From: Martin W. <mar...@gm...> - 2010-11-13 18:35:30
Attachments:
signature.asc
|
Dear smartmontools developers! Many thanks for this great software, I tested a USB device successfully, which is not yet in the database. The information about the system, device and tests is as follows: > Linux perle 2.6.35-22-generic #35-Ubuntu SMP Sat Oct 16 20:45:36 UTC 2010 x86_64 GNU/Linux > Bus 002 Device 004: ID 04e8:1f08 Samsung Electronics Co., Ltd > Device Descriptor: > bLength 18 > bDescriptorType 1 > bcdUSB 2.00 > bDeviceClass 0 (Defined at Interface level) > bDeviceSubClass 0 > bDeviceProtocol 0 > bMaxPacketSize0 64 > idVendor 0x04e8 Samsung Electronics Co., Ltd > idProduct 0x1f08 > bcdDevice 0.00 > iManufacturer 1 JMicron > iProduct 11 Samsung S2 Portable > iSerial 3 00000011E093105007D1 > bNumConfigurations 1 > Configuration Descriptor: > bLength 9 > bDescriptorType 2 > wTotalLength 32 > bNumInterfaces 1 > bConfigurationValue 1 > iConfiguration 4 USB Mass Storage > bmAttributes 0xc0 > Self Powered > MaxPower 2mA > Interface Descriptor: > bLength 9 > bDescriptorType 4 > bInterfaceNumber 0 > bAlternateSetting 0 > bNumEndpoints 2 > bInterfaceClass 8 Mass Storage > bInterfaceSubClass 6 SCSI > bInterfaceProtocol 80 Bulk (Zip) > iInterface 6 MSC Bulk-Only Transfer > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x81 EP 1 IN > bmAttributes 2 > Transfer Type Bulk > Synch Type None > Usage Type Data > wMaxPacketSize 0x0200 1x 512 bytes > bInterval 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x02 EP 2 OUT > bmAttributes 2 > Transfer Type Bulk > Synch Type None > Usage Type Data > wMaxPacketSize 0x0200 1x 512 bytes > bInterval 0 > Device Qualifier (for other device speed): > bLength 10 > bDescriptorType 6 > bcdUSB 2.00 > bDeviceClass 0 (Defined at Interface level) > bDeviceSubClass 0 > bDeviceProtocol 0 > bMaxPacketSize0 64 > bNumConfigurations 1 > can't get debug descriptor: Connection timed out > Device Status: 0x5301 > Self Powered > > --- dmesg ---- > [ 134.240122] usb 2-6: new high speed USB device using ehci_hcd and address 4 > [ 134.394003] scsi8 : usb-storage 2-6:1.0 > [ 135.406138] scsi 8:0:0:0: Direct-Access Samsung S2 Portable PQ: 0 ANSI: 2 CCS > [ 135.408068] sd 8:0:0:0: Attached scsi generic sg6 type 0 > [ 135.413346] sd 8:0:0:0: [sdf] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) > [ 135.414237] sd 8:0:0:0: [sdf] Write Protect is off > [ 135.414245] sd 8:0:0:0: [sdf] Mode Sense: 3c 00 00 00 > [ 135.414251] sd 8:0:0:0: [sdf] Assuming drive cache: write through > [ 135.417142] sd 8:0:0:0: [sdf] Assuming drive cache: write through > [ 135.417157] sdf: sdf1 sdf2 > [ 135.444989] sd 8:0:0:0: [sdf] Assuming drive cache: write through > [ 135.445002] sd 8:0:0:0: [sdf] Attached SCSI disk > > --- tests --- > root@perle:~# smartctl -t short /dev/sdf -d usbjmicron -T conservative > smartctl 5.40 2010-03-16 r3077 [x86_64-unknown-linux-gnu] (local build) > Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net > > === START OF OFFLINE IMMEDIATE AND SELF-TEST SECTION === > Sending command: "Execute SMART Short self-test routine immediately in off-line mode". > Drive command "Execute SMART Short self-test routine immediately in off-line mode" successful. > Testing has begun. > Please wait 2 minutes for test to complete. > Test will complete after Sat Nov 13 19:22:11 2010 > > Use smartctl -X to abort test. > root@perle:~# smartctl -l selftest /dev/sdf -d usbjmicron > smartctl 5.40 2010-03-16 r3077 [x86_64-unknown-linux-gnu] (local build) > Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net > > === START OF READ SMART DATA SECTION === > SMART Self-test log structure revision number 1 > Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error > # 1 Short offline Completed without error 00% 0 - Yours sincerly, Dipl.-Ing. Martin Weis |
From: Martin W. <mar...@gm...> - 2010-11-13 18:46:12
Attachments:
