Work at SourceForge, help us to make it a better place! We have an immediate need for a Support Technician in our San Francisco or Denver office.

Close

Linksys vlynq and acx111

jb44
2005-07-19
2013-02-17
  • jb44
    jb44
    2005-07-19

    Hi

    We currently busy with the open source project for the AR7 devices. The linksys wag54g V2 uses a tnetw1130 card. The problem is there is no pci support only VLYNQ. Is anybody working on support for vlynq stuff or maybe want to help us out to support the acx driver on the ar7 devices.

    Thanks

     
    • Andreas Mohr
      Andreas Mohr
      2005-07-19

      Hi,

      hmm, I've never done anything with vlynq, only PCI/CardBus/USB.

      You could tell me whether you need to know something else about those cards and I'd probably be able to help then.

       
    • jb44
      jb44
      2005-07-19

      Hi Andreas

      Here is some extracts of some of the vlynq code. As u can see  there is alot of ACX111 stuff in there. Maybe somebody already did work on this.

      sangam_board_setup.c:#define VLYNQ_ACX111_MEM_OFFSET     0xC0000000  /* Physical address of ACX111 memory */
      sangam_board_setup.c:#define VLYNQ_ACX111_MEM_SIZE       0x00040000  /* Total size of the ACX111 memory   */
      sangam_board_setup.c:#define VLYNQ_ACX111_REG_OFFSET     0xF0000000  /* PHYS_ADDR of ACX111 control registers   */
      sangam_board_setup.c:#define VLYNQ_ACX111_REG_SIZE       0x00022000  /* Size of ACX111 registers area, MAC+PHY  */
      sangam_board_setup.c:#define ACX111_VL1_REMOTE_SIZE 0x1000000
      sangam_board_setup.c:                vlynqDevice0.remote_mem.RxOffset[0]  =  VLYNQ_ACX111_MEM_OFFSET;
      sangam_board_setup.c:                vlynqDevice0.remote_mem.RxSize[0]    =  VLYNQ_ACX111_MEM_SIZE;
      sangam_board_setup.c:                vlynqDevice0.remote_mem.RxOffset[1]  =  VLYNQ_ACX111_REG_OFFSET;
      sangam_board_setup.c:                vlynqDevice0.remote_mem.RxSize[1]    =  VLYNQ_ACX111_REG_SIZE;
      sangam_board_setup.c:                vlynqDevice0.local_mem.RxSize[0]     =  ACX111_VL1_REMOTE_SIZE;

       
    • Hello,

      I'm also interested in having acx111 working on the ar7 platform. In the meanwhile, linksys has released the TI AP development toolik with the full source code. Maybe it can be used as hardware specs for the acx111 driver.
      The full tarball is here:
      ftp://ftp.linksys.com/opensourcecode/wag54gV2/1.00.19/WAG54GV2-EU_v1.00.19_GPL.tgz
      after unpacking you will find src/router/ti_ap/AP-DK5.7.0.4.tar.gz which contains the above mentioned sourcecode.
      I hope it helps!

       
      • exovii
        exovii
        2005-09-29

        Tried to download through your link today, but no AP-DK5.7.0.4.tar.gz inside...
        Do you have another place where we could find it ?

        Thanks

         
      • exovii
        exovii
        2005-09-29

        Sorry, I found it, but in WAG54GV2_V1.00.19_GPL.tgz, not WAG54GV2-EU_v1.00.19_GPL.tgz as you said.

         
    • Any news about vlynq and acx111 ?

      I also have an AR7 router (under openwrt) and I really would enjoy Wifi support on it :)

       
    • heini66
      heini66
      2006-02-20

      some work has been done, may it helps anybody for the ar7 project...
      http://wiki.openwrt.org/AR7Port
      http://forum.openwrt.org/viewtopic.php?id=2654