#395 I350 NETDEV WATCHDOG: (igb): transmit queue 5 timed out

closed
Todd Fujinaka
None
distro_driver
1
2014-11-17
2014-01-27
Eggie
No

Fresh-installed CentOS 6.5 on a Supermicro X9DRW-7TPF+, the following error appears in syslog/dmesg appears shortly afterward:

NETDEV WATCHDOG: eth0 (igb): transmit queue 5 timed out

It would wait awhile for the ethernet driver to reset itself, or one could do 'service network restart' to get it back quicker.

ethtool -i eth0 shows:

driver: igb
version: 5.0.5-k
firmware-version: 1.61, 0x8000090e
bus-info: 0000:09:00.0
supports-statistics: yes
supports-test: yes
supports-eeprom-access: yes
supports-register-dump: yes
supports-priv-flags: no

Full dump:

WARNING: at net/sched/sch_generic.c:261 dev_watchdog+0x26b/0x280() (Not tainted)
Hardware name: X9DRW-7TPF+
NETDEV WATCHDOG: eth0 (igb): transmit queue 5 timed out
Modules linked in: tpm_infineon nt3gd(U) cpufreq_ondemand acpi_cpufreq freq_table mperf ipt_REJECT nf_conntrack_ipv4 nf_defrag_ipv4 iptable_filter ip_tables ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 xt_state nf_conntrack ip6table_filter ip6_tables ipv6 microcode acpi_pad ses enclosure iTCO_wdt iTCO_vendor_support igb i2c_algo_bit ixgbe dca ptp pps_core mdio serio_raw i2c_i801 i2c_core sg lpc_ich mfd_core shpchp ext4 jbd2 mbcache aesni_intel ablk_helper cryptd lrw glue_helper aes_x86_64 aes_generic xts gf128mul dm_crypt sd_mod crc_t10dif aacraid sr_mod cdrom isci libsas scsi_transport_sas ahci wmi dm_mirror dm_region_hash dm_log dm_mod [last unloaded: nt3gd]
Pid: 4, comm: ksoftirqd/0 Not tainted 2.6.32-431.3.1.el6.x86_64 #1
Call Trace:
<IRQ> [<ffffffff81071e27>] ? warn_slowpath_common+0x87/0xc0
[<ffffffff81071f16>] ? warn_slowpath_fmt+0x46/0x50
[<ffffffff8147b75b>] ? dev_watchdog+0x26b/0x280
[<ffffffff810ec287>] ? cpu_quiet_msk+0x77/0x130
[<ffffffff810ecb5a>] ? rcu_process_callbacks+0x25a/0x350
[<ffffffff8147b4f0>] ? dev_watchdog+0x0/0x280
[<ffffffff81084b07>] ? run_timer_softirq+0x197/0x340
[<ffffffff8107a8e1>] ?
do_softirq+0xc1/0x1e0
[<ffffffff8100c30c>] ? call_softirq+0x1c/0x30
[<ffffffff8100c30c>] ? call_softirq+0x1c/0x30
<EOI> [<ffffffff8100fa75>] ? do_softirq+0x65/0xa0
[<ffffffff8107a4a0>] ? ksoftirqd+0x80/0x110
[<ffffffff8107a420>] ? ksoftirqd+0x0/0x110
[<ffffffff8109af06>] ? kthread+0x96/0xa0
[<ffffffff8100c20a>] ? child_rip+0xa/0x20
[<ffffffff8109ae70>] ? kthread+0x0/0xa0
[<ffffffff8100c200>] ? child_rip+0x0/0x20
---[ end trace eb47724bdd96b5d1 ]---
igb 0000:09:00.0: eth0: Reset adapter
igb: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX
igb 0000:09:00.0: eth0: Reset adapter
igb: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX
Bridge firewalling registered
device eth0 entered promiscuous mode

