[Acx100-devel] hello

SourceForge Headquarters 225 Broadway Suite 1600 San Diego, CA 92101 +1 (858) 454-5900

Hello,

can I be of any assistance for testing?,.. I will keep watching for things 
to do.
I may be a little slow at times depending on work and the state of my 
systems.

I have included some information about adapters available to me,
Adapters I presently have to test are, a pcmcia Atheros adapter DWL-G650, an 
Airstation PCMCIA PCI bridge (just the bridge), two DWL-520+ cards (acx), 
some Hawking 54G cards (can't remember which computer they were in but they 
were either RA, ACX or PrismGT), possibly another card. I have a bluetooth 
adapter too if anyone wants to try some standards mixing..
in addition to the above I can halfinch some usb pen style adapters I have 
seen around, a pcmcia adapter probably containing the realtek wifi chip, an 
unknown chipset access point with WPA and WDS

In this building there is an operational prism based access point, I know 
already that the acx100 in this computer works with this access point in its 
present wep 128 configuration.

now that I have listed the above you know what I am able to attempt to use 
for testing and can give me instructions if you know what needs to be 
tested,

in case you are interested what I would like to do with some of the hardware 
I mentioned is create a local Metropolitan Area Network (I have some high 
gain omni directional antenna). to this end Master mode and ess features for 
WDS or else some other meshing system are of importance to me.
Of equal importance is getting the card to work with etherboot if at all 
possible (it has been achieved with prism from what i hear, but I don't know 
if that card needed firmware and so on).

In workstation:

0000:00:0b.0 Network controller: Texas Instruments ACX 100 22Mbps Wireless 
Interface
	Subsystem: D-Link System Inc DWL-520+ 22Mbps PCI Wireless Adapter
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- 
<MAbort- >SERR- <PERR-
	Latency: 64, Cache Line Size: 0x08 (32 bytes)
	Interrupt: pin A routed to IRQ 169
	Region 0: I/O ports at d000 [size=32]
	Region 1: Memory at cfffb000 (32-bit, non-prefetchable) [size=4K]
	Region 2: Memory at cffe0000 (32-bit, non-prefetchable) [size=64K]
	Capabilities: [40] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

in server:

0000:00:09.0 Network controller: Texas Instruments ACX 111 54Mbps Wireless 
Interface
	Subsystem: Abocom Systems Inc: Unknown device ab90
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- 
<MAbort- >SERR- <PERR-
	Latency: 64, Cache Line Size: 0x08 (32 bytes)
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at f3ffa000 (32-bit, non-prefetchable) [size=8K]
	Region 1: Memory at f3fa0000 (32-bit, non-prefetchable) [size=128K]
	Capabilities: [40] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:0b.0 Network controller: RaLink Ralink RT2500 802.11 Cardbus 
Reference Card (rev 01)
	Subsystem: Edimax Computer Co.: Unknown device 0b54
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- 
Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- 
<MAbort- >SERR- <PERR-
	Latency: 64, Cache Line Size: 0x08 (32 bytes)
	Interrupt: pin A routed to IRQ 5
	Region 0: Memory at f3ff8000 (32-bit, non-prefetchable) [size=8K]
	Capabilities: [40] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-