signature.asc
|
Dear list! Got some additional information... On 13.11.2010 19:35, Martin Weis wrote: > Many thanks for this great software, I tested a USB device successfully, > which is not yet in the database. The information about the system, > device and tests is as follows: > >> Bus 002 Device 004: ID 04e8:1f08 Samsung Electronics Co., Ltd Hm, with a bit more information the output is maybe not so promising, you may be able to judge better. The drive is new, only short test done. > root@perle:~# smartctl -i -a -x /dev/sdf -d usbjmicron > smartctl 5.40 2010-03-16 r3077 [x86_64-unknown-linux-gnu] (local build) > Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net > > === START OF INFORMATION SECTION === > Device Model: SAMSUNG HM100UX > Serial Number: C0001E86AA4Q9L > Firmware Version: 2AM10001 > User Capacity: 1.000.204.886.016 bytes > Device is: Not in smartctl database [for details use: -P showall] > ATA Version is: 8 > ATA Standard is: ATA-8-ACS revision 6 > Local Time is: Sat Nov 13 19:41:02 2010 CET > SMART support is: Available - device has SMART capability. > SMART support is: Enabled > > === START OF READ SMART DATA SECTION === > SMART overall-health self-assessment test result: PASSED > > General SMART Values: > Offline data collection status: (0x00) Offline data collection activity > was never started. > Auto Offline Data Collection: Disabled. > Self-test execution status: ( 0) The previous self-test routine completed > without error or no self-test has ever > been run. > Total time to complete Offline > data collection: (14400) seconds. > Offline data collection > capabilities: (0x5b) SMART execute Offline immediate. > Auto Offline data collection on/off support. > Suspend Offline collection upon new > command. > Offline surface scan supported. > Self-test supported. > No Conveyance Self-test supported. > Selective Self-test supported. > SMART capabilities: (0x0003) Saves SMART data before entering > power-saving mode. > Supports SMART auto save timer. > Error logging capability: (0x01) Error logging supported. > General Purpose Logging supported. > Short self-test routine > recommended polling time: ( 2) minutes. > Extended self-test routine > recommended polling time: ( 240) minutes. > SCT capabilities: (0x003f) SCT Status supported. > SCT Error Recovery Control supported. > SCT Feature Control supported. > SCT Data Table supported. > > SMART Attributes Data Structure revision number: 16 > Vendor Specific SMART Attributes with Thresholds: > ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE > 1 Raw_Read_Error_Rate 0x002f 100 100 051 Pre-fail Always - 0 > 2 Throughput_Performance 0x0026 252 252 000 Old_age Always - 0 > 3 Spin_Up_Time 0x0023 082 082 025 Pre-fail Always - 5541 > 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 7 > 5 Reallocated_Sector_Ct 0x0033 252 252 010 Pre-fail Always - 0 > 7 Seek_Error_Rate 0x002e 252 252 051 Old_age Always - 0 > 8 Seek_Time_Performance 0x0024 252 252 015 Old_age Offline - 0 > 9 Power_On_Hours 0x0032 252 252 000 Old_age Always - 0 > 10 Spin_Retry_Count 0x0032 252 252 051 Old_age Always - 0 > 11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 1 > 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 6 > 181 Program_Fail_Cnt_Total 0x0022 100 100 --- Old_age Always - 395 > 181 Program_Fail_Cnt_Total <== Data Page | WARNING: PREVIOUS ATTRIBUTE HAS TWO > 191 G-Sense_Error_Rate <== Threshold Page | INCONSISTENT IDENTITIES IN THE DATA > 191 G-Sense_Error_Rate 0x0022 100 100 --- Old_age Always - 1 > 191 G-Sense_Error_Rate <== Data Page | WARNING: PREVIOUS ATTRIBUTE HAS TWO > 192 Power-Off_Retract_Count <== Threshold Page | INCONSISTENT IDENTITIES IN THE DATA > 192 Power-Off_Retract_Count 0x0022 252 252 --- Old_age Always - 0 > 192 Power-Off_Retract_Count <== Data Page | WARNING: PREVIOUS ATTRIBUTE HAS TWO > 194 Temperature_Celsius <== Threshold