Full dmesg initialization:

igb: Intel(R) Gigabit Ethernet Network Driver - version 5.0.5-k
igb: Copyright (c) 2007-2013 Intel Corporation.
alloc irq_desc for 35 on node 0
alloc kstat_irqs on node 0
alloc irq_2_iommu on node 0
igb 0000:09:00.0: PCI INT A -> GSI 35 (level, low) -> IRQ 35
igb 0000:09:00.0: setting latency timer to 64
alloc irq_desc for 180 on node 0
alloc kstat_irqs on node 0
alloc irq_2_iommu on node 0
igb 0000:09:00.0: irq 180 for MSI/MSI-X
alloc irq_desc for 181 on node 0
alloc kstat_irqs on node 0
alloc irq_2_iommu on node 0
igb 0000:09:00.0: irq 181 for MSI/MSI-X
alloc irq_desc for 182 on node 0
alloc kstat_irqs on node 0
alloc irq_2_iommu on node 0
igb 0000:09:00.0: irq 182 for MSI/MSI-X
alloc irq_desc for 183 on node 0
alloc kstat_irqs on node 0
alloc irq_2_iommu on node 0
igb 0000:09:00.0: irq 183 for MSI/MSI-X
alloc irq_desc for 184 on node 0
alloc kstat_irqs on node 0
alloc irq_2_iommu on node 0
igb 0000:09:00.0: irq 184 for MSI/MSI-X
alloc irq_desc for 185 on node 0
alloc kstat_irqs on node 0
alloc irq_2_iommu on node 0
igb 0000:09:00.0: irq 185 for MSI/MSI-X
alloc irq_desc for 186 on node 0
alloc kstat_irqs on node 0
alloc irq_2_iommu on node 0
igb 0000:09:00.0: irq 186 for MSI/MSI-X
alloc irq_desc for 187 on node 0
alloc kstat_irqs on node 0
alloc irq_2_iommu on node 0
igb 0000:09:00.0: irq 187 for MSI/MSI-X
alloc irq_desc for 188 on node 0
alloc kstat_irqs on node 0
alloc irq_2_iommu on node 0
igb 0000:09:00.0: irq 188 for MSI/MSI-X
igb 0000:09:00.0: irq 180 for MSI/MSI-X
igb 0000:09:00.0: irq 181 for MSI/MSI-X
igb 0000:09:00.0: irq 182 for MSI/MSI-X
igb 0000:09:00.0: irq 183 for MSI/MSI-X
igb 0000:09:00.0: irq 184 for MSI/MSI-X
igb 0000:09:00.0: irq 185 for MSI/MSI-X
igb 0000:09:00.0: irq 186 for MSI/MSI-X
igb 0000:09:00.0: irq 187 for MSI/MSI-X
igb 0000:09:00.0: irq 188 for MSI/MSI-X
igb 0000:09:00.0: added PHC on eth0
igb 0000:09:00.0: Intel(R) Gigabit Ethernet Network Connection
igb 0000:09:00.0: eth0: (PCIe:5.0Gb/s:Width x4) 00:25:90:8b:14:f2
igb 0000:09:00.0: eth0: PBA No: 106100-000
igb 0000:09:00.0: Using MSI-X interrupts. 8 rx queue(s), 8 tx queue(s)
igb 0000:09:00.1: PCI INT B -> GSI 36 (level, low) -> IRQ 36
igb 0000:09:00.1: setting latency timer to 64
alloc irq_desc for 189 on node 0
alloc kstat_irqs on node 0
alloc irq_2_iommu on node 0
igb 0000:09:00.1: irq 189 for MSI/MSI-X
alloc irq_desc for 190 on node 0
alloc kstat_irqs on node 0
alloc irq_2_iommu on node 0
igb 0000:09:00.1: irq 190 for MSI/MSI-X
alloc irq_desc for 191 on node 0
alloc kstat_irqs on node 0
alloc irq_2_iommu on node 0
igb 0000:09:00.1: irq 191 for MSI/MSI-X
alloc irq_desc for 192 on node 0
alloc kstat_irqs on node 0
alloc irq_2_iommu on node 0
igb 0000:09:00.1: irq 192 for MSI/MSI-X
alloc irq_desc for 193 on node 0
alloc kstat_irqs on node 0
alloc irq_2_iommu on node 0
igb 0000:09:00.1: irq 193 for MSI/MSI-X
alloc irq_desc for 194 on node 0
alloc kstat_irqs on node 0
alloc irq_2_iommu on node 0
igb 0000:09:00.1: irq 194 for MSI/MSI-X
alloc irq_desc for 195 on node 0
alloc kstat_irqs on node 0
alloc irq_2_iommu on node 0
igb 0000:09:00.1: irq 195 for MSI/MSI-X
alloc irq_desc for 196 on node 0
alloc kstat_irqs on node 0
alloc irq_2_iommu on node 0
igb 0000:09:00.1: irq 196 for MSI/MSI-X
alloc irq_desc for 197 on node 0
alloc kstat_irqs on node 0
alloc irq_2_iommu on node 0
igb 0000:09:00.1: irq 197 for MSI/MSI-X
igb 0000:09:00.1: irq 189 for MSI/MSI-X
igb 0000:09:00.1: irq 190 for MSI/MSI-X
igb 0000:09:00.1: irq 191 for MSI/MSI-X
igb 0000:09:00.1: irq 192 for MSI/MSI-X
igb 0000:09:00.1: irq 193 for MSI/MSI-X
igb 0000:09:00.1: irq 194 for MSI/MSI-X
igb 0000:09:00.1: irq 195 for MSI/MSI-X
igb 0000:09:00.1: irq 196 for MSI/MSI-X
igb 0000:09:00.1: irq 197 for MSI/MSI-X
igb 0000:09:00.1: added PHC on eth1
igb 0000:09:00.1: Intel(R) Gigabit Ethernet Network Connection
igb 0000:09:00.1: eth1: (PCIe:5.0Gb/s:Width x4) 00:25:90:8b:14:f3
igb 0000:09:00.1: eth1: PBA No: 106100-000
igb 0000:09:00.1: Using MSI-X interrupts. 8 rx queue(s), 8 tx queue(s)
igb: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

