IPMItool: 1.8.10 released
IPMItool provides a simple command-line interface to IPMI-enabled devices through an IPMIv1.5 or IPMIv2.0 LAN interface or Linux/Solaris kernel driver.
This release of ipmitool 1.8.10 was community driven:
* Fixed contrib build so the oem_ibm_sel_map file gets included in rpm builds again.
* Added support for Debian packages to be built from CVS
* Fix for sdr and sel timestamp reporting issues
* Fix for discrete sensor state print routines to address state bits 8-14
* Change ipmi_chassis_status() to non-static so it can be used externally
* Added retries to SOL keepalive
* Fix to stop sensor list command from reporting a failure due to missing sensor
* Fix bug in sdr free space reporting
* Add support for IANA number to vendor name conversion for many vendors
* Fix segfault bug in lan set command
* Fix bug in population of raw i2c wdata buffer
* Fix bug in ipmb sensor reading
* Fix misspellings, typos, incorrect strncmp lengths, white space
* Update/fix printed help and usages for many commands
* Add and update support for all commands in ipmitool man page
* Fix for lanplus session re-open when the target becomes unavailable following a fw upgrade activation
* Add support for watchdog timer shutoff, reset, and get info
* Add support for more ibm systems in oem_ibm_sel_map
* Add more JEDEC support info for DIMMs; decrease request size for DIMM FRU info to 16 bytes at a time to allow more DIMM FRUs to respond.
* Fix to change hpmfwupg to version 1.02; fix to reduce hpmfwupg buffer length more aggressively when no response from iol
* Fix HPM firmware activation via IOL; fake a timeout after IOL session re-open to force get upgrade status retry; Added retries on 0xD3 completion code
* Add support for freeipmi 0.6.0; adjust autoconf for changes
* Fix for oemval2str size
* Add support for product name resolution in mc info
* Fix FRU display format
* Added PICMG ekeying analyzer module support (ekanalyzer); display point to point physical connectivity and power supply information between carriers and AMC modules; display matched results of ekeying match between an on-carrier device and AMC module or between 2 AMC modules
* Fix AMC GUID display support
* Improved amcportstate operations
* Added resolution for new sensor types
* Fix segfault in SOL
* Fix bug that caused infinite loop on BMCs with empty SDRs
* Fix to move out Kontron OEM sensor resolution for other OEMs which could lead to bad event descriptions
* Add new FRU edit mode thereby allowing serial numbers, etc. to be changed; improvements to OEM edit mode
* Added SPD support for parms: channel number, max read size
* Add SDR support for adding SDR records from a dumped file, clearing SDR, adding partial SDR records
* Add updates and fixes to hpmfwupg: upload block size to 32 bytes for KCS, handle long response option, implement rollback override, garbage output fix
* Add double bridge lan support , fix bridging issue
* Add HPM support to pre-check which components need to be skipped
* Fix autodetection of maximum packet size when using IPMB
* Add new Kontron OEM command to set the BIOS boot option sequence
* Add support for dual-bridge/ dual send message
* Add auto-detect for local IPMB address using PICMG 2.X extension
* Add support for HPM.1 1.0 specification compliance
* Fix for improper lan/lanplus addressing
* Added transit_channel and transit_addr to ipmi_intf struct
* Fix bad password assertion bug due to rakp2 HMAC not being checked properly
* Added ability to interpret PPS shelf manager clia sel dump
* Corrected PICMG M7 state event definition macros
* Added FRU parsing enhancements
* Added "isol info", "isol set" and "isol activate" commands to support Intel IPMI v1.5 SOL functionality. Removed "isol setup" command.
* Fix bug in ipmi_lan_recv_packet() in lan and lanplus interfaces.
* Fix bug in "chassis poh" command.
* Fix HPM.1 upgrade to apply to only given component when instructed to do so
* Added configure auto-detection if dual bridge extension is supported by OpenIPMI
2008-08-28 20:30:22 UTC by carolh