Page | INCONSISTENT IDENTITIES IN THE DATA > 194 Temperature_Celsius 0x0002 064 064 --- Old_age Always - 30 (Lifetime Min/Max 21/30) > 194 Temperature_Celsius <== Data Page | WARNING: PREVIOUS ATTRIBUTE HAS TWO > 195 Hardware_ECC_Recovered <== Threshold Page | INCONSISTENT IDENTITIES IN THE DATA > 195 Hardware_ECC_Recovered 0x003a 100 100 --- Old_age Always - 0 > 195 Hardware_ECC_Recovered <== Data Page | WARNING: PREVIOUS ATTRIBUTE HAS TWO > 196 Reallocated_Event_Count <== Threshold Page | INCONSISTENT IDENTITIES IN THE DATA > 196 Reallocated_Event_Count 0x0032 252 252 --- Old_age Always - 0 > 196 Reallocated_Event_Count <== Data Page | WARNING: PREVIOUS ATTRIBUTE HAS TWO > 197 Current_Pending_Sector <== Threshold Page | INCONSISTENT IDENTITIES IN THE DATA > 197 Current_Pending_Sector 0x0032 252 252 --- Old_age Always - 0 > 197 Current_Pending_Sector <== Data Page | WARNING: PREVIOUS ATTRIBUTE HAS TWO > 198 Offline_Uncorrectable <== Threshold Page | INCONSISTENT IDENTITIES IN THE DATA > 198 Offline_Uncorrectable 0x0030 252 252 --- Old_age Offline - 0 > 198 Offline_Uncorrectable <== Data Page | WARNING: PREVIOUS ATTRIBUTE HAS TWO > 199 UDMA_CRC_Error_Count <== Threshold Page | INCONSISTENT IDENTITIES IN THE DATA > 199 UDMA_CRC_Error_Count 0x0036 200 200 --- Old_age Always - 0 > 199 UDMA_CRC_Error_Count <== Data Page | WARNING: PREVIOUS ATTRIBUTE HAS TWO > 200 Multi_Zone_Error_Rate <== Threshold Page | INCONSISTENT IDENTITIES IN THE DATA > 200 Multi_Zone_Error_Rate 0x002a 100 100 --- Old_age Always - 0 > 200 Multi_Zone_Error_Rate <== Data Page | WARNING: PREVIOUS ATTRIBUTE HAS TWO > 223 Load_Retry_Count <== Threshold Page | INCONSISTENT IDENTITIES IN THE DATA > 223 Load_Retry_Count 0x0032 100 100 --- Old_age Always - 1 > 223 Load_Retry_Count <== Data Page | WARNING: PREVIOUS ATTRIBUTE HAS TWO > 225 Load_Cycle_Count <== Threshold Page | INCONSISTENT IDENTITIES IN THE DATA > 225 Load_Cycle_Count 0x0032 100 100 --- Old_age Always - 26 > > General Purpose Logging (GPL) feature set supported > ATA_READ_LOG_EXT (addr=0x00:0x00, page=0, n=1) failed: 48-bit ATA commands not supported > Read GP Log Directory failed. > > SMART Log Directory Version 1 [multi-sector log support] > SMART Log at address 0x00 has 1 sectors [Log Directory] > SMART Log at address 0x01 has 1 sectors [Summary SMART error log] > SMART Log at address 0x02 has 2 sectors [Comprehensive SMART error log] > SMART Log at address 0x06 has 1 sectors [SMART self-test log] > SMART Log at address 0x09 has 1 sectors [Selective self-test log] > SMART Log at address 0x80 has 16 sectors [Host vendor specific log] > SMART Log at address 0x81 has 16 sectors [Host vendor specific log] > SMART Log at address 0x82 has 16 sectors [Host vendor specific log] > SMART Log at address 0x83 has 16 sectors [Host vendor specific log] > SMART Log at address 0x84 has 16 sectors [Host vendor specific log] > SMART Log at address 0x85 has 16 sectors [Host vendor specific log] > SMART Log at address 0x86 has 16 sectors [Host vendor specific log] > SMART Log at address 0x87 has 16 sectors [Host vendor specific log] > SMART Log at address 0x88 has 16 sectors [Host vendor specific log] > SMART Log at address 0x89 has 16 sectors [Host vendor specific log] > SMART Log at address 0x8a has 16 sectors [Host vendor specific log] > SMART Log at address 0x8b has 16 sectors [Host vendor specific log] > SMART Log at address 0x8c has 16 sectors [Host vendor specific log] > SMART Log at address 0x8d has 16 sectors [Host vendor specific log] > SMART Log at address 0x8e has 16 sectors [Host vendor specific log] > SMART Log at address 0x8f has 16 sectors [Host vendor specific log] > SMART Log at address 0x90 has 16 sectors [Host vendor specific log] > SMART Log at address 0x91 has 16 sectors [Host vendor specific log] > SMART Log at address 0x92 has 16 sectors [Host vendor specific log] > SMART