Related

Bugs: #395

Discussion

1 2 > >> (Page 1 of 2)
  • John Ronciak
    John Ronciak
    2014-01-27

    Can you please try the latest igb driver from our Sourceforge site?
    http://e1000.sf.net

    Please let us know.

    Thanks

    Cheers, John
    On Jan 27, 2014 12:07 PM, "Eggie" egberts@users.sf.net wrote:


    Status: open
    Created: Mon Jan 27, 2014 07:07 PM UTC by Eggie
    Last Updated: Mon Jan 27, 2014 07:07 PM UTC
    Owner: nobody

    Fresh-installed CentOS 6.5 on a Supermicro X9DRW-7TPF+, the following
    error appears in syslog/dmesg appears shortly afterward:

    NETDEV WATCHDOG: eth0 (igb): transmit queue 5 timed out

    It would wait awhile for the ethernet driver to reset itself, or one could
    do 'service network restart' to get it back quicker.

    ethtool -i eth0 shows:

    driver: igb
    version: 5.0.5-k
    firmware-version: 1.61, 0x8000090e
    bus-info: 0000:09:00.0
    supports-statistics: yes
    supports-test: yes
    supports-eeprom-access: yes
    supports-register-dump: yes
    supports-priv-flags: no

    Full dump:

    WARNING: at net/sched/sch_generic.c:261 dev_watchdog+0x26b/0x280() (Not
    tainted)
    Hardware name: X9DRW-7TPF+
    NETDEV WATCHDOG: eth0 (igb): transmit queue 5 timed out
    Modules linked in: tpm_infineon nt3gd(U) cpufreq_ondemand acpi_cpufreq
    freq_table mperf ipt_REJECT nf_conntrack_ipv4 nf_defrag_ipv4 iptable_filter
    ip_tables ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 xt_state
    nf_conntrack ip6table_filter ip6_tables ipv6 microcode acpi_pad ses
    enclosure iTCO_wdt iTCO_vendor_support igb i2c_algo_bit ixgbe dca ptp
    pps_core mdio serio_raw i2c_i801 i2c_core sg lpc_ich mfd_core shpchp ext4
    jbd2 mbcache aesni_intel ablk_helper cryptd lrw glue_helper aes_x86_64
    aes_generic xts gf128mul dm_crypt sd_mod crc_t10dif aacraid sr_mod cdrom
    isci libsas scsi_transport_sas ahci wmi dm_mirror dm_region_hash dm_log
    dm_mod [last unloaded: nt3gd]
    Pid: 4, comm: ksoftirqd/0 Not tainted 2.6.32-431.3.1.el6.x86_64 #1
    Call Trace:
    [] ? warn_slowpath_common+0x87/0xc0
    [] ? warn_slowpath_fmt+0x46/0x50
    [] ? dev_watchdog+0x26b/0x280
    [] ? cpu_quiet_msk+0x77/0x130
    [] ?

