dave
Hylands
Sent: Sunday, November 18, 2007 11:45 AM
To: General mailing list for gumstix users.
Subject: Re: [Gumstix-users] Problems with vertex XL6P + consoleLCD-vx
+netmicroSD + Samsung LCD Panel

Hi Sir Graham,

> First the Ethernet of the netmicroSD donīt work, I see is possible because
> the driver SMC911 is not present and activate. :(
> The LCD donīt work also.
>
> Questions:
>
>     Is necessary Reflashing the Boot Loader ( u-boot.bin) to activate the
LCD
> panel?

I'm not sure.

>     gumstix-buildroot is the same to the Connex platform that the vertex
> platform?

It's the same source code tree, but you can only build it for connex
or verdex, not both at the same time.

>     To flash Root Filesystem and Kernel,  is possible use the microSD (in
> connex we use the MMC card to load the flash)?

It should be. You can test this from within u-boot by using the
mmcinit command and seeing if it recognizes the card. You can then do

fatls mmc 0

to list the files on the card.

You might need to update your u-boot first. I know that the latest
u-boot (or the 1533 u-boot I have precompiled) will work with the
microSD cards.

--
Dave Hylands
Vancouver, BC, Canada
http://www.DaveHylands.com/

-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft
Defy all challenges. Microsoft(R) Visual Studio 2005.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
_______________________________________________
gumstix-users mailing list
gumstix-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/gumstix-users



-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft
Defy all challenges. Microsoft(R) Visual Studio 2005.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
_______________________________________________
gumstix-users mailing list
gumstix-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/gumstix-users

 


-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft
Defy all challenges. Microsoft(R) Visual Studio 2005.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
_______________________________________________
gumstix-users mailing list
gumstix-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/gumstix-users

 

 

 

 

 

 

 

 

This electronic message and any files transmitted with it contain information which may be privileged and/or proprietary. The information is intended for use solely by the intended recipient(s). If you are not the intended recipient, be aware that any disclosure, copying, distribution or use of this information is prohibited. If you have received this electronic message in error, please advise the sender by reply email or by telephone (301-939-7000) and delete the message.


-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft
Defy all challenges. Microsoft(R) Visual Studio 2005.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/


_______________________________________________
gumstix-users mailing list
gumstix-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/gumstix-users