Log at address 0x93 has 16 sectors [Host vendor specific log] > SMART Log at address 0x94 has 16 sectors [Host vendor specific log] > SMART Log at address 0x95 has 16 sectors [Host vendor specific log] > SMART Log at address 0x96 has 16 sectors [Host vendor specific log] > SMART Log at address 0x97 has 16 sectors [Host vendor specific log] > SMART Log at address 0x98 has 16 sectors [Host vendor specific log] > SMART Log at address 0x99 has 16 sectors [Host vendor specific log] > SMART Log at address 0x9a has 16 sectors [Host vendor specific log] > SMART Log at address 0x9b has 16 sectors [Host vendor specific log] > SMART Log at address 0x9c has 16 sectors [Host vendor specific log] > SMART Log at address 0x9d has 16 sectors [Host vendor specific log] > SMART Log at address 0x9e has 16 sectors [Host vendor specific log] > SMART Log at address 0x9f has 16 sectors [Host vendor specific log] > SMART Log at address 0xe0 has 1 sectors [SCT Command/Status] > SMART Log at address 0xe1 has 1 sectors [SCT Data Transfer] > > SMART Extended Comprehensive Error Log (GP Log 0x03) not supported > SMART Error Log Version: 1 > No Errors Logged > > SMART Extended Self-test Log (GP Log 0x07) not supported > SMART Self-test log structure revision number 1 > Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error > # 1 Short offline Completed without error 00% 0 - > > Note: selective self-test log revision number (0) not 1 implies that no selective self-test has ever been run > SMART Selective self-test log data structure revision number 0 > Note: revision number not 1 implies that no selective self-test has ever been run > SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS > 1 0 0 Completed [00% left] (0-65535) > 2 0 0 Not_testing > 3 0 0 Not_testing > 4 0 0 Not_testing > 5 0 0 Not_testing > Selective self-test flags (0x0): > After scanning selected spans, do NOT read-scan remainder of disk. > If Selective self-test is pending on power-up, resume after 0 minute delay. > > SCT Status Version: 2 > SCT Version (vendor specific): 256 (0x0100) > SCT Support Level: 1 > Device State: Active (0) > Current Temperature: 30 Celsius > Power Cycle Min/Max Temperature: 27/30 Celsius > Lifetime Min/Max Temperature: 27/62 Celsius > Lifetime Average Temperature: 80 Celsius > Under/Over Temperature Limit Count: 0/0 > SCT Temperature History Version: 2 > Temperature Sampling Period: 5 minutes > Temperature Logging Interval: 5 minutes > Min/Max recommended Temperature: -5/80 Celsius > Min/Max Temperature Limit: -10/85 Celsius > Temperature History Size (Index): 128 (59) > > Index Estimated Time Temperature Celsius > 60 2010-11-13 09:05 59 **************************************** > ... ..( 3 skipped). .. **************************************** > 64 2010-11-13 09:25 59 **************************************** > 65 2010-11-13 09:30 58 *************************************** > 66 2010-11-13 09:35 57 ************************************** > 67 2010-11-13 09:40 55 ************************************ > 68 2010-11-13 09:45 53 ********************************** > 69 2010-11-13 09:50 51 ******************************** > 70 2010-11-13 09:55 49 ****************************** > 71 2010-11-13 10:00 47 **************************** > 72 2010-11-13 10:05 45 ************************** > 73 2010-11-13 10:10 43 ************************ > 74 2010-11-13 10:15 42 *********************** > 75 2010-11-13 10:20 41 ********************** > 76 2010-11-13 10:25 40 ********************* > 77 2010-11-13 10:30 40 ********************* > 78 2010-11-13 10:35 39 ******************** > 79 2010-11-13 10:40 41 ********************** > 80 2010-11-13 10:45 41 ********************** > 81 2010-11-13 10:50 40 ********************* > 82 2010-11-13 10:55 41 ********************** > 83 2010-11-13 11:00 40 ********************* > 84 2010-11-13 11:05 48 ***************************** > 85 2010-11-13 11:10 52 ********************************* > 86 2010-11-13 11:15 54 *********************************** > 87 2010-11-13 11:20 56 ************************************* > 88 2010-11-13 11:25 57 ************************************** > 89 2010-11-13 11:30 58 *************************************** > 90 2010-11-13 11:35 59 **************************************** > 91 2010-11-13 11:40 60 ***************************************+ > 92 2010-11-13 11:45 61 ***************************************+ > ... ..