    rcu_process_callbacks+0x25a/0x350 [] ? dev_watchdog+0x0/0x280 [] ?
    run_timer_softirq+0x197/0x340 [] ?
    do_softirq+0xc1/0x1e0
    [] ? call_softirq+0x1c/0x30
    [] ? call_softirq+0x1c/0x30
    [] ? do_softirq+0x65/0xa0
    [] ? ksoftirqd+0x80/0x110
    [] ? ksoftirqd+0x0/0x110
    [] ? kthread+0x96/0xa0
    [] ? child_rip+0xa/0x20
    [] ? kthread+0x0/0xa0
    [] ? child_rip+0x0/0x20
    ---[ end trace eb47724bdd96b5d1 ]---
    igb 0000:09:00.0: eth0: Reset adapter
    igb: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX
    igb 0000:09:00.0: eth0: Reset adapter
    igb: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX
    Bridge firewalling registered
    device eth0 entered promiscuous mode

    Full dmesg initialization:

    igb: Intel(R) Gigabit Ethernet Network Driver - version 5.0.5-k
    igb: Copyright (c) 2007-2013 Intel Corporation.
    alloc irq_desc for 35 on node 0
    alloc kstat_irqs on node 0
    alloc irq_2_iommu on node 0
    igb 0000:09:00.0: PCI INT A -> GSI 35 (level, low) -> IRQ 35
    igb 0000:09:00.0: setting latency timer to 64
    alloc irq_desc for 180 on node 0
    alloc kstat_irqs on node 0
    alloc irq_2_iommu on node 0
    igb 0000:09:00.0: irq 180 for MSI/MSI-X
    alloc irq_desc for 181 on node 0
    alloc kstat_irqs on node 0
    alloc irq_2_iommu on node 0
    igb 0000:09:00.0: irq 181 for MSI/MSI-X
    alloc irq_desc for 182 on node 0
    alloc kstat_irqs on node 0
    alloc irq_2_iommu on node 0
    igb 0000:09:00.0: irq 182 for MSI/MSI-X
    alloc irq_desc for 183 on node 0
    alloc kstat_irqs on node 0
    alloc irq_2_iommu on node 0
    igb 0000:09:00.0: irq 183 for MSI/MSI-X
    alloc irq_desc for 184 on node 0
    alloc kstat_irqs on node 0
    alloc irq_2_iommu on node 0
    igb 0000:09:00.0: irq 184 for MSI/MSI-X
    alloc irq_desc for 185 on node 0
    alloc kstat_irqs on node 0
    alloc irq_2_iommu on node 0
    igb 0000:09:00.0: irq 185 for MSI/MSI-X
    alloc irq_desc for 186 on node 0
    alloc kstat_irqs on node 0
    alloc irq_2_iommu on node 0
    igb 0000:09:00.0: irq 186 for MSI/MSI-X
    alloc irq_desc for 187 on node 0
    alloc kstat_irqs on node 0
    alloc irq_2_iommu on node 0
    igb 0000:09:00.0: irq 187 for MSI/MSI-X
    alloc irq_desc for 188 on node 0
    alloc kstat_irqs on node 0
    alloc irq_2_iommu on node 0
    igb 0000:09:00.0: irq 188 for MSI/MSI-X
    igb 0000:09:00.0: irq 180 for MSI/MSI-X
    igb 0000:09:00.0: irq 181 for MSI/MSI-X
    igb 0000:09:00.0: irq 182 for MSI/MSI-X
    igb 0000:09:00.0: irq 183 for MSI/MSI-X
    igb 0000:09:00.0: irq 184 for MSI/MSI-X
    igb 0000:09:00.0: irq 185 for MSI/MSI-X
    igb 0000:09:00.0: irq 186 for MSI/MSI-X
    igb 0000:09:00.0: irq 187 for MSI/MSI-X
    igb 0000:09:00.0: irq 188 for MSI/MSI-X
    igb 0000:09:00.0: added PHC on eth0
    igb 0000:09:00.0: Intel(R) Gigabit Ethernet Network Connection
    igb 0000:09:00.0: eth0: (PCIe:5.0Gb/s:Width x4) 00:25:90:8b:14:f2
    igb 0000:09:00.0: eth0: PBA No: 106100-000
    igb 0000:09:00.0: Using MSI-X interrupts. 8 rx queue(s), 8 tx queue(s)