( 6 skipped). .. ***************************************+ > 99 2010-11-13 12:20 61 ***************************************+ > 100 2010-11-13 12:25 62 ***************************************+ > 101 2010-11-13 12:30 61 ***************************************+ > 102 2010-11-13 12:35 60 ***************************************+ > ... ..( 2 skipped). .. ***************************************+ > 105 2010-11-13 12:50 60 ***************************************+ > 106 2010-11-13 12:55 61 ***************************************+ > 107 2010-11-13 13:00 60 ***************************************+ > 108 2010-11-13 13:05 60 ***************************************+ > 109 2010-11-13 13:10 60 ***************************************+ > 110 2010-11-13 13:15 61 ***************************************+ > ... ..( 2 skipped). .. ***************************************+ > 113 2010-11-13 13:30 61 ***************************************+ > 114 2010-11-13 13:35 60 ***************************************+ > 115 2010-11-13 13:40 60 ***************************************+ > 116 2010-11-13 13:45 61 ***************************************+ > 117 2010-11-13 13:50 61 ***************************************+ > 118 2010-11-13 13:55 60 ***************************************+ > 119 2010-11-13 14:00 59 **************************************** > ... ..( 14 skipped). .. **************************************** > 6 2010-11-13 15:15 59 **************************************** > 7 2010-11-13 15:20 58 *************************************** > ... ..( 10 skipped). .. *************************************** > 18 2010-11-13 16:15 58 *************************************** > 19 2010-11-13 16:20 59 **************************************** > 20 2010-11-13 16:25 58 *************************************** > 21 2010-11-13 16:30 58 *************************************** > 22 2010-11-13 16:35 58 *************************************** > 23 2010-11-13 16:40 56 ************************************* > 24 2010-11-13 16:45 55 ************************************ > 25 2010-11-13 16:50 53 ********************************** > 26 2010-11-13 16:55 50 ******************************* > 27 2010-11-13 17:00 48 ***************************** > 28 2010-11-13 17:05 46 *************************** > 29 2010-11-13 17:10 44 ************************* > 30 2010-11-13 17:15 42 *********************** > 31 2010-11-13 17:20 41 ********************** > 32 2010-11-13 17:25 40 ********************* > 33 2010-11-13 17:30 39 ******************** > 34 2010-11-13 17:35 39 ******************** > 35 2010-11-13 17:40 40 ********************* > ... ..( 3 skipped). .. ********************* > 39 2010-11-13 18:00 40 ********************* > 40 2010-11-13 18:05 38 ******************* > ... ..( 4 skipped). .. ******************* > 45 2010-11-13 18:30 38 ******************* > 46 2010-11-13 18:35 29 ********** > 47 2010-11-13 18:40 31 ************ > 48 2010-11-13 18:45 32 ************* > 49 2010-11-13 18:50 33 ************** > ... ..( 7 skipped). .. ************** > 57 2010-11-13 19:30 33 ************** > 58 2010-11-13 19:35 27 ******** > 59 2010-11-13 19:40 30 *********** > > Error Write SCT Error Recovery Control Command failed: ATA output registers not supported > Warning: device does not support SCT (Get) Error Recovery Control command > > SATA Phy Event Counters (GP Log 0x11) not supported |