    igb 0000:09:00.1: PCI INT B -> GSI 36 (level, low) -> IRQ 36
    igb 0000:09:00.1: setting latency timer to 64
    alloc irq_desc for 189 on node 0
    alloc kstat_irqs on node 0
    alloc irq_2_iommu on node 0
    igb 0000:09:00.1: irq 189 for MSI/MSI-X
    alloc irq_desc for 190 on node 0
    alloc kstat_irqs on node 0
    alloc irq_2_iommu on node 0
    igb 0000:09:00.1: irq 190 for MSI/MSI-X
    alloc irq_desc for 191 on node 0
    alloc kstat_irqs on node 0
    alloc irq_2_iommu on node 0
    igb 0000:09:00.1: irq 191 for MSI/MSI-X
    alloc irq_desc for 192 on node 0
    alloc kstat_irqs on node 0
    alloc irq_2_iommu on node 0
    igb 0000:09:00.1: irq 192 for MSI/MSI-X
    alloc irq_desc for 193 on node 0
    alloc kstat_irqs on node 0
    alloc irq_2_iommu on node 0
    igb 0000:09:00.1: irq 193 for MSI/MSI-X
    alloc irq_desc for 194 on node 0
    alloc kstat_irqs on node 0
    alloc irq_2_iommu on node 0
    igb 0000:09:00.1: irq 194 for MSI/MSI-X
    alloc irq_desc for 195 on node 0
    alloc kstat_irqs on node 0
    alloc irq_2_iommu on node 0
    igb 0000:09:00.1: irq 195 for MSI/MSI-X
    alloc irq_desc for 196 on node 0
    alloc kstat_irqs on node 0
    alloc irq_2_iommu on node 0
    igb 0000:09:00.1: irq 196 for MSI/MSI-X
    alloc irq_desc for 197 on node 0
    alloc kstat_irqs on node 0
    alloc irq_2_iommu on node 0
    igb 0000:09:00.1: irq 197 for MSI/MSI-X
    igb 0000:09:00.1: irq 189 for MSI/MSI-X
    igb 0000:09:00.1: irq 190 for MSI/MSI-X
    igb 0000:09:00.1: irq 191 for MSI/MSI-X
    igb 0000:09:00.1: irq 192 for MSI/MSI-X
    igb 0000:09:00.1: irq 193 for MSI/MSI-X
    igb 0000:09:00.1: irq 194 for MSI/MSI-X
    igb 0000:09:00.1: irq 195 for MSI/MSI-X
    igb 0000:09:00.1: irq 196 for MSI/MSI-X
    igb 0000:09:00.1: irq 197 for MSI/MSI-X
    igb 0000:09:00.1: added PHC on eth1
    igb 0000:09:00.1: Intel(R) Gigabit Ethernet Network Connection
    igb 0000:09:00.1: eth1: (PCIe:5.0Gb/s:Width x4) 00:25:90:8b:14:f3
    igb 0000:09:00.1: eth1: PBA No: 106100-000
    igb 0000:09:00.1: Using MSI-X interrupts. 8 rx queue(s), 8 tx queue(s)
    igb: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX
    ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready


    Sent from sourceforge.net because you indicated interest in
    https://sourceforge.net/p/e1000/bugs/395/

    To unsubscribe from further messages, please visit
    https://sourceforge.net/auth/subscriptions/

     

    Related

    Bugs: #395

    • Eggie
      Eggie
      2014-02-02

      Trying IGB 5.1.2 right now on CentOS 6.5.

      Struggling to get IGB 5.1.2 built with kernel-2.6.32-358.23.1.el6.x86_64.

      Reports cryptic message:
      Makefile:76: Kernel header files not in any of the expected location
      Makefile:77:
      Install the appropriate kernel development package
      Makefile:78: *** kernel-devel, for building kernel modules and try again. Stop.

      It's trying to look for /usr/src/linux-2.6.32-358.23.2.el6.x86_64
      But I don't have the 'x86_64' portion of subdirectory name.

      I have installed:
      wget http://vault.centos.org/6.4/os/x86_64/Packages/kernel-devel-2.6.32-358.el6.x86_64.rpm
      wget http://vault.centos.org/6.4/updates/Source/SPackages/kernel-2.6.32-358.el6.x86_64.rpm
      yum install kernel-devel kernel-headers
      tar xvfz igb-5.1.2.tgz
      cd igb-5.1.2/src
      make install
      # see above error message

      Finally got it to work, I cheated.
      cd /usr/src
      ln -s linux-2.6.32-358.23.2.el6 linux
      make config
      ...
      make
      cd igb-5.1.2/src
      make install

       
      Last edit: Eggie 2014-02-02
  • Todd Fujinaka
    Todd Fujinaka
    2014-01-27

    • assigned_to: Todd Fujinaka
     
  • Todd Fujinaka
    Todd Fujinaka
    2014-01-27

    Also, I'm not clear on what part you're running. Can you send the relevant parts of lspci -vvv run as root? You can just attach the whole thing if you want (it's easier for me to read that way).

    Thanks.

     
    • Todd Fujinaka
      Todd Fujinaka
      2014-01-27

      Duh. It's in the title of the bug. The lspci will still be useful, and probably a dump of the EEPROM settings as well.

      But John is right, the first thing to check is to see if the newest driver from sourceforge fixes the problem.

      Thanks.

       
      • Eggie
        Eggie
        2014-01-31

        EEPROM dump provided by 'ethtool -e eth0' on igb driver.

         
      • Eggie
        Eggie
        2014-01-31

        lspci -vvv of igb interface.

         
        Attachments
        • John Ronciak
          John Ronciak
          2014-01-31

          Why is eth0 going into promiscuous mode on start up? That seems a bit odd.
          Does the rest still happen if you don't have the system configured to do
          this? The reset only happens on eth0 correct?

          On Fri, Jan 31, 2014 at 7:28 AM, Eggie egberts@users.sf.net wrote:

          lspci -vvv of igb interface.

          Status: open
          Created: Mon Jan 27, 2014 07:07 PM UTC by Eggie
          Last Updated: Mon Jan 27, 2014 09:37 PM UTC
          Owner: Todd Fujinaka

          Fresh-installed CentOS 6.5 on a Supermicro X9DRW-7TPF+, the following
          error appears in syslog/dmesg appears shortly afterward:

          NETDEV WATCHDOG: eth0 (igb): transmit queue 5 timed out

          It would wait awhile for the ethernet driver to reset itself, or one could
          do 'service network restart' to get it back quicker.

          ethtool -i eth0 shows:

          driver: igb
          version: 5.0.5-k
          firmware-version: 1.61, 0x8000090e
          bus-info: 0000:09:00.0
          supports-statistics: yes
          supports-test: yes
          supports-eeprom-access: yes
          supports-register-dump: yes
          supports-priv-flags: no

          Full dump:

          WARNING: at net/sched/sch_generic.c:261 dev_watchdog+0x26b/0x280() (Not
          tainted)
          Hardware name: X9DRW-7TPF+
          NETDEV WATCHDOG: eth0 (igb): transmit queue 5 timed out
          Modules linked in: tpm_infineon nt3gd(U) cpufreq_ondemand acpi_cpufreq
          freq_table mperf ipt_REJECT nf_conntrack_ipv4 nf_defrag_ipv4 iptable_filter
          ip_tables ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 xt_state
          nf_conntrack ip6table_filter ip6_tables ipv6 microcode acpi_pad ses
          enclosure iTCO_wdt iTCO_vendor_support igb i2c_algo_bit ixgbe dca ptp
          pps_core mdio serio_raw i2c_i801 i2c_core sg lpc_ich mfd_core shpchp ext4
          jbd2 mbcache aesni_intel ablk_helper cryptd lrw glue_helper aes_x86_64
          aes_generic xts gf128mul dm_crypt sd_mod crc_t10dif aacraid sr_mod cdrom
          isci libsas scsi_transport_sas ahci wmi dm_mirror dm_region_hash dm_log
          dm_mod [last unloaded: nt3gd]
          Pid: 4, comm: ksoftirqd/0 Not tainted 2.6.32-431.3.1.el6.x86_64 #1
          Call Trace:
          [] ? warn_slowpath_common+0x87/0xc0
          [] ? warn_slowpath_fmt+0x46/0x50
          [] ? dev_watchdog+0x26b/0x280
          [] ? cpu_quiet_msk+0x77/0x130
          [] ?

          rcu_process_callbacks+0x25a/0x350 [] ? dev_watchdog+0x0/0x280 [] ?
          run_timer_softirq+0x197/0x340 [] ?
          do_softirq+0xc1/0x1e0
          [] ? call_softirq+0x1c/0x30
          [] ? call_softirq+0x1c/0x30
          [] ? do_softirq+0x65/0xa0
          [] ? ksoftirqd+0x80/0x110
          [] ? ksoftirqd+0x0/0x110
          [] ? kthread+0x96/0xa0
          [] ? child_rip+0xa/0x20
          [] ? kthread+0x0/0xa0
          [] ? child_rip+0x0/0x20
          ---[ end trace eb47724bdd96b5d1 ]---
          igb 0000:09:00.0: eth0: Reset adapter
          igb: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX
          igb 0000:09:00.0: eth0: Reset adapter
          igb: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX
          Bridge firewalling registered
          device eth0 entered promiscuous mode

          Full dmesg initialization:

          igb: Intel(R) Gigabit Ethernet Network Driver - version 5.0.5-k
          igb: Copyright (c) 2007-2013 Intel Corporation.
          alloc irq_desc for 35 on node 0
          alloc kstat_irqs on node 0
          alloc irq_2_iommu on node 0
          igb 0000:09:00.0: PCI INT A -> GSI 35 (level, low) -> IRQ 35
          igb 0000:09:00.0: setting latency timer to 64
          alloc irq_desc for 180 on node 0
          alloc kstat_irqs on node 0
          alloc irq_2_iommu on node 0
          igb 0000:09:00.0: irq 180 for MSI/MSI-X
          alloc irq_desc for 181 on node 0
          alloc kstat_irqs on node 0
          alloc irq_2_iommu on node 0
          igb 0000:09:00.0: irq 181 for MSI/MSI-X
          alloc irq_desc for 182 on node 0
          alloc kstat_irqs on node 0
          alloc irq_2_iommu on node 0
          igb 0000:09:00.0: irq 182 for MSI/MSI-X
          alloc irq_desc for 183 on node 0
          alloc kstat_irqs on node 0
          alloc irq_2_iommu on node 0
          igb 0000:09:00.0: irq 183 for MSI/MSI-X
          alloc irq_desc for 184 on node 0
          alloc kstat_irqs on node 0
          alloc irq_2_iommu on node 0
          igb 0000:09:00.0: irq 184 for MSI/MSI-X
          alloc irq_desc for 185 on node 0
          alloc kstat_irqs on node 0
          alloc irq_2_iommu on node 0
          igb 0000:09:00.0: irq 185 for MSI/MSI-X
          alloc irq_desc for 186 on node 0
          alloc kstat_irqs on node 0
          alloc irq_2_iommu on node 0
          igb 0000:09:00.0: irq 186 for MSI/MSI-X
          alloc irq_desc for 187 on node 0
          alloc kstat_irqs on node 0
          alloc irq_2_iommu on node 0
          igb 0000:09:00.0: irq 187 for MSI/MSI-X
          alloc irq_desc for 188 on node 0
          alloc kstat_irqs on node 0
          alloc irq_2_iommu on node 0
          igb 0000:09:00.0: irq 188 for MSI/MSI-X
          igb 0000:09:00.0: irq 180 for MSI/MSI-X
          igb 0000:09:00.0: irq 181 for MSI/MSI-X
          igb 0000:09:00.0: irq 182 for MSI/MSI-X
          igb 0000:09:00.0: irq 183 for MSI/MSI-X
          igb 0000:09:00.0: irq 184 for MSI/MSI-X
          igb 0000:09:00.0: irq 185 for MSI/MSI-X
          igb 0000:09:00.0: irq 186 for MSI/MSI-X
          igb 0000:09:00.0: irq 187 for MSI/MSI-X
          igb 0000:09:00.0: irq 188 for MSI/MSI-X
          igb 0000:09:00.0: added PHC on eth0
          igb 0000:09:00.0: Intel(R) Gigabit Ethernet Network Connection
          igb 0000:09:00.0: eth0: (PCIe:5.0Gb/s:Width x4) 00:25:90:8b:14:f2
          igb 0000:09:00.0: eth0: PBA No: 106100-000
          igb 0000:09:00.0: Using MSI-X interrupts. 8 rx queue(s), 8 tx queue(s)
          igb 0000:09:00.1: PCI INT B -> GSI 36 (level, low) -> IRQ 36
          igb 0000:09:00.1: setting latency timer to 64
          alloc irq_desc for 189 on node 0
          alloc kstat_irqs on node 0
          alloc irq_2_iommu on node 0
          igb 0000:09:00.1: irq 189 for MSI/MSI-X
          alloc irq_desc for 190 on node 0
          alloc kstat_irqs on node 0
          alloc irq_2_iommu on node 0
          igb 0000:09:00.1: irq 190 for MSI/MSI-X
          alloc irq_desc for 191 on node 0
          alloc kstat_irqs on node 0
          alloc irq_2_iommu on node 0
          igb 0000:09:00.1: irq 191 for MSI/MSI-X
          alloc irq_desc for 192 on node 0
          alloc kstat_irqs on node 0
          alloc irq_2_iommu on node 0
          igb 0000:09:00.1: irq 192 for MSI/MSI-X
          alloc irq_desc for 193 on node 0
          alloc kstat_irqs on node 0
          alloc irq_2_iommu on node 0
          igb 0000:09:00.1: irq 193 for MSI/MSI-X
          alloc irq_desc for 194 on node 0
          alloc kstat_irqs on node 0
          alloc irq_2_iommu on node 0
          igb 0000:09:00.1: irq 194 for MSI/MSI-X
          alloc irq_desc for 195 on node 0
          alloc kstat_irqs on node 0
          alloc irq_2_iommu on node 0
          igb 0000:09:00.1: irq 195 for MSI/MSI-X
          alloc irq_desc for 196 on node 0
          alloc kstat_irqs on node 0
          alloc irq_2_iommu on node 0
          igb 0000:09:00.1: irq 196 for MSI/MSI-X
          alloc irq_desc for 197 on node 0
          alloc kstat_irqs on node 0
          alloc irq_2_iommu on node 0
          igb 0000:09:00.1: irq 197 for MSI/MSI-X
          igb 0000:09:00.1: irq 189 for MSI/MSI-X
          igb 0000:09:00.1: irq 190 for MSI/MSI-X
          igb 0000:09:00.1: irq 191 for MSI/MSI-X
          igb 0000:09:00.1: irq 192 for MSI/MSI-X
          igb 0000:09:00.1: irq 193 for MSI/MSI-X
          igb 0000:09:00.1: irq 194 for MSI/MSI-X
          igb 0000:09:00.1: irq 195 for MSI/MSI-X
          igb 0000:09:00.1: irq 196 for MSI/MSI-X
          igb 0000:09:00.1: irq 197 for MSI/MSI-X
          igb 0000:09:00.1: added PHC on eth1
          igb 0000:09:00.1: Intel(R) Gigabit Ethernet Network Connection
          igb 0000:09:00.1: eth1: (PCIe:5.0Gb/s:Width x4) 00:25:90:8b:14:f3
          igb 0000:09:00.1: eth1: PBA No: 106100-000
          igb 0000:09:00.1: Using MSI-X interrupts. 8 rx queue(s), 8 tx queue(s)
          igb: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX
          ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready


          Sent from sourceforge.net because you indicated interest in
          https://sourceforge.net/p/e1000/bugs/395/

          To unsubscribe from further messages, please visit
          https://sourceforge.net/auth/subscriptions/

          --
          Cheers,
          John

           

          Related

          Bugs: #395

          • Eggie
            Eggie
            2014-02-02

            Mmmm, I must have done tcpdump -i eth. I do think that promiscuous syslog is unrelated.

             
  • Todd Fujinaka
    Todd Fujinaka
    2014-02-03

    So, you probably have the wrong kernel headers. "uname -a" will show you what kernel you're running. The headers need to match.

     
1 2 > >> (Page 1 of 2)